高溫切削 的英文怎麼說

中文拼音 [gāowēnqiēxiāo]
高溫切削 英文
hot machining
  • 高 : Ⅰ形容詞1 （從下向上距離大; 離地面遠） tall; high 2 （在一般標準或平均程度之上; 等級在上的） above...
  • 溫 : Ⅰ形容詞（不冷不熱） warm; lukewarm; hot; gentle; mild Ⅱ名詞1 （溫度） temperature 2 （瘟） acute ...
  • 切 : 切Ⅰ動詞1 （合; 符合） correspond to; be close to 2 （用在反切后頭 表示前兩個字是注音用的反切）見 ...
  • 削 : 削動詞1. （用刀斜著去掉物體的表層） pare [peel] with a knife 2. （乒乓球的一種打法） cut; chop
  • 高溫 : high temperature; elevated temperature; hyperthermia; megatemperature; inferno
  1. Is a hard, brittle, corrosion - resistant, gray to white metallic element extracted from wolframite, scheelite, and other minerals, having the highest melting point and lowest vapor pressure of any metal

    顏色呈灰色或棕黑色，硬度高，延性強，熔點極高，常溫下不受空氣侵蝕主要用途是製造燈絲和高速切削合金鋼，各種鎢電極，也用於光學儀器，化學儀器方面。
  2. The experiments of high speed milling of titanium alloy were conducted under different cooling and lubricating modes, i. e. dry milling, flood coolant, oil mist with nitrogen gas, cryogenic nitrogen gas jet, and cryogenic nitrogen gas jet with minimal quantities of lubricant

    在干銑削、澆注切削液、常溫氮氣油霧、低溫氮氣射流和低溫氮氣射流結合微量潤滑等冷卻潤滑條件下進行了鈦合金的高速銑削對比試驗。
  3. Grinding wheel continues with an infinite number of hard, sharp and refractory grits on edge surface at a high speed of swing operation to cut and grind over the surface of work piece, and unceasing self - sharpening grains and pore continue to grind a tool for every kind of material

    砂輪是經由高速回轉運作中，以其在外緣表面植無數上千萬之硬銳耐溫之小磨粒連續在工作物表面切削磨除，且不斷的自生銳利顆粒與磨屑空隙氣孔，繼續對各種材料做磨削工作的一種研磨工具。
  4. The use of cryogenic nitrogen gas jet to reduce the temperature of cutting zone and to avoid oxidation wear of tool in high speed milling titanium alloy was presented

    為降低切削區溫度、防止刀具的氧化磨損，提出在低溫氮氣射流條件下進行鈦合金的高速銑削加工。
  5. The paper introduces the cutting machining procedure of casting high temperature alloy k423a and researches on the cutting condition in the aspects of cutter material, geometric parameter, and selection of cutting parameter

    摘要對鑄造高溫合金的切削加工進行了分析，重點對k423a的材料特點和加工性能進行了分析，並討其切削加工的條件從刀具材料、幾何參數、切削用量的選擇等方面進行了研究。
  6. Cubic boron nitride ( c - bn ) thin films have significant and potential technological application prospect in cutting tools, electronic and optical devices, etc. because c - bn possesses excellent physical and chemical properties, such as ultrahigh hardness only inferior to diamond, inertness against oxidation at high temperature, uneasy reaction with iron group metal, as well as the possibility of using as n - and p - type doped semiconductors

    立方氮化硼（ c - bn ）具有優異的物理化學性質，如僅次於金剛石的硬度、高溫下強的抗氧化能力、不易與鐵族金屬反應、可n型摻雜也可p型摻雜成為半導體等，立方氮化硼（ c - bn ）薄膜在切削刀具、電子和光學器件等方面有著潛在的重要應用前景。
  7. Cubic boron nitride ( cbn ) thin films have significant and potential technological application prospect in cutting tools, electronic and optical devices, etc., because cbn possesses excellent physical and chemical properties, such as ultrahigh hardness only inferior to diamond, inertness against oxidation at high temperature, uneasy reaction with iron group metal, as well as the possibility of using as n - and p - type doped semiconductors

    立方氮化硼（ cbn ）具有優異的物理化學性質，如僅次於金剛石的硬度、高溫下強的抗氧化能力、不易與鐵族金屬反應、可n型摻雜也可p型摻雜成為半導體等，立方氮化硼（ cbn ）薄膜在切削刀具、電子和光學器件等方面有著潛在的重要應用前景。
  8. On the condition of the test, the cutting force of ticp / fe composites was more than which of 45 steel by 60n, and the cutting temperature was higher than which of 45 # steel by 90, and the roughness of machined surface was almost as much as which of 45 # steel. tic ceramic particles enhanced the cutting force and the cutting temperature of ticp / fe composites, but had little effect on the roughness of machined surface. the machining quality of ticp / fe in situ composite was similarity to 45 # steel

    在本試驗條件下，原位tic _ p fe復合材料切削加工時的切削力與45 ~ #鋼相比要大60n ，切削溫度要高90 ，加工表面粗糙度與45 ~ #鋼相近； tic陶瓷顆粒使原位tic _ p fe復合材料切削加工時的切削力增大、切削溫度增高，對加工表面粗糙度影響不大；原位tic _ p fe復合材料的可加工性與45 ~ #鋼相當。
  9. Kebiao black aluminium oxide abrasive is featured with high hardness, strong tenacity, good self - sharpening, better cohesiseness, higher durability, less heat generated in grinding and giving the metal works high finish, less power weakened in grinding

    以三水型和一水型鋁礬土為原料經電弧爐高溫治煉冷卻加工而成。 "克標"牌黑剛玉磨料基本粒集中，切削力強，韌性大，剛柔相濟，耐磨性好，工效高。
分享友人
分享到 Line

分享到臉書