高頻激勵 的英文怎麼說

中文拼音 [gāobīnjīlì]
高頻激勵 英文
high frequency pumping
  • 高 : Ⅰ形容詞1 （從下向上距離大; 離地面遠） tall; high 2 （在一般標準或平均程度之上; 等級在上的） above...
  • 頻 : Ⅰ形容詞（次數多） frequent Ⅱ副詞（屢次） frequently; repeatedly Ⅲ名詞1 [物理學] （物體每秒鐘振動...
  • 激 : Ⅰ動詞1 （水因受到阻礙或震蕩而向上涌） swash; surge; dash 2 （冷水突然刺激身體使得病） fall ill fr...
  • 勵 : Ⅰ動 （勸勉） encourage; exert oneself Ⅱ名詞（姓氏） a surname
  • 高頻 : high frequency
  • 激勵 : 1 （激發鼓勵） encourage; impel; urge; inspire; excite; stimulate; put one on one s mettle 2 [電...
  1. The experiment apparatus has been developed, which is based on software ( labview ) and hardware ( pci board ni 6024e ). the displacements and generative force at the tip of the ipmc actuators were measured with respect to the different voltages, frequents and various waveforms which include square, sinusoidal, and triangular wave

    實驗選取了不同電壓幅值，不同頻率的方波、三角波、正弦波三種波形作為電激勵信號，利用高速攝像記錄ipmc的位移變形，並通過力傳感器實測了ipmc試樣末端的輸出力。
  2. Its principle is : a laminated structure ( beam or plate ) with delamination consists of undelaminated region and delaminted region which can be divided to upper and lower parts. when a low - amplitude and high - frequency excitation has the frequency close to some part ' s natural frequency, this part will resonate and certain amount of mechanical energy will convert to heat so that the delaminated region ' s temperature exceeds greatly that of the undelaminated region. therefore the delamination can be located by means of infrared thermograph

    其原理是具有脫層的層合材料構件（梁或板）包含脫層區域及未脫層區域，脫層區域分為上下兩部分，若對層合材料構件施加小振幅、高頻率的振動激勵，當激勵頻率恰好接近其中一部分的固有頻率時，該部分就會產生共振響應，部分機械能將轉化為熱能，使脫層區域的溫度遠高於未脫層區域，藉助紅外熱像儀即可顯示出脫層的位置。
  3. For the negative uniaxial crystal material, the principal mode is a hybrid guided mode, which can also be excited by the light at any frequency, but when the single mode propagation condition can not be satisfied, some of the higher order hybrid guided modes will exist in the waveguide

    對于負單軸晶體，波導的主模是混合模hgm _ 0模，該模式同樣可被任何頻率的光波所激勵；當光波波長滿足一定條件時，波導內傳輸單模，否則，將激勵起高階混合模。
  4. The most achievement is that we firstly obtain the analytic accurate solution of the modal fields of the waveguide structure and find some available character : ( 1 ) the different uniaxial crystal materials have the different propagation properties ; ( 2 ) when the optical axis of the crystal is on the plane that is made up of the normal direction of the waveguide plane and the propagation, there are te mode and tm mode in this special waveguide, but the principal mode is different of the character of the uniaxial crystal, the principal mode is the principal mode of te mode for the negative uniaxial crystal, but the one of tm mode for the positive uniaxial crystal ; ( 3 ) when the crystal optical - axis parallel to the waveguide plane, for the positive uniaxial crystal material, the principal mode of the waveguide is a te wave, which can be excited by the light at any frequency ; when the light frequency satisfies a single mode propagation condition, there will be only the principal mode propagating in the waveguide, otherwise some of the higher order modes can be excited, which are neither te modes, nor tm modes, but the hybrid guided modes

    本文就是在此背景下，利用金屬波導和單軸晶體的一些特性，結合麥克斯韋方程組和波導的邊界條件，從三種不同的情況研究了光在對稱平面單軸晶體金屬波導（波導層是單軸晶體，兩個波導界面均為金屬）內的傳輸特性，其主要貢獻為，首次解析地得到了這種波導結構下模式場的精確解，並發現了一些有用的特性： （ 1 ）模式場的性質因單軸晶體的性質不同而異； （ 2 ）當單軸晶體光軸位於波導界面法方向與傳輸方向構成的平面內時，波導中傳輸te波和tm波，只不過其主模因單軸晶體的性質不同而異，當波導層介質為負單軸晶體時，波導主模是te波主模，而波導層介質為正單軸晶體時波導主模是tm波主模。 （ 3 ）當單軸晶體光軸位於波導面內時，對于正單軸晶體，波導的主模是橫電波te _ 0模，任何頻率的光波均可激勵該模式；當光波波長滿足一定條件時，波導內傳輸單模，否則，將激勵起高階模式，高階模即匪te波，也匪tm波，而是兩者耦合而成的混合模。
  5. It was increasingly put to work on tasks ranging from how to auction a radio spectrum to devising a better way of paying defence contractors than cost - plus contracts ( which create incentives for the contractor to be inefficient ) or fixed - price contracts ( which may result in overpaying )

    機制設計被越來越多地用於各種場合，包括設計無線電頻段拍賣機制、以及為防務合同設計更加合理的支付機制以克服成本加成合同（會產生消極怠工的激勵）或固定價格合同（會導致給價過高）的弊端。
  6. Principal conclusions were drawn as the following : the non compatibility of pressure or velocity of the gas on both sides of the contact surface is the cause of the formation of shock wave ; the heating effect of reflective shock wave to driving gas during charging or exhausting process is the internal mechanism of peak oscillating effect, and all the factors that influence the formation and the running of the shock wave will influence the peak oscillating frequency, cooling effect

    主要結論如下：熱分離機內激波形成的原因是射氣瞬間接觸面兩側壓力和速度不相容；峰值振蕩效應的內在機制為反射激波對充氣階段的驅動氣或低溫排氣的加熱，凡是影響激波形成及運動的因素都將對峰值振蕩頻率、冷效應及熱效應產生影響；當充、排氣時間比為0 . 1763時，最佳射流激勵頻率出現在高階峰值振蕩頻率上。
  7. Through studying the working mechanism of the composing, the paper referred the bearing ' s analyzing model and designing flow. through shearing test of high damping rubber, the paper analyzes the influence of shearing shape, shearing strain range and inspiriting frequence on the characteristic parameters ( dynamic shear elastic module, dissipation engineering module, wasted gene ). according to the rule of equivalent energy, the paper gets the hysteretic curve of hdr ' s equivalent bilinear model and parameters ' calculating formula

    本論文通過對這種分離式減震支座各組成部分工作機理的研究，提出了該分離式減震支座整體的計算分析方法和設計流程；通過高阻尼橡膠剪切試驗，分析了高阻尼橡膠剪切面形狀、剪應變幅值、激勵頻率和試件高度對特徵參數（動態剪切彈性模量、耗能模量、損耗因子）的影響。
  8. So the pipe system sends out noise because of resonance. especially the frequency 250hz of pulsating water is in close proximity to natural frequency of pipe, so the 250hz is a dangerous frequency to the pipe system. there is another reason why the noise is reached to 110db ( a ) in pump room that the noise is magnified by the cistern because of the resonance of cistern

    特別是激勵頻率為250hz的頻率分量恰好與管道系統的固有頻率相接近，其引起的管道振動對噪聲的貢獻最突出，同時也與水泵房房腔的固有頻率相接近，從而引起房腔共鳴發聲，使噪聲進一步被放大，以至於噪聲最大處高達105db （ a ） 。
  9. It was indicated that the major frequency of signals for three different motivating manners concentrated between 20 and 50 khz, the difference between wavelet coefficients was small, and the pertinence of the original signal and the returning signals was low

    最終結果表明，從頻譜上來講，三種激勵方式所產生信號的主頻集中在20 50khz ，小波系數相差甚微，並且來源於同一源的接收信號與源信號相關程度也不高。
  10. Analysis software. the analysis show : the gyroscope effect to the flywheel rotor ' s and the shaft ' s vibration character under high rotate speed should be considered. at this time, the system ' s normal frequency is the function of rotate speed ; the amplitude passing through the resonance field can be lowered obviously by improving the effective damping of the electro - magnetic bearing

    建立了高速旋轉狀態下，採用磁軸承作支撐的飛輪轉子和轉軸的動力學模型，給出了有限元法在此問題中的具體應用，並利用i - deas有限元分析軟體具體分析了飛輪系統的共振頻率、系統振型，以及對偏心激勵的響應，分析表明：對于高速旋轉的飛輪轉子和轉軸，應考慮陀螺效應對其動力學特性的影響，此時系統的固有頻率是轉速的函數；通過提高磁軸承的等效阻尼可顯著降低系統通過共振區域時的振幅。
  11. Data of response of three high - pressure transducers are acquired respectively with effect of gas - shock tube and quick - opening valve. dynamic characters of transducers are known fully because of complementarity of data when transducers are calibrated at different frequency bands and pressure ranges. characteristic of excitation signal and its influence for modeling are discussed in this paper

    將三種高壓傳感器在氣體激波管和快速閥門上分別得到激勵響應的數據，根據兩者所能校準的頻率段和壓力范圍不同，利用數據的互補性，可以對傳感器的動態特性有全局的了解。
  12. The rf discharge excited waveguide co2 laser has been the suitable light source of lidar, because of its low volume, high efficiency and the particular wavelength

    由於射頻激勵波導co _ 2激光器體積小、效率高、調諧范圍寬、波長正處于大氣透射窗口等獨特優勢，它已成為激光雷達等應用的理想光源。
  13. Experiments are mainly focused on initial growth of unsteady primary instability, high frequency secondary instabilities both in natural condition and artificial high frequency excitation

    重點研究了基頻不穩定性擾動的初始增長過程，以及自然條件下與人工高頻激勵下的高頻二次不穩定性擾動發生與發展的一些特性。
  14. Perhaps the difficulty is how to build a im model which not only can work at common state but also can embody the high - frequency characteristic. in this thesis, we build two different parts separately to realize two different states, but we use speed, angle of flux and son on to connect them into one model

    主要原因是該方法所需的異步電機模型相當復雜：首先該模型能在基波條件下工作，實現基本的機電能量轉換，其次該模型還要對高頻信號進行響應，體現出高頻激勵下d - q軸阻抗差異特性。
  15. Actually to ensure the effect of soft - contact continuous casting, the power input should be increased to compensate the decrease in exciting current if the frequency increases

    在實際生產中，如果需要提高電源輸入頻率，則應該同時適當的增大電源功率來彌補激勵電流的減小，以保證軟接觸效果。
  16. The clash of interests cannot be avoided channels of hntv have no co - operations. considering self - interests, each professional channel makes use of limited capital to operate as a compositive channel. so similar programs on each professional channel bring about resource waste and increase of cost

    湖南電視臺屬下的專業頻道各自為政，都以有限的資源走綜合頻道之路，導致節目雷同、重復建設浪費突出、管理成本加大；經營模式單一，沒有形成多渠道產出的產業鏈；沒有建立一套科學的質量控制體系，節目品牌化程度不高；人才激勵措施不力。
  17. None but is the test spectrum abundant and controllable, it is possible to simulate the stresses environment needed for exposing weakness of the product. based on summarizing the present status of the vibration test and vibration environment simulation technology in the world, the topic of simulation of super - gaussian random vibration environment with controllable frequency spectrum and its applications in reliability enhancement testing is put forward. the main content and conclusions of the dissertation are as following : 1

    本文在綜述國內外振動試驗技術和振動環境模擬技術的基礎上，引出「頻譜可控的超高斯隨機振動環境模擬技術及其在可靠性強化試驗中的應用」這一主題，並緊緊圍繞該主題開展了如下研究工作: 1 .全面分析了振動激勵的功率譜密度量級、幅值分佈、帶寬以及試件結構的固有頻率、阻尼比等因素對疲勞損傷累積的強化效應，提出振動強化試驗激勵信號應具備的重要特性:頻譜可控和超高斯，確立了本文的研究主題和方向。
  18. Stochastic resonance ( sr ) is a counterintuitive phenomenon of nonlinear dynamic systems wherein the noise ( stochastic force ) plays a constructive role. this phenomenon has then attracted much attention in the past two decades, and it has been observed that sr can occur in a wide variety of systems

    隨機共振現象是非線性動力學系統中的一種反直觀的現象，當一個非線性動力學系統受到一個隨機力（噪聲）的激勵，也就是系統輸入具有一個連續的頻譜，系統和輸入的隨機激勵之間會產生一種協同作用，使得系統輸出的性能有所提高，這一現象被稱為隨機共振。
  19. The approach that dds excites pll is used to realize the more stable and accurate uhf frequency synthesizer in a proper bandwidth in this paper

    本文採用dds激勵pll的方式，研究並設計一種uhf波段高穩定度、小步進跳頻的頻率合成器。
  20. Moreover, multiple frequency stimulation method can increase consumption of ic obviously and surface diffuse reflection method can improve surface emission coefficient of ic availably

    混和信號激勵法能明顯增大三極體放大電路耗散功率，特別是第一級耗散功率；增頻激勵法能有效提高ic耗散功率；表面漫射法能有效增大元器件的發射系數。
分享友人
分享到 Line

分享到臉書