arc height 中文意思是什麼
arc height
解釋
弧高-
Armhole depth sleeve cap height and width as well as sleeve cap curve arc the important factors in defining modern sleeve shapes
摘要袖勢是由袖窿深、袖山高、袖肥及袖山曲線確定的。 -
One of the stars shall be bigger than the others, with its circumcircle s diameter being 310ths of the height of the flag, and shall be placed in the left ; the four other stars shall be smaller, with their circumcircle s diameter being 110th of the height of the flag, encircling the big star on its right in the shape of an arc
旗面為紅色，長方形，其長與高為三與二之比，旗面左上方綴黃色五角星五顆。一星較大，其外接圓直徑為旗高十分之三，居左；四星較小，其外接圓直徑為旗高十分之一，環拱于大星之右。 -
Methods ： fifty paired embalmed cadaveric humeri ( twenty - five pairs : fourteen from male donors and eleven from female donors ) were scanned in medial - lateral ( ml ) and anterior - posterior ( ap ) position according to the humeral retroversion by ct. images of the humeri in the transverse planes at the lowest border of neck ( lbn ), 20mm and 40mm distal of lbn ( lbn - 20 、 lbn - 40 ), isthmus, head - neck anterior - posterior ( hn - ap ) were obtained. sixty - one extracortical and intracortical parameters were measured exactly by image analytic computer software that included offset, head position, head - shaft angle, head to tuberosity height ( ht ), head thickness, curvature radius, articular surface arc ( sa ), neck diameter, isthmus position, proximal and distal border of isthmus, maximum coronal and sagittal diameter of medullary canal and thickness of cortical bone in four planes, including lbn, lbn - 20, lbn - 40 and isthmus
方法： 50根成對防腐肱骨（男14對，女11對）按肱骨頭扭轉角置於冠狀位和矢狀位，行肱骨全長，頭頸矢狀面，解剖頸下緣及其下20mm 、 40mm ，髓腔狹窄部四平面ct掃描，由ct軟體測量冠、矢狀位髓腔內外參數共61項，包括頭心?干軸距，頭位置，頭干角，頭?結節高度差，頭厚度，頭半徑，關節面張角，解剖頸直徑，髓腔狹窄部位置，解剖頸下緣及其下20mm 、 40mm和狹窄部四個平面髓腔的最大冠、矢狀徑，皮質骨厚度等。 -
Automatic control system of welding torch height in carbon dioxide arc welding with fine wire
細絲二氧化碳焊接焊炬高度自動控制系統的研究 -
The height of teeth points is different. when the balance of height is over 0. 1mm 0. 004 ", the sawing tangent will be the shape of arc. see the drawing
鋸尖端高度不一致，當高度差超過0 . 2mm 0 . 08 "時，鋸切線就會形成圓弧形，如圖。 -
At the same time, move the right hand toward the right side and form a hooked hand at a point slightly above shoulder height, while your left hand makes an arc past your abdomen and up to your right shoulder, with your left palm turned in. 2. turn your body to the left, facing 9 oclock, and take a step forward with your left foot, heel touching the floor first, to 8 oclock
右腳支撐身體重心，右手沿耳際上沿向前推出，經過左手掌心上向前推出，同時左腳向後撤步，重心后移，右腳以腳掌為軸，腳尖轉正，左手隨身體左轉，向後向下擺動，右手掌心翻轉，右腳向後撤步，左手沿左耳際上沿向前推出，右腳撤步，身體微向右轉，左腳以腳掌為軸，腳尖轉正。 -
3. turn your body to the right, shifting your weight onto your right foot. draw your left foot on its toes next to your right foot. make an arc up and round to the right with your right hand until your arm is at shoulder height
起勢：重心落於右腿，左腳腳跟輕輕提起，左腳向左平行開步，腳尖先地，重心移向兩腳之間，左腳落實，兩腳寬度同肩寬或略寬于肩。 -
Adaptive tracing system of height of welding gun in narrow gap welding based on arc sensing
基於電弧傳感方式的窄間隙焊槍高度自適應跟蹤系統
分享友人