高速噴流 的英文怎麼說

中文拼音 [gāosùpēnliú]
高速噴流 英文
fast-moving jet
  • 高 : Ⅰ形容詞1 （從下向上距離大; 離地面遠） tall; high 2 （在一般標準或平均程度之上; 等級在上的） above...
  • 速 : Ⅰ形容詞（迅速; 快） fast; rapid; quick; speedy Ⅱ名詞1 （速度） speed; velocity 2 （姓氏） a surna...
  • 噴 : 噴動詞1. （液體等受壓力而射出） spurt; spout; gush; jet 2. （噴灑） spray; sprinkle
  • 流 : Ⅰ動1 （液體移動; 流動） flow 2 （移動不定） drift; move; wander 3 （流傳; 傳播） spread 4 （向壞...
  • 高速 : （高速度） high speed; high velocity （hv）; high rate; swift; fast; express; high-speed
  1. Through the special studies on impacts to atomizing and humidifying effect from such factors as the firing pin type, centrifugal structure, higher spraying pressure, less aperture, initial water temperature and original state of the air, some conclusions are obtained, such as : the centrifugal nozzle with firing pin type, high pressure and little aperture has bigger air eddy and atomizing angle. the spaying liquid has high velocity. the droplet is small, and the heat and mass transfer velocity is high

    通過對撞針型結構、離心式結構、較高的噴水壓力、較小的噴嘴孔徑、噴水初溫及待加濕空氣初狀態對霧化加濕效果的作用原理的重點分析，得到：撞針型高壓小孔徑離心式噴嘴具有較大的空氣渦與霧化角，噴出的液體流速高、液滴小、水與空氣傳熱傳質速率高，撞針型結構提高了霧化加濕效率，高壓小孔徑的特點為霧化加濕提供了較大的能量，而噴水初溫的升高會減小水的粘性力和表面張力，從而優化加濕效果。
  2. The effect of the height between nozzles and ground plate, the distance between the nozzles, the inlet velocity of the nozzles, and the velocity of the cross flow on the flowfield structure were studied one by one

    分別就噴嘴距地面高度、噴嘴間距、噴嘴出口速度、橫向流等，對噴射垂直撞擊平板流場的影響，逐一討論。
  3. Washed air purifier working principle : siphon and using centrifugal principle will be mixed in water pure plant essential oils inhaled through its siphon principle the motor base coaxial centrifugal turbines in the bottom of straw through exchanges cover a very high - speed rotary motor, reuse centrifugal principle, will be mixed in water pure plant essential oil spray bottle in the form within a water film bile, the dust in the air and inhaled bacteria in water purification at the same time after the indoor air insufflation, quickly and efficiently by removing indoor toxin biological, dust, cigarette smoke, the smell, virus

    水洗空氣清新機工作原理：是利用虹吸以及離心原理；將混合於水的純植物精油通過虹吸原理吸入其電機底座的同軸離心渦輪下部的吸管中，通過交流罩極電機高速旋轉，再利用離心原理，將混合於水的純植物精油噴在瓶膽內形成一層水膜，將空氣中的灰塵以及細菌吸入水中，同時將經過凈化的空氣吹入室內，快速有效地去除室內的有毒素生物、灰塵、煙味、臭味、病毒等。
  4. The lateral jets are caused to incline to the direction of rotating free flow and to weaken the effect upon base flow. furthermore, the spinning effect upon lateral jet is much stronger than that upon base bleed

    與無旋轉情況對比表明，旋轉對彈丸側噴流以及底部流動均有影響，高速旋轉導致側噴射流向旋轉來流方向傾斜，並減弱其對彈底流動的引射。
  5. Three dimensional interaction flowfield over high - speed spinning projectile with lateral jets is numerically simulated in this dissertation firstly. complicated shocks wave patterns is analyzed. several factors concerned such as high - speed spinning, attack angle, base bleed and so on, are studied

    本文首次完成了高速旋轉彈丸側噴三維干擾湍流流場的數值模擬，分析了彈丸側噴流場復雜的波系結構，研究了高速旋轉、攻角、底噴等因素對彈丸側噴流場的影響規律，深入分析了旋轉側噴彈丸的空氣動力學特性。
  6. Highways winter maintenance plant and highways side equipment maintenance - deicing agent sprayer - fixed station test method for flow rate measurement

    高速公路冬季維修設備和高速路路邊設備維修.除冰劑噴灑機.流率測量固定站試驗方法
  7. Focusing on the performance evaluating and the design of tripropellant injector, adopting the cold test rig with background pressure supply, malvem particle analyzer, ccd photography system, tripropellant hot test - bed, numerical simulation software and auxiliary theoretical a nalysis, the d ischarge c haracteristic a s w ell a s a tomization p erformance o f the injector and the combustion performance as well as the mode - transition characteristic of thrust chamber are studied detailedly based on the 3 different structures of coaxial tripropellant injector, large numbers of important conclusions are gained

    本文圍繞三組元噴嘴的性能評定及設計方法。採用反壓冷試臺、馬爾文測粒儀、 ccd高速攝影系統、三組元發動機熱態試驗臺、數值模擬程序及輔助理論分析等多種技術手段和研究方法，對三種結構的同軸式三組元噴嘴深入進行了噴嘴流量特性和霧化特性、推力室燃燒性能和轉工況性能研究，得到了大量重要結果。
  8. Exhaust carrying sulfur oxides and powders enter the venturi scrubber to interact with the recovery solvent. when passing through the neck, the section surface constricts and the

    含硫氧化物及粉塵廢氣自頂部進入文氏洗滌塔和洗滌液接觸流經喉部，由於截面積縮小，高速氣體將洗滌液噴成霧狀，而達到慣性沖擊去除粒狀物的目的。
  9. At high speed and hot exhaust flow conditions, a preliminary experimental investigation on the divergent wall cooling of two dimensional c - d nozzle had been conducted

    摘要在高速熱噴流條件下，對二元收擴噴管超音段壁面的冷卻進行了初步試驗研究。
  10. Material is ejected into the crushing chamber by means of high speed ejection flow formed by high - pressure air through charging ejector, and the crushing nozzles outside ejects high - speed airflow into the crushing chamber at certain direction, making the materials severely collided and fractionated, and thus crushed

    該機是靠高壓氣體通過加料噴射器所形成的高速射流，使粉碎原料被射入料碎室，粉碎室外圍的粉碎噴嘴，有方向性的向粉碎室噴射高速氣流，使物料間產生激烈的碰撞，磨擦而獲得粉碎。
  11. Mainly for the engraving of anti - counterfeiting signs for the packages of tobacco alcohol sugar tea cosmetics and various other high - quality products. the machine can work quickly and in an allembly line at a low cost. the highest speed of engraving is 300mm s. and the marimum moving speed is 5 - 300cm min adjutable. the differentiation rate is 0. 0125mm and is under the control of high - speed one - chip cpu

    本機噴碼速度快，可上流水線生產，價位低，品質高，最大雕刻速度300 s ，最大移動速度5 - 300cm mm可調，解析度為0 . 0125mm ，高速單片機控制。
  12. The paper introduces the basic principle of the inducement type ventilation in the province of aerodynamics : disturbed characteristic of high - speed cascade can effectively leads quiescent air around it and drive air flow, compares and analyzes the traditional ventilation type and inducement ventilation type applied in underground garage in the facets of airflow organization, practicability and economy, coming to the conclusion that the inducement type ventilation is applied to the underground garage in the facets of economy, practicality and high efficiency

    摘要介紹了誘導式通風利用空氣動力學中高速噴流的擾動特性，能夠有效地誘導周圍靜止的空氣，帶動空氣流通的基本工作原理，就傳統通風方式和誘導通風方式，在地下車庫應用中的氣流組織、實用性、經濟性等幾個方面做了比較，分析認為，誘導式通風因其經濟、適用、高效的特性適合在地下車庫應用。
  13. Electrospinning origins from that electrically charged fluid is forced jets in the high voltage electrostatic field. electrospinning occurs when the electrical forces at the surface of a polymer solution or melt overcome the surface tension and cause an electrically charged jet to be ejected. when the jet dries or solidified, an electrically charged fiber remains

    電紡絲技術是基於高壓靜電場下導電流體產生高速噴射的原理發展而來，其基本過程是：聚合物溶液或熔體在幾千至幾萬伏的高壓靜電場下克服表面張力而產生帶電噴射流，溶液或熔體射流在噴射過程中乾燥、固化，並保持一定電荷量，最終落在接收裝置上形成纖維氈或其它形狀的纖維結構物。
  14. Two relevant models are intro - duced : ( 1 ) the neutrino rocket model for neutron stars with high velocities ; ( 2 ) the 3p2 - superfluid phase transi - tion model for pulsar glitches

    介紹了與之有關的兩個模型： （ 1 ）高速中子里的中微子火箭噴流模型； （ 2 ）脈沖星周期突變的3p2中子超流渦旋渦旋相振蕩模型。
  15. Put up the cold experiment of the three - phase fluidized bed with multiple orifice balls, research on the influence of the superficial gas velocity, the filler static height and the liquid density on the resistance character and the desulfurized efficiency, summarize the virtue of multiple orifice balls

    摘要對多孔球為填料的三相流化床進行冷態試驗研究，研究不同工況下氣體空塔流速、填料靜止高度、噴淋密度等因素對流化床阻力特性和脫硫效率的影響。
  16. After the function of cutting, lashing and scraping produced by the strong force, and then becoming granule and being scatted, a part of the disposed liquid will spurt out from the spurting mouth at the upper of the container

    部分由具有高轉速的獨特的輪機與具有放射狀折流板之作用的定子的被處理液就任由高速回轉中的輪械與定子之間所產生的強力的剪斷、沖擊、刮流等過程，而被細粒化及分散，而由上方之噴出口往上噴出。
  17. A new high speed and great flow solenoid valve, one of the key parts of electronically controlled fuel injection, is assembled, adjusted, which makes it in good condition, and prepares for injection test in this thesis

    電磁閥作為電控燃油系統中極為關鍵的部件，它對燃油噴射特性影響特別大。故本文對課題組自行開發、研製的高速大流量電磁閥進行了裝配、調試，使其液力狀況最佳，為噴油實驗作前期的準備工作。
  18. In the aero - optical flow field tomography measurements, all projection data of different direction must be simultaneous. and the laser nozzle flow field up - stream and down - stream strehl ratio simultaneous measurements have the synchronicity requirement. the working environment of high power laser is rigorous and complicated

    在考慮了由於氣動光學流場層析測量中的多個投影方向數據的同時測量、激光器噴管流場上游和下游同時測量的同步要求，以及高能激光平臺的復雜環境多方面因素的基礎上，考慮了硬體匹配的一些問題，設計了一套高速的線陣s - h傳感器。
  19. Lateral jet control technology is researched in this dissertation, based on supersonic / hypersonic missile aerodynamics and lateral jet interaction ( ji ) effects associated with the attitude control solid - propellant rocket motors system in the low endoatmospheric range

    橫向噴流干擾效應研究在超聲速高超聲速導彈總體設計和精確制導技術研究領域一直佔有重要地位。本論文針對大氣層內超聲速高超聲速導彈採用姿態固體火箭發動機側噴流控制技術的一些問題進行了研究。
  20. And based on the simulation of dynamic arc characteristics during the interrupting process, the interactive mechanism of the arc and high velocity gas flow has been deeply analyzed, the variation of the gas flow parameters under the condition of arc clogging and interaction of arc and shock wave have been studied

    在斷路器開斷過程動態電弧特性模擬的基礎上，深入解析了電弧與高速氣流的相互作用機理，研究了電弧堵塞情況下噴口氣流參數的變化，電弧與激波的沈陽工業大學博士學位論文摘要相互作用等。
分享友人
分享到 Line

分享到臉書