龍門型起重機 的英文怎麼說

中文拼音 [lóngménxíngqǐzhòngjī]
龍門型起重機 英文
portal crane
  • 龍 : Ⅰ名詞1 [動物學] （古代傳說中的神異動物） dragon2 （古代巨大的爬行動物） a huge extinct reptile:恐...
  • 門 : Ⅰ名詞1 （房屋、車船等的出入口 ） entrance; exit; door; gate 2 （形狀或作用像門的東西） switch; va...
  • 起 : 起Ⅰ動詞1 （站起; 坐起） rise; get up; stand up 2 （取出; 取走） draw out; remove; extract; pull 3...
  • 重 : 重Ⅰ名詞（重量; 分量） weight Ⅱ動詞（重視） lay [place put] stress on; place value upon; attach im...
  • 機 : machineengine
  • 龍門 : gantry
  • 起重機 : crane; derrick; crab; freight elevator; hoist; lifter; cranage; hoister
  • 起重 : jack up起重臂 jib loading boom; cargo boom; erector arm; jibboom; 起重車 carriage hoist; crane ca...
  1. The ansys, a kind of fea program, was used to build model of small carriage. the procedure of gantry beam bump with secondary beam of bridge was reappeared by running nonlinear calculation and loading program which was written by apdl program language. the closest deforming result was gotten, and the deforming of main beam, secondary beam and end beam and inner stress distribution status were calculated

    採用大型三維有限元軟體ansys對該起重機以及小車架等進行了建模、應用apdl語言編寫加載程序、進行非線性計算，再現龍門橫梁與起重機副梁碰撞過程，最後得到與實際變形結果最接近的一種狀態，得出起重機橋架主梁、副梁、端梁的變形以及其內部的應力分佈情況。
  2. This paper discusses creative long - distance slippage and dragging technology based on the success in extra - wide, extra - high and extra - weight large portal crane transferring

    根據超寬、超高、超重的大型龍門起重機整機搬遷工程的成功實例，分析其具有原創意義的超長距離滑移拖曳工藝。
  3. This paper describes development and situation of container transportation and container terminal handling technologies and gives a brief presentation of the new twin trolley quayside container crane and rmg

    摘要結合集裝箱運輸和碼頭裝卸工藝發展的現狀，對新型雙小車岸橋和共軌式集裝箱軌道龍門起重機（ rmg ）作簡要的介紹。
  4. An application example provided for the application of finite element method in probability analysis. three main procedures are described for probability analysis in ansys. they are the form of the model files, procedure for probability analysis, postprocess and distill of results, so theories and practices are combined tightly in this paper

    第六章是有限元法在可靠性分析中的應用實例，以一臺龍門起重機為例，詳細描述了在有限元中進行可靠性分析的三個重要步驟:模型文件的生成、可靠性分析階段、后處理和結果的提取，因此本文將理論與實踐密切結合起來了。
分享友人
分享到 Line

分享到臉書