angle error analysis 中文意思是什麼

angle error analysis 解釋
角誤差分析
  • angle : n 【英史】盎格魯人〈cf Angles〉。n 1 角，隅，角落；棱，嬗角。2 【數學】角，角位，角的度數。3 【機...
  • error : n. 1. 錯誤；失錯。2. 謬見，誤想；誤信；誤解。3. 罪過。4. 【數學】誤差；【法律】誤審，違法；（棒球中的）錯打。adj. -less 無錯誤的，正確的。
  • analysis : n. （pl. -ses ）1. 分解，分析；【數學】解析。2. 梗概，要略。3. 〈美國〉用精神分析法治療（＝ psychoanalysis）。
  1. The paper also does some deep research on the mesh characteristic of the mechanism, analyses the cause o f the cam profile error and index error during working, using object - oriented method, vc + + and pro / toolkit, performs second development to pro / engineer, completes entity proplasm of the cam mechanism using only few parameters, the press angle calculate module, error analysis module and curvature calculate module are built on the basis of it

    然後通過對弧面分度凸輪加工中產生廓面誤差及工作時產生分度誤差原因的分析，建立了計算加工和分度誤差的數學模型。應用vc + +和pro toolkit對pro engineer進行二次開發，建立了弧面分度凸輪機構的參數化設計和三維造型及壓力角、誘導主曲率等運動特性和誤差分析軟體系統。
  2. The model of influence upon the parallel between servo optic axis from the angle error of installation plans presented. whereby the theoretic analysis is carried out and the analyzing results are obtained. the method of obtaining the angle error through measuring the installation plans with three - coordinates measuring device and fitting the measurement data is put forward and pave a road for lessening the influence

    對安裝面角誤差影響隨動光軸平行性的問題也建立了數學模型，以此為出發點進行理論分析，給出了分析結果；提出用三坐標測量機測量安裝面，通過擬合得到安裝面的角誤差；從而為減小這一誤差源對隨動光軸平行性的影響鋪平了道路。
  3. After the construct of the motion simulation model, genetic algorithm is used to do the adjustment of pid parameters of the control system of the joint motors, integral separation pid control and angle error analysis is finished, and three force / torque sensors, touch sensors, distance sensors and photoelectric switches are calibrated and installed

    在建立了機器人關節控制系統模型后，使用遺傳演算法對其關節電機控制系統進行pid參數整定，進行機器人關節的積分分離的pid控制策略和轉角誤差的理論分析，並進行了機器人三維力/力矩傳感器、接觸傳感器、測距傳感器和光電開關的標定與安裝。
  4. Equations of mesh, shorting contact line, undercutting limit line, meshing limit lines and the existence conditions, angle between the direction of relative speed and the direction of contact line, induced normal curvature about every point on the contact line are established. moreover, the paper also theoretically analyzed the error of the grinded gear surface. on the basis of the theory, the computer program is worked out to automatically produce the contact line and the boundary curves of mesh. analysis of meshing circs under different parameters can be done so that we can gain the best process condition

    首先對漸開面二次包絡理論進行了深入的探討，推導出了兩次嚙合的嚙合方程式、瞬時接觸線方程式、根切界限線方程式、嚙合界限線的方程式及其存在條件，相對運動速度方向與接觸線方向的夾角及接觸線上各點的誘導法曲率；此外，還對磨齒后工件的齒面誤差進行了理論分析；並在理論基礎上編制了相應的計算機程序，自動生成接觸線族及嚙合界限線，對不同參數條件下的嚙合情況進行分析，可以使工藝條件達到最佳狀態；最後研究了磨齒裝置，設計了磨齒機的傳動系統。
  5. The motion compensation of radar target and an analysis of influence of component imperfection in the realization of the method are presented. to evaluate the performance of the proposed method. monte carlo simulation has been conducted to estimate the root mean square error of the angle estimates and the spatial resolution snr threshold in the cases of both non - fluctuating targets and fluctuating targets

    在此基礎上，提出了針對相位權重角度超分辨法的雷達目標的運動補償方法，分析了雷達系統各部件的不理想性對超分辨性能的影響，用montecarlo方法對無抖動目標和有抖動目標在不同信噪比下的方位估計誤差和方位超分辨的信噪比門限進行了模擬計算，並將結果同波束空間music方法及cramerrao限進行了比較。
  6. Then, this paper presents an improved t measuring speed method basing on t measuring speed method, and simultaneously realizes speed and angle measuring with two quadrature encoder pulse circuits of tms320lf2407a. the measuring speed formula is amended based on measuring speed error analysis

    其次，在t法測速的基礎上提出了一種改進的t法測速法，並利用tms320lf2407a的兩組正交編碼電路同時實現速度與角度測量，在分析測速誤差的基礎上，對測速公式進行修正。
  7. In this paper the main work includes the analysis of the rotation of special angles, the range of rotation angles in cordic algorithm ; analysis on what condition should be fulfilled to reach any target angle ; analysis and simulation on error band and output spectrum ; imple - mentation of the architecture on fpga device

    我所做的只是很小一部分，主要包括對cordic演算法中特殊角的旋轉和旋轉角度范圍;在何種條件下可以達到任意角度的分析;對許多問題比如誤差上限和輸出頻譜的計算機模擬;這種結構在fpga器件上的實現。
  8. Based on the comprehensive analysis of the application status and the existed problems of transmission line fault location, this dissertation presented a new algorithm for fault location based on two - terminal asynchronous data, which can make correction for the integrate error of line parameter, length of transmission line, sampling value and so on. at the same time, it can work out the two - terminal asynchronous phase angle with the corrected parameters

    本論文在充分分析了國內外故障測距的理論與技術以及存在的問題后，針對輸電線路故障定位因線路參數變化對定位準確度的影響，提出了能夠對線路的參數、長度和采樣值等誤差等進行綜合誤差修正（ cie ）的新演算法，並利用修正後的參數來求解兩端的不同步相角差。
  9. Based on in - depth analysis on characteristic and function principles of psd, combined with characteristic of measured object, this article presents an new real - time measurement for symmetrical degree, guiding - groove, twining angle, inside radius of long direction pipe ; completes designing work for hardware of function module and application software ; and gives analysis and computation on error sources and uncertain - degree of measure result. based on above work, this article develops a parameter - auto - chosen, integrated and automatic measurement device for beeline degree, guiding - groove symmetrical degree, twining angle and inside radius of long direction pipe

    本文在深入分析研究psd的特點和工作原理的基礎上，結合被測量對象的特點，首次提出了長定向管導槽對稱度、纏角、內徑等實時自動化測量的一種新方法；完成了硬體功能模塊及應用軟體的設計工作；並對測量結果的誤差源及不確定度進行了分析和計算；在此基礎上研製了長定向管的直線度、導槽對稱度、纏角及內徑等參數自動、實時綜合測量設備。
  10. Four groups ’ measurement data are given based on built system, and the results and the error analysis of measurement range of 1. 5, angle step of 0. 06 is discussed in detail. a list table of fitting curve and angular displacement is given as well

    利用建立的測量系統給出了四組測量數據，詳細討論了測角范圍為1 . 5 、角度遞增0 . 06的測量結果與誤差，並給出標定擬合直線與角位移的查找表。
  11. Basing on carefulness analysis of error source, a new measuring system for small angle is designed in this paper. with super measuring precision it can be used to replace old measuring instrument

    為減小測量誤差，在對誤差源進行仔細分析的基礎上，本文研製了一種新型的高精度小角度測量儀器，以嘗試代替舊有的測量裝置。
  12. The allan variance ( av ) analysis method is used to evaluate the hrg signal. the result indicates that the main random error of hrg is angle random walk ( arw )

    論文採用allan方差法對半球諧振陀螺的信號進行隨機誤差分析，分析結果表明，半球諧振陀螺的角度隨機遊走誤差是陀螺隨機誤差的主要部分。
  13. The angle of attack and the sideslip angle are the two important measured quantities for the aircraft navigation / control aerodynamics analysis and structure analysis. for the different kinds of disturbance influence, now the sensors ca n ' t measure it accurately, in the high angle of attack, the error will add with the angle of attack increase

    迎角和側滑角是飛機飛行導航控制、航電等方面重要的兩個測量量，由於受到各種干擾因素的影響，現代傳感器很難對其精確測量，在超大迎角飛行過程中，其測量誤差隨迎角增加而增加。
  14. This paper studied zero - velocity correct technology for ins, based on analysis of ins error equation, it concluded the method by which we can use ins velocity output to estimate the attitude angle error when the vehicle halted, then it contrasted two schemes of conic approximation of attitude angle error and put forward a method to decide the approximation coefficient by time range

    本文首先研究了車載捷聯慣導系統（ ins ）的零速修正技術，在分析捷聯慣導系統誤差方程特點的基礎上，推導了停車時利用ins速度輸出估計姿態誤差角的方法，並對用二次曲線擬合姿態誤差角的兩種方案作了比較，提出了按時間分段確定擬合系數的方法。
分享友人
分享到 Line

分享到臉書