高溫正火處理 的英文怎麼說

中文拼音 [gāowēnzhēnghuǒchǔlǐ]
高溫正火處理 英文
high temperature normalizing treatment
  • 高 : Ⅰ形容詞1 （從下向上距離大; 離地面遠） tall; high 2 （在一般標準或平均程度之上; 等級在上的） above...
  • 溫 : Ⅰ形容詞（不冷不熱） warm; lukewarm; hot; gentle; mild Ⅱ名詞1 （溫度） temperature 2 （瘟） acute ...
  • 正 : 正名詞（正月） the first month of the lunar year; the first moon
  • 火 : fire
  • 處 : 處名詞1 （地方） place 2 （方面; 某一點） part; point 3 （機關或機關里一個部門） department; offi...
  • 理 : Ⅰ名詞1 （物質組織的條紋） texture; grain （in wood skin etc ） 2 （道理;事理） reason; logic; tru...
  • 高溫 : high temperature; elevated temperature; hyperthermia; megatemperature; inferno
  1. Our company endeavors to quenching & tempering, normalizing, tempering, high and medium temperature quenching, mesh belt furnace quenching, carbonizing, aging subzero and high temperature heat treatment, etc

    本公司是一家致力於從事調質、正火、回火、高中溫淬火、網帶爐淬火、滲碳、時效冰冷及其高溫熱處理的廠家。
  2. The principle of multi - method and multi - parameter is suggested, which should be followed during characterizing microstructures of alloy steels by ultrasonic not method. ultrasonic velocity ( c, ) of transformation products through different heat processes of three steels was measured by high - accuracy ultrasonic installation. the velocity of quenched microstructure of 38crmoal is the lowest, which gradually increases with increasing tempering temperature between 200 ? and 650 ? after quenching process

    利用ti - 40n高精度超聲波測厚儀，研究了超聲波在不同鋼種、不同熱處理轉變產物中的超聲波速度c _ 1 : 38crmoal鋼淬火組織c _ 1最小，淬火后在200 650范圍內進行回火處理時，隨回火溫度的升高， c _ 1逐漸升高， hrc與c _ 1之間具有較好的相關性；正火組織的c _ 1介於淬火后中溫回火及高溫回火產物組織的c _ 1之間。
  3. The difference among the elasticity modulus of various microstructures is probably the main reason, which caused the experiment results above. under the same experiment conditions, such as sample shape, size, surface roughness, establishment of testing system, pressure on the probe, and thickness of coupling medium, the variety of relative attenuation coefficient ( or ) in different heat treatment samples is measured and compared by measuring the attenuation obtained from the cylindrical surface of column. the result is as following : for 40cr and 38crmoal, a mt < az mq < a s < a p + f ; for gcrlssimn, a mt < a annea < s < a p + f ; and a increased with the increasing of frequency

    在保證試樣形狀、尺寸、表面光潔度、系統參數設置、施加在探頭上的壓力以及耦合層厚度等測試條件一致的情況下，利用棒材圓柱面測衰減系數法，分別測定並比較上述不同熱處理試樣相對衰減系數的變化情況，得到的實驗結果是：對於40cr及38crmoal鋼， _ （低溫回火） （淬火） _ （高溫回火） _ （正火） ；對于gcr15simn鋼， _ （低溫回火） _ （退火） _ （高溫回火） _ （正火） ；且隨著頻率的提高，衰減系數均呈現增加的趨勢。
  4. According to structural characteristics of multi - phased alloy steels and the properties of ultrasonic propagation, microstructures characterization with different heat treatment processes ( normalizing, quenching / annealing, quenching plus low tempering, quenching plus high tempering ) for three steels ( 40cr, 38crmoal, gcrlssimn ) was studied experimentally by using ultrasonic methods. ultrasonic velocity, relative attenuation coefficient, and power spectral analyses were researched on the same samples respectively, on the basis of theory and experiment, the sensitivity and other characterizations of the three methods used to distinguish different microstructures were compared

    根據具有多種相結構合金鋼不同熱處理轉變產物的組織特點，以及超聲波在其中的傳播規律，利用超聲波速度、相對衰減系數以及功率譜分析三種方法，對三種鋼（ 40cr 、 38crmoal及gcr15simn ）不同熱處理（正火、淬火退火、淬火+低溫回火及淬火+高溫回火）轉變產物的顯微組織進行了超聲表徵研究。
  5. This company endeavors to hardening, normalizing, tempering, high and medium temperature quenching, mesh belt furnace quenching, cementing, time effective freezing and high temperature treatment etc

    本公司是一家致力於從事調質、正火、回火、高中溫淬火、網帶爐淬火、滲碳、時效冰冷及其高溫熱處理的廠家。
分享友人
分享到 Line

分享到臉書