air circuit resistance 中文意思是什麼

air circuit resistance 解釋
空氣循環阻力
  • air : n 1 空氣，大氣。2 天空，空中。3 微風，和風。4 態度，樣子，風度，氣派；〈pl 〉高傲的架子。5 傳播，...
  • circuit : n 1 （某一范圍的）周邊一圈；巡迴，周遊；巡迴路線[區域]；迂路。2 巡迴審判（區）；巡迴律師會。3 【...
  • resistance : n. 1. 抵抗，反抗，抗拒，抵禦；敵對，抵抗力，反抗力，阻力，【生物學】抗病性。2. 【電學】電阻；阻抗；電阻器。
  1. The control system of furnace " s temperature has been widely used in every walk of life, as an important link of repair and manufacture of the electrical equipment such as electromotor transformer etc., soaking lacquer drying craft has some especial requests on drying crafto this article starts with the analysis of drying chamber " s configuration, analyzed its configuration limitation and control function limitation according to the factory " s situation and advances the conception of heated air drying circulation, in addition, this article adopts an intellectualize a / d module, a development sampling tuning - voltage circuit, and presents the method to measure online the insulation resistance of products in order to improve constantly products quality

    而浸漆乾燥工藝作為電機、變壓器等電氣設備的修理、製造中的重要環節之一，對乾燥過程的質量要求有一定的特殊性。該文從乾燥爐的結構分析入手，聯繫到工廠的實際情況分析了結構功能缺陷和控制功能缺陷，提出了熱風循環乾燥的概念，同時，選擇了較為先進的a d板卡、熱電阻信號調理板等專業化智能卡，運用數字pid控制技術，構成了一個較有特色的計算機控制系統。此外，該文還從保證乾燥品質量的角度，採用智能化交流模塊和自製采樣調壓電路的方法，提出了在線檢測產修品的絕緣電阻的方法和手段，以確保企業產品質量不斷提高。
  2. Air circuit resistance

    空氣循環阻力
  3. In this system, mean velocity pipe is applied to transform the air velocity signal into pressure difference signal, and then the pressure difference signal is input into pressure difference transmitter to realize the transform of the pressure difference signal from non - electricity signal to electric current, and through the resistance in the corresponding sampling circuit the electric current is transformed into voltage signal ; the thermocouple is used as the primary element to realize the transform from temperature signal to the voltage signal ; under the control of communication agreement module, diversified voltage signal is transported into computer by way of a / d conversion module, and then the monitoring software compiled beforehand is transferred to deal with all the voltage signals relatively, the result of which is conveyed to relative interface to display

    該裝置具有三個特點：一是採用表面式測溫方法，有效地減少了元件的維護與損耗；二是採用工業控制計算機及信息就地採集、數據總線傳輸的方式，充分利用計算機和數據自動採集方面的技術，實現各種參數的在線測量，監測指標全面，能與dcs系統聯用，具有技術先進性和一定的前瞻性；三是採用顯示器配工業觸摸屏的顯示方式，為現場運行人員提供了簡單、易學、方便的操作模式。本裝置自2001年8月投入運行以來，有效地幫助、指導運行人員進行燃燒調整，對于鍋爐和機組的安全、經濟運行發揮了重要作用。
  4. On - line monitoring of hvcb is the precondition of predicting maintenance, is the key element of reliable run, and is the important supplement to the traditional off - line preventive maintenance in fact, the faults are made by hvcb, no matter in number or in times, is over 60 % of total faults so it has determinative importance for improving the reliability of power supply and this can greatly decrease the capital waste used by - dating overhaul in this paper, the inspecting way of hvcb mechanism characteristic is discussed the concept of sub - circuit protector is presented, the scheme that we offered has been combined with sub - circuit integrality monitoring theory, to ensure that it has the two functions as a whole according the shut - off times at rated short circuit given by hvcb manufacturer, the electricity longevity loss can be calculated in each operation, and the remained longevity can be forecast too an indirect way for calculating main touch ' s temperature by using breaker shell temperature, air circumference temperature and breaker ' s heat resistance is improved in this paper, and main touch resistance can be calculated if providing the load current msp430, a new single chip microcomputer made by ti company, is engaged to develop the hardware system of the on - line monitoring device, and special problem brought by the lower supply voltage range of this chip is considered fully

    高壓斷路器所造成的事故無論是在次數，還是在事故所造成的停電時間上都占據總量60以上。因此，及時了解斷路器的工作狀態對提高供電可靠性有決定性意義；並可以大大減少盲目定期檢修帶來的資金浪費。本文論述了斷路器機械特性參數監測方法；提出了二次迴路保護器的概念，並將跳、合閘線圈完整性監視和二次迴路保護結合起來，給出具有完整性監視功能的二次迴路保護器實現方案；根據斷路器生產廠家提供的斷路器額定短路電流分斷次數，計算每次分閘對應的觸頭電壽命損耗，預測觸頭電壽命；提出根據斷路器殼體溫度和斷路器周圍空氣溫度結合斷路器熱阻來計算斷路器主觸頭穩態溫升的方法，並根據此時的負荷電流間接計算主觸頭迴路的電阻；在硬體電路設計上，採用美國ti公司最新推出的一種功能強大的單片機msp430 ，並充分考慮該晶元的適用電壓范圍給設計帶來的特殊問題；在通信模塊的設計中，解決了不同工作電壓晶元之間的介面問題，並給出了直接聯接的接線方案。
分享友人
分享到 Line

分享到臉書