高速磨削 的英文怎麼說

中文拼音 [gāosùmóxiāo]
高速磨削 英文
high speed grinding
  • 高 : Ⅰ形容詞1 （從下向上距離大; 離地面遠） tall; high 2 （在一般標準或平均程度之上; 等級在上的） above...
  • 速 : Ⅰ形容詞（迅速; 快） fast; rapid; quick; speedy Ⅱ名詞1 （速度） speed; velocity 2 （姓氏） a surna...
  • 磨 : 磨動詞1 （摩擦） rub; wear 2 （研磨） grind; mull; polish 3 （折磨） grind down; wear down [out]:...
  • 削 : 削動詞1. （用刀斜著去掉物體的表層） pare [peel] with a knife 2. （乒乓球的一種打法） cut; chop
  • 高速 : （高速度） high speed; high velocity （hv）; high rate; swift; fast; express; high-speed
  1. The results show that the process of concrete sawing with diamond tools is that the impact of diamond sawblade induces the rupture and break of concrete surface layer during high speed sawing ; cement and carpolite become micro chips by the cutting of diamond grits ; steel fiber and steel wire are broken by plastic deformation or pulled out by forces

    結果表明：金剛石鋸片鋸切混凝土的過程表現為高速據切過程中金剛石據片的沖擊引起混凝土表層斷裂破碎，水泥石子等在切削區內層受到金剛石磨粒的微切削作用形成粉屑，以及鋼纖維和鋼絲發生金屬塑性變形斷裂或被拔拉而斷裂的過程。
  2. Grinding wheel continues with an infinite number of hard, sharp and refractory grits on edge surface at a high speed of swing operation to cut and grind over the surface of work piece, and unceasing self - sharpening grains and pore continue to grind a tool for every kind of material

    砂輪是經由高速回轉運作中，以其在外緣表面植無數上千萬之硬銳耐溫之小磨粒連續在工作物表面切削磨除，且不斷的自生銳利顆粒與磨屑空隙氣孔，繼續對各種材料做磨削工作的一種研磨工具。
  3. For grinding hss and carbide engraving cutter as well as single lip or multiple lip cutters of various shapes such as radiuses cutters or negative taper angle of cutters

    該機可用於磨削各類形似半圓角或反錐角的高速鋼和硬質合金雕刻刀具和單邊或多邊刀具。
  4. For grinding hss and carbide engraving cutter as well as single lip or multiple lip cutters of various shapes such as radiused cutters or negative taper angle of cutters

    該機可用於磨削各類形似半圓角或反錐角的高速鋼和硬質合金雕刻刀具和單邊或多邊刀具。
  5. Adhesive wear is the main abrasion mechanism of composite in high sliding speed and heavy - load. the adhesive wear is the main abrasion mechanism when the size of filling is minor or the content of filling is low. with the increase of the size or the content of filling, the mainly abrasion mechanism transit from adhesive wear to grinding abrasion

    （ 2 ）在低速低載時，復合材料的磨損以犁削磨損為主，在高速高載時，復合材料的磨損以粘著磨損為主；在填料粒徑較小或填料含量低時復合材料的磨損以粘著磨損為主，隨顆粒含量的增大或填料粒徑的增大，復合材料的磨損變為以磨料磨損為主。
  6. The product is suitable for double straight line smoothing of grinding flat glass. coarse grinding, fine grinding, and polishing can be done at one time. adopt plc control system, which sets processing parameters via interface, and finishes processing at one time, ti has stable bottom structureprecise and smooth transmission system, the transmission belt drive adopts strong power and tran - sfrequency motor to control speed, constant power, constant rule, output and advanced equipment to control, completed product has high polishing level, which is an ideal option assistant processed equipment of processing delicacy glass and furniture glass factory

    本產品適用於磨削平板玻璃是雙直線平邊，粗磨精磨拋光一次完成採用plc控制系統通過界面設定加工參數次完成加工，具有穩重扎實的底座結構，精確流暢的傳動系繞，傳送皮帶驅動採用功率變頻電機調速控制，恆功率恆扭矩輸出和高配置的控製成品拋光亮度高是加工精品玻璃和傢具玻璃廠家使用的最佳輔助加工設備。
  7. It is simple to operate, fluent to transfer and high work efficiency

    將磨削拋光完畢的水鉆從模具上取下。速度快效率高。
  8. The results show that, when increasing the feed rate of the grinding wheel, decreasing the rotating speed of the wafer chuck table and using coarser grit grinding wheel, the material removal rate in the wafer rotating grinding increase, the feed rate of the grinding wheel has greater influence on the material removal rate ; when suitably increasing the rotating speed of the grinding wheel, decreasing the feed rate of the grinding wheel and using finer grit grinding wheel, the wafer surface roughness can be reduced ; there exists a critical rotating speed of the grinding wheel ( about 2300rpm ), beyond which the material removal rate evidently decreases and the spindle motor current and wafer surface roughness steeply increase ; when the grit size of the grinding wheel is finer than # 2000, the material removal rate decreases and the wafer surface roughness has no obvious improvement

    研究結果表明，增大砂輪軸向進給速度和減小工件轉速，採用粗粒度砂輪有利於提高磨削矽片的材料去除率，砂輪軸向進給速度對材料去除率的影響最為顯著；適當增大砂輪轉速，減小砂輪軸向進給速度，採用細粒度砂輪可以減小磨削表面粗糙度；在其它條件一定的情況下，砂輪速度超過一定值會導致材料去除率減小，主軸電機電流急劇增大，表面粗糙度變差；採用比# 2000粒度更細的砂輪磨削時，材料去除率減小，矽片表面粗糙度沒有明顯改善。
  9. It has many advantages, such as high grinding efficiency, low grinding temperature, high grinding accuracy, low grinding cost, etc

    它具有加工效率高、 「冷態」磨削、磨削速度穩定、磨削精度高、磨削成本低等特點，在機械製造中佔有愈來愈重要的地位。
  10. Aiming at the key component, through analyzing the time domain and frequency characteristic of acceleration vibration signals and force signals, this paper attempts to find the infection factors of grinding vibration and to optimize the grinding parameters, which is based on ultra - high speed surface grinding experimentation

    摘要以關鍵部件為研究對象，通過在超高速磨削實驗臺上進行磨削工藝試驗，對比不同參數下加速度振動信號和磨削力信號的時頻特徵，分析了磨削過程振動特性及其各種影響因素，提出磨削工藝參數優化方案。
  11. The wear patterns and wear mechanisms of solid cemented carbide are analyzed in high - speed milling of aluminum alloy

    摘要對硬質合金整體立銑刀高速銑削加工航空鋁合金時的刀具磨損形態及其磨損機理進行了觀察和分析。
  12. The use of cryogenic nitrogen gas jet to reduce the temperature of cutting zone and to avoid oxidation wear of tool in high speed milling titanium alloy was presented

    為降低切削區溫度、防止刀具的氧化磨損，提出在低溫氮氣射流條件下進行鈦合金的高速銑削加工。
  13. High - speed steel machine taps with ground threads. technical specifications

    帶磨削螺紋的高速鋼機用絲錐.技術規范
  14. Based on the characteristics of ultrahigh speed grinding, the general selection principle of abrasives, binders, hardness, concentration and structure of ultrahigh speed cbn wheels is discussed

    摘要結合超高速磨削的特點，論述超高速cbn砂輪中磨料、結合劑、硬度、濃度、組織的一般選用原則。
  15. The authors describe the principle, application and merits of ultra - high - speed grinding ( ulsg ), and analyzes the technical conditions relative to the implementation of ultra - high speed grinding, and give an overview on the development of ulsg in our country

    介紹了超高速磨削的原理，對超高速磨削的應用和優勢進行了闡述，並分析了實現超高速磨削的相關技術條件，綜述了我國在超高速磨削研究方面的工作
  16. For such materials with great hardness and toughness as stainless steel, high vanaduim - high speed steel, particularly for the work piece liable to deform or to be burnt, and for dry grinding

    適用於高硬度、高韌性材料如不銹鋼、高釩高速鋼的磨削，特別是用於干磨和變形、易燒傷工件的磨削加工，效果更好。
  17. Application of ultra - high speed grinding technologies in the field of the mechanical machining

    超高速磨削技術在機械製造領域中的應用
  18. Emphasis is laid on the importance of the core of ultrahigh speed wheels, design requirement and material selection

    重點強調超高速磨削砂輪基體的重要性和設計要求以及材料的選擇。
  19. Finally, the position of the ultrahigh speed wheels in ultrahigh speed grinding and our research direction in future are pointed out

    最後，指出超高速磨削砂輪在超高速磨削中的地位，並指出努力方向。
  20. Abstract : the authors describe the principle, application and merits of ultra - high - speed grinding ( ulsg ), and analyzes the technical conditions relative to the implementation of ultra - high speed grinding, and give an overview on the development of ulsg in our country

    文摘:介紹了超高速磨削的原理，對超高速磨削的應用和優勢進行了闡述，並分析了實現超高速磨削的相關技術條件，綜述了我國在超高速磨削研究方面的工作
分享友人
分享到 Line

分享到臉書