齒條加工 的英文怎麼說
中文拼音 [chǐtiáojiāgōng]
齒條加工
英文
rackwork-
The water current flows over the top of the dentoid baffle to the hydraulic jump as additional momentum. while it is cooperated with a stilling basin, the flowing condition emerged in the basin may be improved greatly and the length and downstream water depth required by the basin can be decreased to a great extent. such an appliance may be also used to solve the problems of insufficiently dissipating water flow energy and aerating flow, which are often faced with those hydraulic engineering constraction as acted by high waterhead, great specific discharge and low froude number
本文通過齒墩頂部的擴散水舌所形成的附加射流，從上部射入水躍，即可改善消力池內的水流流態，又可降低第二共軛水深，減小水躍長度，增進水躍消能效果，同時還能解決大單寬、低佛勞德數條件下摻氣和消能不足的問題，試驗證實它是一種安全、經濟的消能工。Results : 1 ) under the same condition of loading, the stress and displacement of mesial occlusal rest design was smaller than that of distal occlusal rest design in abutment teeth and soft tissue under the base, however, the magnitude in the soft tissue under base was bigger. 2 ) when a distributed vertical load was applied to the artificial tooth abutment teeth regions, the stress distribution was similar to that of concentrated load in the artifitial tooth, and stress magnitudes were higher. 3 ) under the condition tested, the mesial occlusal rest design caused the stresses that were more in line with the long axes of the abutment teeth than did the distal occlusal rest design
結果： 1 ）在同一加載條件下，近中（牙合）支托設計與遠中（牙合）支托設計相比，基牙及基托下軟組織的應力和位移值減小；基托下軟組織的應力和位移值大於基牙； 2 ）基牙及義齒整體加載時，各基牙應力分佈規律與人工牙加載相同，但應力值增大； 3 ）近中（牙合）支托設計使基牙受力更趨于軸向。Abstract : requirements for hydraulic steering rack cylinder are very high, the rack cylinder should be durable, lubricants preservable and of seal. so, finish machining and parameter - set are necessary
文摘:液壓轉向機對齒條桿部表面有很高的耐磨、儲油、封存要求，為此需要一套表面超精加工工藝及加工參數設定。Witch has worked out the tooth shape of datum rack and computer simulation of gear manufacture. pointedness, undercut and tooth tip becoming sharp are analysed. tooth thickness calculation and measurement, superposition coefficient calculation and belt length calculation are resolved
2 、給出了基準齒條的齒廓形狀，進行了齒輪加工計算機模擬，分析了可能出現的稜角問題，進行了齒輪內齒頂圓的求解、根切問題分析、齒厚計算與測量、齒頂變尖的分析、重合度的計算、帶長度的計算及齒輪設計的程序編制等。Through analysis of the change of the specifications of the clothing wires made of alloy steel before or after the tempering process, the paper puts forth that installation of tempering device after the punching and quenching process is helpful to better quality of clothing wires, improving the color difference of clothing and prolong the service life of clothing
摘要通過分析合金鋼針布齒條回火前後各項指標的變化，指出在沖淬工藝后加裝回火裝置有助於提高金屬針布性能，改善針布齒條色差，延長其使用壽命。The qijiang count gathered the large quantities of forgings, the gear, the part always becomes the production enterprise, the forging production, the machine - finishing, assemblies and parts technology is advanced, the condition was superior
綦江聚集了大批鍛件、齒輪、部件總成生產企業，鍛造生產、機械加工、總成裝配技術先進，條件優越。Woodworking machines. acceptance conditions and nomenclature for vertical band saws. ripsaws and split saws
木材加工機械.立式帶鋸床的驗收條件和術語.縱割鋸和粗齒鋸The points of internal gear are fitted into spline curve by spline function, then the internal gear is manufactured in nc wire - cut machine. the process of manufacturing the internal gear in wire - cut machine is studied. compared to the traditional method of manufacturing in special machine this process is a breakthrough
利用樣條函數對中心輪內齒圈齒形點進行擬合，利用軌跡法在數控線切割機床（ bkdc ）上實現了中心輪內齒圈齒形的加工，並對在數控機床上加工的工藝進行了研究。The two key factors, machining methods and machine - setting parameters of sbg, which are related with the generation of theoretical tooth surface and topographic deviation for sbg, are analyzed in details. after building the machine - tool mathematical model and computing the tooth surface parameters, using the given conditions and mesh equation, the coordinates of the theoretical tooth surface of sbg can be computed, and, then, the theoretical tooth surface model of sbg is derived
本文詳細地分析了形成螺旋錐齒輪理論齒面及產生拓撲誤差的兩個關鍵因素，即螺旋錐齒輪的切齒加工方法和機床調整參數;通過建立機床數學模型，計算齒面參數，用已知條件和嚙合方程進行聯合求解，得出了理論齒面的坐標值，從而獲得了螺旋錐齒輪的理論齒面模型。Adopting high precision rack driving, it has advantages of faster speed, stable operation, strong strength and large power. it is suitable for processing of largescale advertisement products and wooden products. in addition, the dust collector and the suction device are available for option
用高精度齒條傳動，速度更快，運行平穩，力度強，功率高，適合大型廣告製品，木工產品的加工，另有吸塵、吸附裝置供選配。The necessary and sufficient conditions for the input angle to be rotatable angle of n - bar linkages and the rotatability of five - bar are firstly proved according to the theory of n - bar linkages. then we conclude the five - bar ' s classification and the gear ratio and phase angle in each classification to be full rotatability. according to the algorithm, with the tool of visual c + + 6. 0, 1 developed a set of intelligent software to dynamically create geared five - bar ' s locus curves and velocity and acceleration curves, achieve the visualized input
根據該條件所得到的演算法，以windows為平臺，以面向對象的visualc + + 6 . 0為開發工具，開發了一套智能化的齒輪?五桿機構的軌跡生成軟體系統，實現了機構參數的可視化輸入、機構的軌跡曲線、速度和加速度曲線的動態生成，從而實現了齒輪?五桿機構軌跡曲線的動態模擬。分享友人