齒輪公差 的英文怎麼說

中文拼音 [chǐlúngōngchā]
齒輪公差 英文
gearing tolerance
  • 齒 : Ⅰ名詞1 （牙; 牙齒） tooth 2 （物體上齒形的部分） a tooth like part of anything 3 [書面語] （年齡...
  • 輪 : Ⅰ名1 （輪子） wheel 2 （像輪子的東西） wheel like object; ring; disc 3 （輪船） steamer; steamboa...
  • 公 : Ⅰ形容詞1 （屬于國家或集體的） state owned; collective; public 2 （共同的;大家承認的） common; gen...
  • 差 : 差Ⅰ名詞1 （不相同; 不相合） difference; dissimilarity 2 （差錯） mistake 3 [數學] （差數） differ...
  • 齒輪 : gear [rack; toothed] wheel; （toothed） gear; wheel gear
  1. Tolerancing of bevel gears ; basic concepts

    傘齒輪嚙合公差.第1部分:基本概念
  2. In this paper, the relation between differential driven ratio accuracy and the common normal length error of cylindrical bevel wheel has been found by experimental method, which provides a efficient way for cylindrical bevel wheel manufacturer to control the common normal length error of the wheel

    摘要通過實驗研究，尋找出差動傳動比的精度與斜齒圓柱齒輪的公法線長度誤差的關系，從而為斜齒圓柱齒輪的加工提供一個可以控制斜齒圓柱齒輪公發線長度誤差的有效方法。
  3. Pinion - type cutters for cylindrical gears ; tolerances

    圓柱齒輪用插齒刀.公差
  4. The thesis developed the optimization design software of geometric parameter for the worm gear including strength check module, the drawing contact lines module, the change lines of tooth thickness of worm, and the parametric modelling software for the reducer which includes parametric modelling of parts and assembly. the cad prototype system is very convenient because of its accessible interfere, simple operation and written in chinese. by input design parameters ， the cad system can make optimization design and strength check for the worm gear ， draw contact lines of tooth flank of worm - gear and change line of tooth thickness of worm ， judge if the tooth flanks of worm undercut and if the sideward tooth of worm - gear hob come to a point ， make project design and structure design for the reducer and draw its 2d parts and assembly

    研究和開發了平面二次包絡環面蝸桿傳動的參數優化設計和校核軟體系統：包括幾何參數設計計算模塊，強度校核模塊，繪制齒面接觸線模塊，蝸桿齒厚變化曲線模塊和蝸桿根切判別模塊；開發了平面二次包絡環面蝸桿減速器外形與結構尺寸數據庫以及傳動效率數據庫，建立了平面二次包絡環面蝸桿傳動公差及極限偏差數據庫；開發了平面二次包絡環面蝸桿減速器參數化建模軟體：包括零部件的參數化建模模塊和裝配圖的參數化建模模塊，其中零部件的參數化建模包括蝸桿軸系的參數化建模、蝸輪軸系的參數化建模、箱體的參數化建模、端蓋的參數化建模、軸承的參數化建模和其它零部件的參數化建模軟體模塊。
  5. Tolerances for single - start hobs for involute spur gears

    漸開線正齒輪用單頭滾銑刀的公差
  6. Based on the fact of driven gear moving prior to normal locality when driving gear pair moving from upper dead center to lower dead center, considering all influential elements, the maximum backlash of gear pair can be controlled to satisfy the special driving requirement through controlling the length and deviation of its common normal without increasing its manufacture precision

    摘要根據換向傳動齒輪副從上止點向下止點運動時被動齒輪運動超前的實際，從影響齒輪副側隙的各種因素出發，在不提高齒輪副製造精度的前提下，通過拉制齒輪副公法線長度及其偏差從而有效地控制齒輪副的最大齒側間隙，以滿足傳動的特殊要求。
  7. This paper makes the design and inpect and measure and optimum design of double circular - arc gears as a whole system using actual design methods and technology

    本論文將雙圓弧齒輪的設計、校核、測量及精度與公差、優化設計很好地結合在一起，利用現代設計方法和技術，建立了一個完整的系統。
  8. Tolerances for gear hobs for fine mechanics

    精密加工裝置的齒輪滾刀的公差
  9. Deviations of shaft centre distances and shaft position tolerances of casings for cylindrical gears

    圓柱齒輪箱的軸距偏差和軸位公差
  10. Tolerances for cylindrical gear teeth ; tolerances for pitch - span deviations

    圓柱齒輪嚙合公差齒距偏移公差
  11. First, the basic theory of static load sharing mechanism has been presented, mainly including manufacturing and assembly error of each gear component ' s axis and each bearing ' s axis, gear size ( tooth thickness ) errors, simultaneous error of middle two - tooth. the formula of equivalent mesh error has been deduced, the load sharing coefficient has been computed. second, the influences of each error on the static load sharing coefficient have been discussed

    首先，從靜力學的角度研究了星型齒輪系統均載的基本原理；確定了影響齒輪系統均載特性的製造和安裝誤差，主要包括：各個齒輪構件的中心軸線製造和安裝誤差、軸承中心軸線的製造和安裝誤差、齒厚偏差、雙聯星輪同時嚙合線誤差；推導了這些誤差的當量嚙合誤差的計算公式，分析了系統的均載特性。
  12. The whole software is composed of four modules :, the scaling module, the hangingjgear, the process module. the three modules are independent, moreover they are interrelated, which make then arc - gear - capp is a whole process

    各個模塊既是獨立的，可以單獨調用其中的任何一個模塊；又是相互聯系的，構成一個整體，從而實現工藝規程的制定、機床掛輪的選擇、尺寸測量、精度與公差的選擇等完整的圓弧齒輪的加工過程。
  13. The load assignment formula and the method of the double circular arc gear under the wiring error influence between the contact mark was introduced and inferred

    摘要介紹並推導雙圓弧齒輪在安裝誤差影響下接觸跡間載荷分配的計算公式和方法。
  14. Tolerances for cylindrical gear teeth ; tolerances for tooth trace deviations

    圓柱齒輪嚙合公差.齒面線偏移公差
  15. The precision of the non - contact testing of flywheel gear ' s contour and location error of light electricity inspection machine based on virtual instrument has been carried on theory analysis in this paper. various contour and location tolerances of the part have been distributed depending on the result of the analysis, and the data handling method of measurement has been studied to find a data handling method of getting rid of the system error under one kind of condition of the big sample space

    本文對飛輪齒圈形位誤差光電檢驗機的精度進行了理論分析，依據分析的結果分配了零件的各種形位公差，並對測量結果的數據處理方法進行了研究，找到了一種在大樣本空間的條件下依概率排除系統誤差的數據處理方法，同時為了驗證其可靠度對其進行了計算機模擬實驗。
  16. Through analyzing the influence of the precision gearing system on dynamic and static quality of servo system, the calculation formula of transmission error and return difference have been further analyzed and the measures how to reduce them have been proposed

    作者在分析精密齒輪傳動裝置對伺服系統動態品質和靜態品質影響的基礎上，還進一步分析了傳動誤差、傳動回差的計算公式，提出了減小誤差的措施。
  17. Tolerance specification of gear hobs

    齒輪滾刀的公差規范
  18. Gears with round flanks for fine mechanics ; tolerances and permissible devations for wheel and pignon

    精密機械的圓齒面齒輪.第4部分:傳動輪和小齒輪的公差
  19. Tolerancing of bevel gears ; tolerances for shaft angle errors and axes intersection point deviations

    傘齒輪嚙合公差.第4部分:軸線夾角誤差及軸線交叉點偏
  20. System of gear fits ; backlash, tooth thickness allowances, tooth thickness tolerances ; principles

    齒輪配合體系.側隙齒厚容差和齒厚公差.原則
分享友人
分享到 Line

分享到臉書