axial thickness 中文意思是什麼
axial thickness
解釋
軸厚度-
Using the system designed in this thesis work, flow field calibration of the wind tunnel is accomplished, which covers dynamic pressure drop coefficient, dynamic pressure time stability, axial static pressure gradient, boundary layer, and degree of turbulence, etc. boundary layer measuring principle and method are especially described in detail, the relationship between boundary layer thickness, wind speed setting, and the depth of the experimental section is summarized, and finally the calibration data for th e model center zone under specific wind speed are given
然後利用本文設計的系統完成了落差系數、動壓時間穩定姓、軸向靜壓梯度、邊界層及湍流度等內容的流場校測。特別對邊界層測量的原理及方法做了較詳盡的敘述，總結出邊界層厚度與設定風速、實驗段深度的關系，然後給出模型中心區一定風速下校正數值。 -
Here, fem is applied in the analyses of i ) fiber axial stress and interphase shear stress in fragmentation tests during initially applied strain, ii ) influence of temperature on the stress transfer across the interface, iii ) modulus and thickness of the interphase and their influence on interfacial stress transfer, iv ) interfacial debonding process, and v ) fragment aspect ratio, contact friction along the interface and their influences to the interfacial stress transfer efficiency
在論文的這部分工作中，使用有限元法描述和分析了逐節斷裂試驗中初始應變下的纖維軸向應力和界面相剪切應力，溫度對界面應力傳遞的影響，界面相模量和厚度、纖維節長寬比、界面脫粘過程、界面接觸中的摩擦效應等因素對逐節斷裂試驗中應力傳遞的影響。 -
Then an thorough computer modeling using finite element program with material, geometry and state triple - nonlinear taken into account is carried out on a series of influencing factors, such as comparison with npn - beam splice connection, comparison of varies designed theories, and the varying of fraction coefficient, diameter, grade, pretension and arrangement of bolts, thickness of web and flanges of beam and column, splicing location, axial loading on column, etc. lots of useful conclusions are drawn form computer modelling. finally, design and construction suggestions are given out. this study fills the black in the field of steel beam - to - column connection with cantilever beam high - strength bolted - splicing at both home and abroad
然後，本文在考慮材料、幾何和狀態三重非線性的基礎上，對該連接形式進行了全面的計算機模擬，主要考慮了帶懸臂梁段全螺栓拼接的樑柱連接節點與無拼接的樑柱連接及翼緣對接焊接腹板拼接的連接節點的對比，各種設計方法之間的對比，以及翼緣拼接和腹板拼接的螺栓間距、直徑和數量，拼接點與梁端之間的距離，梁和柱的翼緣、腹板厚度，柱的軸力，接觸面的摩擦系數，翼緣和腹板拼接板的厚度等因素的影響。 -
The flow equations are solved using finite difference technique. using body - fitted curvilinear coordinate system treated the boundary conditions. by iteratively solving the flow governing equation and the blade equation, the design of axial flow pump impeller in the quasi - three - dimensional rotational flow can be performed according to the angular momentum distribution, the blade which was designed in the lifting method, flow channel and the blade thickness given
其次在流動無粘性、不可壓及考慮葉片厚度的條件下，依據葉輪內的流動特性，推導了葉輪內三維流動周向平均流動控制方程以及葉片方程；在貼體坐標系中，採用有限差分法求解流動方程和葉片方程；在採用升力法設計出的葉片作為初始葉片、給定葉片速度矩分佈、葉片厚度分佈和葉輪軸面流道幾何形狀條件下，迭代求解流動控制方程及葉片方程，實現了軸流泵葉輪的準三維方法設計。 -
Measureing anterior chamber depth, lens thickness and axial length with orbscan tomography system
眼軸及前房深度中的應用 -
In chapter 5, using coordinate graphs, the influences of rectangular screw, trapezoidal screw and serrate screw on the generated axial thrust force, minimal mucus film thickness, load capacity of hydrodynamic pressure and circumferential friction are compared and analyzed
第五章，通過坐標圖對比分析了微型機器人在矩形螺紋、梯形螺紋、鋸齒形螺紋下，各螺紋參數對軸向摩擦牽引力、最小粘液膜厚度、粘液膜承載能力、周向摩擦阻力的影響。 -
In chapter 2, an accurate modified reynolds equation is derived. the modified reynolds equation is solved numerically with the finite different method, the generated axial thrust force, minimal mucus film thickness, load capacity of hydrodynamic pressure and circumferential friction under the rectangular screw are obtained. at last, using numeral methods and coordinate graphs, the influences of rectangular screw parameters on the generated axial thrust force, minimal mucus film thickness, load capacity of hydrodynamic pressure and circumferential friction are studied and analyzed
第二章，首先推導了非牛頓流體的變形雷諾方程，化簡了雷諾方程，得出了矩形螺紋下有限差分方程；還推出了矩形螺紋作用下軸向摩擦牽引力、粘液膜厚度、粘液膜承載能力、周向摩擦阻力無量綱表達式，最後用數值計算方法求解，通過坐標圖分析了矩形螺紋參數對軸向摩擦牽引力、最小粘液膜厚度、粘液膜承載能力、周向摩擦阻力的影響。 -
An analysis is developed for influence factors that have some influence on joints " behavior. the results show that axial ratio has a good and visible effect on the capacity of joints ; that the higher concrete strength is, the higher the capacity of joints is ; the ratio of reinforcements and the thickness steel web of column have large influence on the ductility src joints, not but the capacity of src joints
分析表明：軸壓比對節點的剛度、抗裂度的提高是有利的，且增大幅度較大；節點承載力和抗剪能力隨混凝土等級的提高而提高；鋼腹板厚度和配箍率的增大對節點承載力提高幅度不大，其對節點的延性影響較大。 -
The results showed that the influences of concrete strength on the soil and lining were not great, there was rational and economical thickness of the lining, and the age of concrete had large effect on axial force of lining
研究表明：混凝土強度提高對圍巖和襯砌結構影響不大；存在一個「合理經濟」的襯砌厚度；模擬計算中是否考慮混凝土齡期對襯砌軸力影響較大。 -
Taking advantage of hear forces current theory ? this paper deduces the formula of bending shear stresses, in which the influences of axial force, bending moment, variable section depth and the variable thickness of top slab, bottom slab and webs are taken into account
本文利用「剪力流理論」推導出了彎曲剪應力的公式，該公式不僅計及了軸力和彎矩對彎曲剪應力的影響，還計及了截面高度、頂板、底板及腹板厚度變化對彎曲剪應力的影響。 -
In static test, t - shaped and l - shaped specimens were respectively divided into four groups according to concrete strength grades, sectional height to thickness ratio, reinforcement ratio and ratio of axial compressive force to axial compressive ultimate capacity of section. how these factors affect the load - carrying and deformation of short - leg shear wall is known by analysis the result
在擬靜力試驗中對t形和l形短肢剪力墻分別進行了四組試驗，通過對試驗結果的分析，揭示了混凝土等級、截面配筋率、軸壓比和墻肢截面高厚比等因素對短肢剪力墻承載力和變形的影響。 -
Magnetic force pump magnet couplings " universal energy equation is educed by analyzing of demagnetization curve, ways of reverting force calculating are introduced according to the equation when inside magnet rotor have axial direction and radial displacement, circumferential moment of magnetic force has been given, magnetic force pump alnico ' s axial direction length, circumferential length, radial thickness amounts are summarized with the analyses of experiment results
利用退磁曲線法，推導磁力泵聯軸器能量通用公式，導出內磁轉子在軸向偏移和徑向偏置下產生的回復力計算方法，周向傳動轉矩計算方法，結合試驗結果，總結推薦磁力泵磁鋼軸向長度、周向長度、徑向厚度、磁極數設計方法。 -
In chapter 4, the modified reynolds equation is solved numerically with the finite different method, and the generated axial thrust force, minimal mucus film thickness, load capacity of hydrodynamic pressure and circumferential friction under the serrate screw are obtained. at last, using numeral methods and coordinate graphs, the influences of serrate screw parameters on the generated axial thrust force, minimal mucus film thickness, load capacity of hydrodynamic pressure and circumferential friction are studied and analyzed
第四章，首先求出鋸齒形螺紋下數值計算所需的有限差分方程，再推出了鋸齒形螺紋作用下軸向摩擦牽引力、粘液膜厚度、粘液膜承載能力、周向摩擦阻力無量綱表達式，最後用數值計算方法求解，通過坐標圖分析了鋸齒形螺紋參數對軸向摩擦牽引力、最小粘液膜厚度、粘液膜承載能力、周向摩擦阻力的影響。 -
( 3 ) the static load tests of 18 steel reinforced concrete columns with different ratios of length to thickness under axial compression were carried out, which provide reliable grounds for the design of this kind of members
3 、為填補空白，完成了18根不同長細比的型鋼混凝土軸心受壓柱靜力荷載試驗，為這類構件設計提供了可靠的試驗依據。 -
The axial frictional pulling force and the minimum thickness of mucus film were analyzed and calculated in detail when rectangular or trapezoidal cylindrical screw was being adopted in microcomputer
詳細分析計算了微型機器人在採用矩形和梯形圓柱螺旋時的軸向摩擦牽引力和最小粘液膜厚度。 -
On the basis of heat transfer theory, this paper analyzes heat transfer process in film boiling stage when axial workpiece is quenched vertically and distribution of steam film thickness as well as corresponding variation of heat - transfer coefficient
摘要以傳熱學理論為基礎，對軸類工件豎直淬火時膜沸騰階段的傳熱情況進行分析，分析了工件表面蒸汽膜厚度的分佈情況和傳熱系數的相應變化。 -
In this paper, the buckling behavior of cold - formed angle members is studied by non - linear finite element method. the influence of the width - thickness ratio of the single cold - formed angle column under axial load is analysed. the criteria of flexural buckling and torsional - flexural buckling for cold - formed egual - leg under axial loads is presented. according the calculating results of the ansys finite element method, the stability - coefficient formulas are simulated for the cold - formed loading single angle members of flexural buckling and torsional - flexural buckling
本文運用非線性有限元法對冷成型單角鋼的穩定性能進行了研究，分析了寬厚比對冷成型單角鋼軸壓桿穩定性能的影響，給出了等邊冷彎角鋼發生彎曲屈曲和彎扭屈曲的判斷條件，根據ansys有限元的計算結果擬合出了冷成型單角鋼軸壓桿在發生彎曲屈曲以及在發生彎扭屈曲時的穩定系數公式，在此基礎上得出了冷成型單角鋼軸壓桿在所有長細比情況下的穩定系數公式。 -
The results show that the improved structure has obviously reduced pressure drop and increased axial speed of the nozzle, as a result the wallop of electroplating solution is improved and the thickness of diffused layer reduced, the electrodeposition process improved, and what is more, the coating structure has been compacted, crystalline particles fined and the performance improved
結果表明，結構改進后，明顯減小了壓力損失，提高了噴嘴的抽向速度，電鍍液沖擊鍍件的沖擊力得到提高，有效地減少了擴散層的厚度，改善了電沉積過程，而且使鍍層組織緻密，晶粒細化性能得到提高。 -
Neglecting the influence of concrete stress - path, relative program is presented to make full - process analysis on compression - flexure members confined with cfrp in the compression zone, a key research is to analyze the effect of some parameters including axial compression ratio, thickness of cfrp, concrete strength on strength capacity and displacement ductility of reinforced compression - flexure members
在忽略混凝土應力路徑的影響下，編制相應程序對碳纖維布粘貼鋼筋混凝土壓彎構件進行了全過程分析及相關參數研究，並把計算結果與試驗結果進行了對比，兩者吻合較好。 -
Second, the thermoelastic coupling vibration of cylindrical shell are discussed by means of the same method. the coupling coefficient, amplitude of temperature, initial displacement, ratio of length to radius and that of radius to thickness are main factors which influence the thermoelastic vibration of cylindrical shell ; the higher the coupling coefficient is, the lower the axial force, the axial stress and the axial moment are
其次，我們用同樣的方法研究了圓柱殼的非線性熱彈耦合振動，主要結論如下：影響圓柱殼非線性熱彈耦合振動的因素主要有耦合系數、溫度幅值、長徑比、徑厚比以及初始位移參數；耦合系數越大，軸向應力、軸向力以及軸向彎矩越小。
分享友人