adams process 中文意思是什麼

adams process 解釋
亞當斯玻璃除鐵法
  • adams : n. 亞當斯〈姓氏〉。
  • process : n 1 進行，經過；過程，歷程；作用。 2 處置，方法，步驟；加工處理，工藝程序，工序；製作法。3 【攝影...
  1. In the adams software environment, the force of rocket launcher joint parts under the two sail conditions of transverse wave and oblique wave is calculated in the process of the servo system control motion

    用adams軟體求解了某火箭炮在橫浪和斜浪2種航行狀態下，以大正弦規律調炮時各連接部位的受力情況。
  2. The identified proteins are involved in a variety of cellular process including several zinc finger proteins relevant to transcription regulation, such as zinc finger 198, 263, 14, 224, zf6, novel protein similar to transcriptional represser ctcf, and kruppel - like zinc finger protein ; two members of the adams ( a disintegrin and metalloprotease domain ) family ; two members of integrin family ; several proteins involved in the signal transduction, cell - cycle control, chromatin remodeling and transcription repression ; and also some proteins of cell skeleton and some with unknown functions

    鑒定出的蛋白包括多個與轉錄調控相關的鋅指蛋白，如鋅指蛋白198 、 263 、 14 、 224 、 zf6 、轉錄抑制因子ctcf樣蛋白、幻肚pple樣鋅指蛋白等:兩個含金屬蛋白酶結構域和整合素結合結構域的家族成員adam28和adam17 ;兩個整合素家族成員pz整合素和含十個egf樣結構域的整合素（ tied ） ;與細胞信號轉導通路有關的蛋白;與細胞周期調控有關的蛋白;與染色體重塑和基因轉錄抑制有關的蛋白;細胞骨架蛋白以及其他功能未明的蛋白等。
  3. On the base of achievements of predecessors, this thesis use a new research method - adams software. using the software, i built simulating model of 3s clutch, and study the engaging and disengaging of 3s clutch during codog translating process. combined with experimental results, i make deeper research, and make some achievements

    在以往研究成果的基礎上，本文採用了新的研究方法，用先進的動力學模擬軟體? ? adams軟體，建立了3s離合器的模擬模型，對codog切換過程中3s離合器的嚙合和脫開過程進行了模擬研究，與實驗結果結合起來后進行了深入的分析，取得了一些成果。
  4. In this paper, dynamic analysis for landing gear landing is conducted for a large transportation aircraft, and dynamic equation of landing gear during landing process was established. the mathematical model and dynamic simulation of landing gear was established in the software adams

    本文以某大型運輸機起落架為研究對象，建立了起落架著陸動力學方程，應用adams軟體對該起落架進行建模和被動控制下的著陸動態模擬，得到了相關的參數曲線。
  5. First of all, it introduces the process of applying pro / e and adams to simulate. whereafter, it builds the three - dimensional model of centralizer in pro / e, and transmits it to adams by the interface software mechanism / pro. and then, it tests and validates the virtual prototyping and performaces the kinematic simulation

    對扶正器在進行虛擬樣機技術模擬時，本文完成了如下的工作:首先介紹了利用pro / e和adams聯合模擬的流程，然後按照模擬流程在pro / e環境下建立了扶正器的三維模型，將其通過介面軟體mechanism / pro處理后導入到adams環境中，接著在adams中對虛擬樣機進行了調整和驗證，並對扶正器虛擬樣機進行了運動學模擬。
分享友人
分享到 Line

分享到臉書