高速針閥 的英文怎麼說

中文拼音 [gāosùzhēnfá]
高速針閥 英文
high-speed needle valve
  • 高 : Ⅰ形容詞1 （從下向上距離大; 離地面遠） tall; high 2 （在一般標準或平均程度之上; 等級在上的） above...
  • 速 : Ⅰ形容詞（迅速; 快） fast; rapid; quick; speedy Ⅱ名詞1 （速度） speed; velocity 2 （姓氏） a surna...
  • 針 : Ⅰ名詞1 （縫衣物用的工具） needle 2 （細長像針的東西） needle like things 3 （針劑） injection; sh...
  • 閥 : 名詞1 （指在某方面有支配勢力的人物或家族） established house or power group; a powerful person or...
  • 高速 : （高速度） high speed; high velocity （hv）; high rate; swift; fast; express; high-speed
  1. First, it is compressible and cushiony ; second, it can be transported to a long distance with a little power loss ; the last, its flux and velocity of flow are quite high, so the reaction time of the operators can been considerably shortened. aiming to solve the problems of vibrating machinery such as short life - span, poor cushion and high energy consumption, the writer, on the basis of characteristic of pneumatic mentioned, contrives a set of valve controlled pneumatic vibrator, which has larger output vibrating force and longer life - span with simple structure. then, it is applied to drive a vibrating screen and the result is fairly well

    文中針對氣動技術本身的特性及優點，如：可壓縮，具有緩沖性；能耗損失小，便於遠距離輸送；流量大、流速高，執行元件響應速度快等，以解決振動機械在應用過程中的緩沖、能耗以及使用壽命等問題為目的，設計出一套輸出激振力大、結構簡單、使用可靠的閥控氣動激振器，並將其成功地運用到振動篩上，取得了較好的效果。
  2. This paper supplied a new way through variable frequency variable speed ( vfvs ) to change its output flow rate and adding a constant - pressure - drop valve, which could solve the defects in hydraulic pressure servo control system, such as low efficiency in control system, short life, poor ability in resisting pollution, low efficiency in driving system and flow rate, pressure pulse. and this way was proved to be effective

    本論文針對傳統伺服控制系統效率不高、元件壽命短、抗污染能力差、驅動系統效率低、存在流量及壓力脈動等缺陷，利用先進的交流變頻調速技術改變液壓泵轉速的容積調速新方法，提出了在液壓系統中加一個定差減壓閥的新思路，較好地解決了液壓伺服系統存在的上述問題。
  3. In order to resolve the problem of fast switching on or off, intellectual control and smaller bulk of high voltage power required in er valve, a nc high - voltage power source is designed and made using singlechip technology and high frequency switch power technology,

    針對電流變閥對高壓控制電源要求的快速通斷及智能控制和體積小的特點，採用單片機技術與高頻開關電源技術，設計製作了一臺用於電流變閥控制的數控高壓電源裝置。
  4. Recently, a new kind, two - position and three - way solenoid valve with great rate of flow and high speed as well as its test bed has been developed by school of energy and power engineering, wuhan university of technology. results have shown that it can control the injection of the diesel engine preferably. the research work in this paper has been done concerning on the solenoid valve and its test bed, which is listed as following

    武漢理工大學能源與動力工程學院為其所配系統開發研製的一種二位三通大流量高速電磁閥，具有響應快、流量大等特點，能較好的實現對噴油過程的柔性控制，同時，該院還開發了電磁閥專用的測試裝置，本文的研究工作即是針對電磁閥及其測試裝置的進一步優化而展開的，分別如下。
  5. The objective of this dissertation is a kind of press - high speed numeric control oil - press. with a theoretical analysis and study about proportional control system, this paper sets up the mathematical model of proportional valve controlled non - symmetry hydraulic cylinder via the hydraulic system model building. then analyzes and modifies the model based on the matter of this study, and simulates the model with matlab software to confirm pid parameters, thus designs the pid controller

    本學位論文針對一具體的研究項目?高速數控壓機的開發，對比例控制系統進行理論分析與研究，通過對液壓系統的精確建模，建立起比例閥控非對稱液壓缸的數學模型，然後根據所研究問題的實際情況對模型進行必要的分析和修正，再運用模擬軟體matlab分析系統模型及確定pid控制參數，設計出pid控制器，使得控制系統的設計具有更多的可靠性和靈活性，最後運用pic單片機實現此控制，並結合整機調試試驗驗證了pid控制的成功。
分享友人
分享到 Line

分享到臉書