點焊接頭 的英文怎麼說
中文拼音 [diǎnhànjiētóu]
點焊接頭
英文
button weld-
Welding and allied techniques. spot, projection or seam welded lap joints
焊接和有關技術.點焊凸焊或縫焊搭接接頭Welding and allied techniques. resistance spot, projection and seam welded lap joints. tension shear tests
焊接及相關技術.電阻點焊凸焊和滾焊搭接接頭Our mylar sleeves are mainly used to protect a wide range of electrical equipments, such as thermal protectors, temperature limiting switches, refrigerant compressors, rechargeable batteries, fuses, transformers, motors, electrical wires, electrical ? heating elements, capacitors, telephone relay, soldered dot, tie - in and winding, etc
我們的聚脂套管主要用於熱保護器、高溫控制開關、製冷壓縮機、充電電池、保險絲、變壓器、馬達、電線、電器元件、電容、電話繼電器、焊點、接頭、線圈等耐絕緣及機械保護。Method of macro test for section of spot welded joint
點焊接頭截面肉眼檢測方法Backing weld procedure technique of all - position narrow gap and thick - walled pipe welding is developed about all - position single - pass welding section analysis, wire feeding behavior, weld arc length, welding current analysis, procedure and joint test. the achievement has general guide meaning to producing and testing all - position welder
從單焊道全位置區段、送絲行為、焊接弧長(電壓) 、電流行為分析、工藝試驗和接頭檢驗等幾方面介紹管道全位置打底焊工藝特點,其研究成果對全位置焊接機的製造和調試具有普遍指導意義。Abstract : backing weld procedure technique of all - position narrow gap and thick - walled pipe welding is developed about all - position single - pass welding section analysis, wire feeding behavior, weld arc length, welding current analysis, procedure and joint test. the achievement has general guide meaning to producing and testing all - position welder
文摘:從單焊道全位置區段、送絲行為、焊接弧長(電壓) 、電流行為分析、工藝試驗和接頭檢驗等幾方面介紹管道全位置打底焊工藝特點,其研究成果對全位置焊接機的製造和調試具有普遍指導意義。Based on the construction of guangzhou metro line 3 welding process and quality control, this paper introduces the mobile contact welding, analyzes some key points during the process of welding, such as welding of rails in curved sections, environmental protection, the measurement of straightness on the welding junctions located in curved sections, the maintenances of equipment etc., holds that more attention shall be given to these points
摘要介紹了移動式接觸焊在廣州地鐵3號線中的施工工藝及施工過程;分析施工過程中應該注意的曲線鋼軌焊接、環境保護、曲線鋼軌焊接接頭平直度的測量、設備維修保養等技術要點。Method of fatigue testing for spot welded joint
點焊接頭疲勞試驗法Resistance spot welding - destructive tests of welds - method for the fatigue testing of spot welded joints
電阻點焊.焊接有損試驗.點焊接頭的疲勞試驗方法Resistance spot welding - destructive tests of welds - method for the fatigue testing of spot welded joints iso 14324 : 2003 ; german version en iso 14324 : 2003
電阻點焊.焊接的有損檢驗.點焊接頭的疲勞試驗方法Resistance spot welding electrode adaptors
電阻點焊電極接頭Railway rolling stock. art and resistance welded joints of steels. part 1 : acceptance criteria for defects in welded butt and corner joints
鐵路車輛.鋼的電弧和電阻焊接接頭.第1部分:對接焊點和角焊接點中缺陷的驗收準則Comparison of c - scan of entire sample and the date of local point a - scan collected and processed with the metallorgaphs of sample cross section showed that the method could be used to determine the spot size of resistance spot welding
對接頭焊點的c掃描及對局部點的a掃描信號的採集與分析,經負際焊點橫截面的金相觀察對比,可以較準確確定點焊的焊核直徑。Railway rolling stock - spot welded joints of mild steel - design methods
鐵路車輛.低碳鋼點焊焊接接頭.設計方法Ultrasonic wire bonding was applied to connect the contacts and sub - miniature - a ( sma ) connectors. also a suitable shield box has been designed for the test of hts filters
對于超導濾波器的焊接,採用超聲點焊焊接sma的接頭和高溫超導濾波器的接觸電極,實現了較小的接觸電阻和較好的機械強度。Specification for resistance spot welding - electrode holders - morse taper fixing
點焊設備規程.電極夾具.第2部分:莫氏錐形接頭From review of quality manual and process control documents, write the code of lpm, and provide file of lpm on, discuss establishing of quality control examine system, emphases on key process examine and control and based on the demonstration of welding control, draw the conclusion of the importance of quality control
從修訂質量手冊和程序文件、編寫遼化機械廠標準和下發廠紅頭文件三個方面進行標準制定和貫徹。從建立健全質量考核機制、對影響產品質量的關鍵環節進行重點考核和遼化機械廠焊接質量考核實證分析,得出繼續抓好質量考核的重要性的結論。The question of ultra - sonic inspection on weld defect detecting of net frame spherical shape contact point is introduced in this paper, the detected rate of weld defect of net frame spherical shape contact point was significantly increased by improving the ultra - sonic exploring block, ultrasonic sensitivity special standard reference block and reference block, and ultra - sonic inspection process method
摘要介紹了超聲波探傷技術在檢測網架球接點焊縫缺陷中存在的問題;通過對超聲波探頭、靈敏度專用標準當量試塊和參考試塊以及超聲波探傷工藝等的改進,提高了球接點網架焊縫缺陷的檢出率。Study on the pitting corrosion resistance of butt resistance welds of stainless steels
不銹鋼電阻對焊接頭的抗點蝕性能研究Welding and allied processes. radiographic testing of resistance spot and seam welded joints. recommended practice
焊接和相關工藝.電阻點焊和滾焊接頭的射線照相檢查.推薦實施規程分享友人