高爐爐襯 的英文怎麼說

中文拼音 [gāolúlúchèn]
高爐爐襯 英文
blast furnace lining
  • 高 : Ⅰ形容詞1 （從下向上距離大; 離地面遠） tall; high 2 （在一般標準或平均程度之上; 等級在上的） above...
  • 襯 : Ⅰ動詞1 （在裏面托上一層） line; place sth underneath 2 （陪襯; 襯托） set off Ⅱ名詞（襯在裏面的附...
  1. The products are widely applied to lander, branch lander and safety liners of large and medium - sized high furnaces with one - time iron capacity of over 100thousand tons. after rectifying, the iron capacity can be as much as over 300thousand tons

    同時具有抗氧化、耐熱震、烘烤時間短、施工方便等優點，廣泛應用於大中型高爐出鐵主溝、支溝和安全襯，一次性通鐵量十萬噸以上，經修補后通鐵量可達三十萬噸以上。
  2. It is suitable to be used as the medium to filter the high purity and strong corrosive gas or liquid, the air plug of battery, gasket, seals for medium / low pressure, the waveguide tube pre - heater for boiler, the sealing wash, the cover of big - powered micro - wave antenna, and radar antenna of twt etc

    適用於過濾、高純度、強腐蝕性的氣體液體介質、蓄電池上作氣塞、襯墊、中低壓密封元件、鍋爐波管預熱器、密封圈和軍用微波大功率天線罩，以及行饋網路雷達天線等。
  3. The researchers of the company have invented the new high metal alloys materials and place the high position home and abroad. the productions are sold to denmark, japan, england, germany and have won great praise for them

    本公司自行研究的高烙合金耐磨材料（高爐襯板、布料溜槽、反擊式破碎機板錘）已達到國內先進水平，產品一遠銷到丹麥、日本、比利時、英國、德國等海內外，深受用戶好評。
  4. Wear resistant layer of cylinder and double - layer liner in catalyst creaking apparatus ( without or with tortoiseshell net can be used ), inner liner of carbon monoxide exhaust - heat boiler, pouring at site for furnace roof with high temperature of heating furnace of steel rolling, different forging furnace, resistance furnace, the prefabricated parts can also be made

    催化裂化裝置中的筒體耐磨層及雙層襯里， （無龜甲網和有龜甲網均可採用）及一氧化碳余熱鍋爐的內襯，也適用於軋鋼加熱爐、各種煅造爐、電阻爐的爐頂、爐墻、爐底高溫部位的現場澆注，可製成預制構件。
  5. Blast furnace tear down apparatus

    高爐舊爐襯拆除設備
  6. Abstract : using magnesia ramming materials in furnace bottom and partial hearth instead of traditional shaped magnesia bricks can prolong furnace life, reduce refractories consumptions per one ton product and increase equipment utilization rate

    文摘:敘述了中低碳錳鐵精煉爐用鎂質搗打料在爐底與部分爐缸取代傳統的成型鎂磚作爐襯材料，達到了延長爐齡、降低噸產品耐火材料消耗、提高設備作業率的目的。
  7. It is widely applied to the stove top, shove head, stove door and burmer brick, the binding of cooling - tube and groove bottom of the molten steel mouth of the heat stove, meantime empopyed in the field of the step stove bottom, the fir - proof wall of the circular stove, the cover, the protruding tape and sand sealing mouth of the equal - heating stove, the triangle, the spray gun and meltingiron groove of electric stove and also including fire - resistant material used in the refine stove and the stove door

    加熱爐的爐頂、爐頭、爐門、燒嘴磚、水冷管包紮、出鋼槽槽底、步進爐爐底、環形爐檔火墻、均熱爐的爐蓋、凸出帶、砂封口、中間包包蓋、電爐三角區、鐵水包襯里、爐外精煉用噴槍，底吹氧煙道、鐵水溝蓋、檔渣堰、高爐中各種耐用火料襯里煉焦爐爐門等。
  8. High - temp molanstone heat - insulation brick is made with domestic newest energy - effcient fire - proof material by using advaned technologies introduced from abroad. it has the strengths of heat - resistance, high intensity, low heat - conduction coefficient and remarkable energy - saving effects. it can be used in petrolum partition kiln, metallurgical hot stove, ceramic kiln, tunnel kiln, and as linings of many electric stoves. it can also used on fire directly. according to the testing of relevant authorities, this product has reached standards of products from foreign competitors

    高溫莫來石質絕熱磚是我國引進的新技術，國內最新型的節能耐火材料，具有耐高溫、強度高導熱系數小，節能效果顯著等特點，適用於石油裂介爐、冶金熱風爐、陶瓷輥道窯、隧道窯、電瓷抽屜窯、玻璃坩堝窯及各種電爐的內襯，可直接接觸火焰、經有關技術監督部門檢測及使用，產品達到國外同類產品的技術指標。
  9. In order to search the demolishing effect pf the thermal stress on the hearth and bottom of the blast furnace, the distribution of temperature field and the thermal stress have been studied with the thermal elastic law and finite element method

    摘要為了探討熱應力對不同材質構成的高爐爐缸磚襯的破壞作用，在計算溫度場的基礎上，應用熱彈性理論和有限元法對高爐爐缸進行應力分佈計算。
  10. Through researching the con - structon methold of explording stove lump, disposing blasting residual things, residual waste iron of furnace bottom and furnace waist brick, we have developed the disposion stove liners construction craft in the middle and later term of construction blast furnace in pangang group

    通過對炸爐瘤、處理爆破殘留物、爐底殘渣鐵和爐缸磚的施工處理方法的研發，形成了攀鋼高爐中後期爐襯處理施工工藝。
  11. Series of injection mixes for blast furnace are easy to spread at the lining surface, with solid adhesion strength withmatrix, adaptiing to injection repairing of inlings of blast furnaces

    本廠生產的系列高爐壓入修補料具有延展性好，與基面結合牢固的特點，適用於高爐爐襯的壓入修補。
  12. Furthermore, the growth and the study of self - organized quantum dots structures become more and more important recently, and the application of self - organization technique become wider and wider in this thesis, we address the theory of film growth and the growth technique firstly more, the ways and characteristics of surface detection are prescribed we mainly report the growth process, results and discuss of self - organized quantum dots structures in the a12o3 substrates by s - k mode using ecr - mocvd, in the espd - u device the growth art of ain epilayer which is the preliminary foundation of self - organized gan / ain quantum dots structures, including the substrate cleaning, nitridation, the growth of buffer and the growth of gan and ain epilayer, is discussed we deliberately compare the test result of rheed xrd and afm and achieved the optimalized condition of ain at last we have successfully realized the growth of ain which is much smooth and better crystal quality moreover, we grow the self - organized gan / ain quantum dots structure in s - k mode because the limits of the heater temperature, we can not grow the atom - smooth epilayer of ain until now so we could not grow better quantum dots which have small diameter and big density but the self - organized quantum dots structures with better quality will be realized successfully if the substrate temperature is increased the thesis study belong to my tutor subject of national nature science foundation ( 69976008 )

    本論文主要論述了在espd - u裝置上，採用電子迴旋共振等離子體增強mocvd （ ecr - pamocvd ）方法，在藍寶石襯底上通過s - k模式自組裝生長gan aln量子點結構的生長工藝、結果及討論。而重點分析了自組裝生長量子點之前的aln外延層生長工藝，包括襯底清洗、氮化、緩沖層的生長和gan 、 aln外延層的生長；通過高能電子衍射、 x射線衍射和原子力顯微鏡測試，並且對這些測試結果進行了詳細的比較研究，得出了較優化的工藝條件，生長出了晶質較好、表面較平整的aln外延層；進而採用s - k模式自組裝生長了gan aln量子點結構。由於實驗裝置加熱爐溫度的限制，我們沒有能夠生長出原子級平滑的aln外延層表面，因而沒能夠生長出密度比較大和直徑比較小的量子點。
  13. In this paper, using microcomputer technigue, old heat - treatment furnaces is remoulded with light and ultra - light furnace - lining materials, which is the most effctive approach for heat - treatment furnace to save energy

    採用微機技術對舊熱處理爐進行改造，使爐襯材料輕質或超輕質化，是提高熱處理爐節能的有效途徑。
  14. The stove liner of blast furnace is damaged seriously for the influence of iron water melting metal, chemical corrosion of stove residual and furnace lump in the middle and later term

    摘要由於鐵水熔融金屬以及爐渣的化學侵蝕和爐瘤的影響，高爐中後期爐襯受損嚴重。
  15. This paper introduces the preloading model set technological in heating furnace, preloading model set technological can increase the quality of heating furnace and the life of furnace lining highly

    摘要在加熱爐中採用預加載荷支模工藝，能提高加熱爐施工質量，大大提高爐襯壽命。
  16. Abstract : the structure, characteristics and application of or dina ry coal - dust - injection guns used in blast furnaces is introduced and the reaso ns the curved coal - dust - injection gun should replace straight one and ceramic - lined composite gun head should replace straight stainless steel one have been put fo rward. the performance of curved guns used at baosteel and shougang and the pros pect of this new type of gun has been given

    文摘:對目前國內高爐採用的普通型煤粉噴槍的結構、特點及使用情況進行了分析並指出其不足，提出了將直煤槍改為彎煤槍；用陶瓷內襯復合彎槍頭取代不銹鋼直槍頭的觀點與理由，給出了陶瓷內襯復合彎槍在寶鋼、首鋼高爐的應用情況，並對其發展進行了展望。
  17. Based on the mechanism analysis and ai technique, an optimization and decision - making model about operating parameters and an on - line simulation and detection model in the copper matte blowing process are built. a model to forecast the copper - making end point is also built by using smoke temperature in a factory. on the research mentioned above, the intelligent decision support system of the operation - optimization is developed

    在上述研究基礎上，開發了銅鋶吹煉爐優化操作智能決策支持系統，將其應用於生產實踐，使粗銅產量提高了6 . 0 ，冷料處理量提高了7 . 8 ，爐襯壽命由原來的213爐提高到235爐，提高了10 . 3 。
  18. It is made of fused magnesite and high purity flake graphite by adding metal composite antioxidant and phenolic resin as binder. it has the excellent properties of corrosion resistance, spalling resistance, resistance to oxidation and better thermal shock resistance. it can be used in all kinds of converters, eaf, refining ladles and common ladles. upon request, multiple lining - up designs of reasonable materials can be provided according to the working conditions of above mentioned furnaces

    採用電熔鎂砂、高純鱗片石墨為主要原料，添加金屬復合抗氧化劑，以酚醛樹脂為結合劑製成的製品具有優良的抗浸蝕性、抗剝落性、抗氧化性和良好的抗熱震性，適用於各種容量的轉爐、電爐、精煉鋼包及普通鋼包，本公司可根據用戶要求，針對上述4種熱工窯爐的具體使用條件提出爐襯的材質綜合砌築方案。
  19. Corundum mullite product adoprs electrocast refractories. through high pressure formation and high temperature burning, this product has comparatively high refractoriness, mechanical strength and slftening temperature under load. it can be widely used as inner lining. of various industrial furnace under such hard working conditions as high temperature, flushing and erosion

    剛玉莫來石製品是採用電熔合成原料，高壓成型，高溫燒成的具有較高耐火度及機械強度，較高荷重軟化濁的可廣泛應用於各類工業爐高溫、沖刷、侵蝕條件較苛刻的窯爐內襯的耐火製品。
  20. Used for lining in blast furnaces, hot air stoves, coke ovens and other industry furnaces

    用於各種工業爐窯的耐火內襯，如高爐、熱風爐、加熱爐、均熱爐、鍋爐等。
分享友人
分享到 Line

分享到臉書