齒頂高 的英文怎麼說
中文拼音 [chǐdǐnggāo]
齒頂高
英文
[機械工程] addendum; tooth addendum [head]齒頂高修正 addendum correction [modification]-
Addendum modification of external spur and helical gears
外嚙合圓柱齒輪和斜齒輪的齒頂高修正Addendum modification of straight spur gears in the 05 - system ; introduction
-系統的直齒正齒輪的齒頂高修正.導言The results indicate that if the value of press stress is over certain figure, press stress and al plate ’ s thickness have little influence on sawtooth distortion for the same kind of sawtooth ; sawtooth distortion is well - regulated under static press, while it is irregular under impact press. bottom coating make great influence on bond strength of samples which can improve the value remarkably ; bonding mechanism of clad steel is mechanism of mechanical effect that sawtooth which is hooked occludes with al plate
結果表明：同種齒型，當壓應力大於一定的值時，壓應力和覆板的厚度對齒形的變化影響不大；靜壓下齒形變化比較規則，鋸齒頂端向一側彎曲成鉤狀；沖壓下齒形比較凌亂，鋸齒的頂端沒有明顯的變形；后處理對試樣的結合強度影響很大，打底試樣由於粘結層的作用，結合強度較高；機械作用機制是復合鋼板的主要復合機理，鋸齒彎曲成鉤狀和鋁板形成機械咬合。Mean measuring addendum
中點測量齒頂高Equal addendum teeth
等齒頂高齒Geometrical design of cylindrical internal involute gear pairs ; diagrams for the determination of addendum modification coefficients
漸開線嚙合圓柱內齒輪副的幾何設計:齒頂高變位系數測After thoroughly analyzing the influence of each pump parameters on the gear pump performance, the paper developes the criterion for optimum gear parameters, which can be utilizied in practice easily for gear manufacturing using normal involute gear hob with two - fillet type. the conclutions studied by the paper are : 1. both the addendum coefficient and the deddendum coefficient of the pump gear should be 1. 125
以目前國內普遍使用的雙圓弧頭全齒高為2 . 5倍模數漸開線標準滾刀作為泵齒輪的加工刀具，通過對齒輪加工原理的分析，提出了欲使泵齒輪參數達到最佳，泵齒輪的齒頂高系數和齒根高系數都為1 . 125 ；對變位系數的確定應考慮到泵齒輪的根切、齒頂厚、重合度以及側隙因素；泵齒輪為避免過渡曲線干涉，必然要存在根切現象。Rake angle and senitopping can be made. it is a high effcient cutting tools
並可做成正前角或半切頂是一種高效的齒輪工具For cutting the composite lock gear with unequal tooth thickness, a study is made on the design method of gear sharper cutter with nonstandard parameter involute tooth profile and noninvolute tooth profile. the cutter tooth arrangement, the choice of teeth number of the cutter and the basic method of cutter design are discussed ; and a new method of choosing deflection factor by using limited area is presented. and the curve of relationship between rear angle on tooth crest and helical angle on tooth side of the cutter is given so as to give a basis for the gear sharper cutter to choose its parameters. to design nonstandard gear sharper cutter by adopting the method mentioned above will simplify the calculation and will increase the efficiency of design
研究加工不等齒厚的非標準參數漸開線齒形，與非漸開線齒形復合的鎖閉齒輪插齒刀刀齒的排列、刀具齒數的選擇以及刀具設計的基本方法，介紹用限制區域選擇插齒刀變位系數的新方法，並給出刀具齒頂后角與側螺旋角的關系曲線，為插齒刀參數的選擇提供依據.結果表明，採用上述方法設計非標準復合齒輪插齒刀，可簡化計算和提高設計效率Girded around with a wild boar ' s teeth, he shall climb over the mountain summits and higher than the shadow of the helmeted man
束縛圍繞著野豬的牙齒，他會攀登山峰的頂點，被帶頭盔的人的影子還要高。分享友人