as-cast alloy 中文意思是什麼

as-cast alloy 解釋
鑄造合金
  • as : adv （同…）一樣…；同樣〈在此是指 as… as… 結構中的第一個 as 它在主句中為指示副詞，第二個 as （在子...
  • cast : vt （cast; cast）1 投，扔，擲，拋。 ★此義動詞通常用 throw cast 只用於若干特殊句子。2 丟棄，拋棄；...
  • alloy : n 1 合金。2 （合金中的）劣等金屬。3 （金銀的）成色，成份。4 〈比喻〉攙雜品。vt 1 合鑄，熔合（金屬...
  1. Above all, alloy ductile cast iron is generally selected as the material of edger roll and its durability is better than high carbon semi - steel

    綜上所述，國外型鋼軋邊輥材質一般選用合金球墨鑄鐵軋輥，所以其耐磨性也相應地優于高碳半鋼。
  2. The product is produced according to general standard. as inoculant alloy in cast iron, deoxidizer in steel - smelting, the product is used widely in steel industry. it has unique and special function on a long time of anti - declining, reducing gasholes of cast material and improving processing function

    以硅為基礎的硅鍶合金按通用標準生產，作為高牌號灰鑄鐵的孕育劑，煉鋼中的脫氧劑，合金劑而廣泛應用於鋼鐵工業之中，作為孕育劑在抗衰退時間長，減白口能力強，減少鑄件氣孔，改善加工性能方面均有著獨特的作用。
  3. The strength and wear resistance of diamond drill bits for petroleum exploitation will be increased considerably when cast tungsten carbide is applied and adheres to the substrate firmly with cast tungsten carbide of 80 - 200mesh as the skelton and copper alloy as the soldering material in a process of non - pressure immersion

    石油鉆探行業用的金剛石鉆頭，用粒度為80 ? 200目的鑄造碳化鎢粉作骨架，採用無壓浸漬工藝，以銅合金作釬焊料，將鑄造碳化鎢與基體牢固結合，強度、耐磨性大大提高。
  4. The age hardening characteristic of as - cast cu20ni20mn and cu20ni35mn alloys and the interface characteristic between the alloy and cast tungsten carbide were studied, and on the basis of this study, composites of cu - ni - mn alloy reinforced with different volume fraction ( 0 - 45vol. % ) and different size ( 42 - 362 m ) of cast tungsten carbide particles were made by vacuum hot - pressing liquid sintering technology. pin on disk two body abrasion tests have been performed with different size of sic abrasive under different loads

    本文研究了鑄態cu20ni20mn和cu20ni35mn合金的時效硬化特性及其與鑄造碳化鎢的界面特性，並在此基礎上以不同尺寸（ 42 362 m ）的鑄造碳化鎢顆粒為增強體，採用真空熱壓液相燒結技術制備了不同顆粒含量（ 0 45vol . ）的鑄造碳化鎢顆粒增強cu - ni - mn合金基復合材料；以不同粒度的sic為磨料，在不同載荷條件下利用銷?盤磨損試驗機測試了復合材料的二體磨料磨損性能。
  5. 5. the comprehensive capacities of the azsm alloy were markedly promoted than that of the as - cast azsm alloy which was aged at 200 ?, air - cooled and furnace - cooled after solid - solution, aged at 90 ? and aged in nature after solid - solution

    5 ）鑄態azsm合金經200時效3小時、固溶4小時后空冷和爐冷、 400固溶-水淬90時效和自然時效的綜合性能較鑄態有顯著的提高。
  6. Failure of cast aluminiuin alloy box was analysed by metallographic and fractographic analysis, and cast defect anti variation of cross section thickness were identified as main causes of failure

    通過金相及電鏡斷口分析，確定箱體失效系鑄造缺陷和幾何截面差過大所致。
  7. The effect of the melting - current and melting - time on the microstructure of the as - cast sm - fe alloy is investigated and the phase composition of the as - cast sm - fe alloy with different sm content is analyzed. the parameters of the melting process and the proportion between different chemical elements are decided, which are based on the above - mentioned investigation and analysis

    實驗中研究了不同熔煉電流和熔煉時間對鑄態組織的影響，並對不同含量的sm - fe合金退火前後的相組成進行了分析，在此基礎上確定了熔煉參數和成分配比。
  8. The cast characteristics of investment casting for aluminum alloy is introduced. technology of investment casting for aluminum alloy in conventional plaster mold and ceramic mold and modification, refining technique of cast aluminum alloy as well as filtration purification of liquid aluminum alloy are studied

    介紹了鋁合金熔模鑄造的特點，鋁合金熔模鑄造常用的石膏型熔模鑄造和陶瓷型熔模鑄造工藝，鑄造鋁合金的精煉、變質、細化工藝和鋁合金液的過濾凈化技術。
  9. The phase composition and microstructure of sm - fe - zr alloy with different amount of zr are analyzed and the effect of zr content on the microstructure of as - cast sm - fe - zr alloy is studied. the results indicate that microstructure of as - cast sm - fe - zr alloy is improved obviously with 1. 0at % zr added, and that the long - time high temperature homogenization is unnecessary for the alloys with this microstructure. by this way, the purpose of the research to decrease the cost of preparation and optimize process is achieved

    分析了不同zr含量的sm - fe - zr合金的相組成和微結構，研究了zr含量對鑄態組織的影響，結果表明，添加1 . 0at的zr可以明顯改善合金的鑄態組織，從而可以避免昂長的高溫均勻化退火過程，取得了降低製造成本和優化工藝的效果。
  10. The composition, microstructure, properties and application of abrasion resistant materials such as mn steel, low alloy steel, white cast iron have been introduced in details and the wear resistant structure steel material and casting composite materials and high b casting alloy have also been reviewed

    摘要詳細介紹了耐磨材料奧氏體錳鋼、低合金鋼和白口鑄鐵的成分、組織、性能及其應用進展，還對耐磨鋼結材料和耐磨鑄造復合材料以及新開發的高硼鑄造耐磨合金進行了評述，期待為科學選擇耐磨材料提供參考。
  11. Effect of co on as - cast microstructure of al - 5 fe alloy

    合金鑄態組織的影響
  12. The ' peak time of alloy made by mlsd is 6 hours shorter than as - cast alloy, and the peak strength is up to 420mpa

    多層噴射沉積a卜s一cz mg合金的峰時效時間較鑄態合金提前約6小時，峰值強度為420mpa ， as 361
  13. The formation and distribution of quasicrystal in as - cast mg - zn - y alloy are investigated

    在此基礎上研究合金中準晶的形成機理和分佈特徵。
  14. It fits for cleaning or intensifying various cast iron pieces, cast steel pieces, forging pieces, welding pieces and heat treatment pieces with medium or small batches, as well as blasting and adding color for aluminum alloy pieces

    它適應于多品種中小批量的鑄鐵件鑄鋼件鍛件焊接件及熱處理件的表面清理或強化，亦可用於鋁合金件的拋丸增色。
分享友人
分享到 Line

分享到臉書