齒側間隙 的英文怎麼說

中文拼音 [chǐzhāijiānxì]
齒側間隙 英文
backlash in circular tooth
  • 齒 : Ⅰ名詞1 （牙; 牙齒） tooth 2 （物體上齒形的部分） a tooth like part of anything 3 [書面語] （年齡...
  • 側 : 側形容詞[方言] （傾斜; 不正） slant; sloping
  • 間 : 間Ⅰ名詞1 （中間） between; among 2 （一定的空間或時間里） with a definite time or space 3 （一間...
  • 隙 : 名詞1 （縫隙; 裂縫） crack; chink; crevice 2 （空閑） gap; interval 3 （漏洞; 機會） loophole; op...
  • 間隙 : （空隙） interval; gap; freedom; space; [機械工程] clearance; separation; stricture; clear; inter...
  1. Based on the fact of driven gear moving prior to normal locality when driving gear pair moving from upper dead center to lower dead center, considering all influential elements, the maximum backlash of gear pair can be controlled to satisfy the special driving requirement through controlling the length and deviation of its common normal without increasing its manufacture precision

    摘要根據換向傳動齒輪副從上止點向下止點運動時被動齒輪運動超前的實際，從影響齒輪副側隙的各種因素出發，在不提高齒輪副製造精度的前提下，通過拉制齒輪副公法線長度及其偏差從而有效地控制齒輪副的最大齒側間隙，以滿足傳動的特殊要求。
  2. Abstract : the flying shear located behind the roughing stands of wire - rod mill is designed with hard surface gears for driving system, engaging of zero tolerance, hydraulic cylinder for clamping and shiftting, convenient and practical gap adjusting structure for blade

    文摘:介紹了邯鋼三軋廠在線材軋機粗軋機組后的飛剪設計中，採用了硬齒面齒輪傳動，零側隙嚙合，液壓缸鎖緊與橫移及簡便實用的剪刃間隙調整機構。
  3. 3. the trapping characteristics of ordinary helical gear pump are lucubrated by theory for the first time, the theoretic relation of the gear rotor between the end overlap coefficient and trapping phenomenon is discussed respectively with clearence or without clearcence, and the relation of trapping volume with the rotational angle turn is also discussed. the selective range of the helical angle that can eliminate completely the trapping of helical gear pump is gained, which never appeared in literature before

    首次對普通斜齒齒輪泵的困油特性進行深入的理論研究，分別討論了有側隙和無側隙時普通斜齒齒輪泵轉子的端面重合度與困油現象之間的理論關系，以及困油容積隨轉角的變化關系，得到了完全消除斜齒齒輪泵困油沖擊的螺旋角機械科學研究院博士學位論文的選擇范圍。
  4. This paper develops a mathematical model for the solution to the longitudinal tooth curve of an internal gear shaver based on the simplified principle for space transmission of a helical gear pair without flank clearance, and proposes a calculating approach of the profile modification of the grinding wheel to be used for grinding the longitudinal tooth curve of the shaver

    摘要用簡化的空間螺旋齒輪作無側隙嚙合傳動的原理，建立了求解內剃齒刀齒向曲線的數學模型，並給出了修磨這種齒向曲線的盤形砂輪的廓形計算方法。
  5. In this paper, we designed the structure of the gear and rack in this actuating mechanism, elaborated the theory of its formation, and deduced the profile function and gearing function of the gear and rack. furthermore, we deduced the inherent radius of going around a turn under certain circumstance, the condition of the correct gearing and the continuous transmission. in order to make the mechanism move steady, we designed the derivation mechanism and manufacture the modle

    本文對該傳動機構中的漸開線柱齒鼓形齒輪和空間齒條的結構進行了設計，並給出了齒輪和齒條的成型原理，推導出了漸開線柱齒鼓形齒輪和空間齒條的齒廓參數方程、嚙合方程;進一步分析並確定了漸開線柱齒鼓形齒輪、空間齒條在給定嚙合傳動條件下所能實現的固有轉彎半徑和運動約束條件，並對其側隙及效率進行了計算和分析。
  6. Backlash in circular tooth

    齒側間隙
  7. Calculation of the normal side gear clearance of internal - engaging involute gear transmisson

    內嚙合漸開線直齒輪傳動法向齒側間隙計算
  8. Circular metal slitting saw blades ; tooth forms, side clearance, manufacturing tolerances

    金屬用開槽圓盤鋸片.齒形側面間隙製造公差
分享友人
分享到 Line

分享到臉書