bar bending 中文意思是什麼

bar bending 解釋
彎鋼筋
  • bar : BAR ＝ Browning automatic rifle 白朗寧自動步槍。n 巴爾〈南斯拉夫港市〉。n 1 棒，桿，條；棒狀物。2...
  1. The beyond is the simple notation of serial number of pricker, totaled 7 digits of codes, in which the first digit represents the diameter of needle - bar of pricker, the second digit represents the siding of triangle side on functional section of pricker, the third digit represent the length of functional section of pricker, whereas in standard notation, it represents the distance from needlepoint to gradual deflating small port ( lower port ), the fourth digit represents the total length of pricker, which is the distance from the inside of bending helve to the needlepoint, the fifth digit represents the total quantity of dents on the cording of functional section, and the sixth digit represents the model of barb on functional section, while the seventh digit represents the distance between barbs on functional section

    以上為刺針編號的簡單寫法，共7位代碼，第一位是刺針針桿的直徑；第二位是刺針工作段三角面的邊寬；第三位是刺針工作段的長度，同標準寫法所不一樣的是針尖到漸縮錐小口（下口）的距離；第四位是刺針的總長度，按彎柄內側至針尖的距離；第五位是工作段棱上的總齒數；第六位是工作段上鉤刺的型號；第七位是工作段上鉤刺與鉤刺之間的距離。
  2. Thecalculating results show that the composite action between concrete floor and steel beamsgreatly influence the bending bearing capacity and initial rotational stiffness of joints, it shouldbe considered in practical engineer. reinforcement ratio of lengthways reinforcing bar andthe stiffener of web have great influencer on the behavior of connections, while the thicknessof end - plate and degree of shear connection have a litter influence on its behavior

    分析計算結果表明:樓板與鋼梁的組合作用對節點的抗彎承載力及初始轉動剛度的影響非常大，實際工程中節點設計應當考慮這種組合作用;樓板內縱向鋼筋配筋率與柱腹板加勁肋對節點性能影響顯著，而連接端板厚度及剪力連接程度的影響則不是太顯著。
  3. Aiming at technical features and technology requirements for cold bending forming production line of steel bar for packing case, equipment including in such line has been introduced with emphasis on working principle and devices for burr trimming and opening piercing, on control principle of hydraulic expanding and flying shearing on the line

    摘要針對包裝箱鋼條冷彎成形生產線的技術特點及產品工藝要求，介紹了包裝箱鋼條冷彎生產線的設備組成；重點闡述了包裝箱鋼條的在線預沖毛刺及豁口孔設備的工作原理及裝置、包裝箱鋼條產品的在線液壓擴孔及液壓飛剪技術的控制原理。
  4. Analysis of properties of bending bar under axial dynamic loads

    壓彎桿件的動荷性能分析
  5. Matals - rotating bar bending corrosion fatigue testing

    金屬旋轉彎曲腐蝕疲勞試驗方法
  6. The cancellation of web bending reinforcement and continuous bar in upper structure of continuous rigid frame bridge is discussed with mechanics method. 4

    並對連續剛構橋上部結構設計中取消腹板彎起索、下彎索和連續束問題進行了探討，從力學角度進行了分析研究。
  7. Metals - rotating bar bending corrosion fatigue testing

    金屬旋轉彎曲腐蝕疲勞試驗方法
  8. Calculate the dynamic stress intensity factor of simple edge crack round bar specimen in three point bending of nanling marble

    計算大理巖帶直切口三點彎曲棒梁試件的動應力強度因子的近似公式
  9. Reinforcing bar bending machines

    鋼筋彎曲機
  10. But this time, the authors considered more factors that can influence the precise, which include plastic resistant moment of special - shaped columns, bending stiffness of beams and cracking of walls. then, the equivalent width of diagonal strut is worked out. based on above results, the bar system model is used to calculating the internal force of the structure and the results were match the testing data basically

    給出結構的簡化計算方法，本文利用砌塊墻體的斜壓桿等效原理，並考慮了異形柱的塑性抵抗矩、 0梁的抗彎能力以及馬牙搓連接等多種因素，解出了斜壓桿的等效寬度，在此基礎上按桿系模型對結構進行了簡化靜力驗算，結果與試驗基本相符。
  11. Testing of metals ; rotating bar bending fatigue test

    金屬材料的檢驗.旋轉棒材彎曲疲勞試驗
  12. Metals - rotating bar bending fatigue testing

    金屬旋轉彎曲疲勞試驗方法
  13. To carry out computer program of bending bar, mathematical model of calculating support constraint forces is deduced from dynamic model of bending bar and superposition principle

    摘要根據承彎桿件的力學模型，利用疊加原理，推導出計算支座約束力的數學模型，它是實現承彎桿件計算機程序設計的前提。
  14. Then the area of ordinary steel bar may be calculated with the equation of ultimate bending capacity on normal sections and structures in detail. the method avoids the problems of the secondary internal force produced by the prestress and the troublesome " passive design ". the method makes design more simple, reasonable and economical, the new design mode of prestressed concrete structures in statically indeterminate structures is improved

    該方法以預應力混凝土結構中所有預應力混凝土構件同時滿足兩類極限狀態為設計原則，從整體上考慮了以結構中每一預應力混凝土構件滿足使用性能為要求聯立方程，確定預應力筋，再利用正截面承載力計算公式和構造要求確定非預應力筋。
  15. First, the paper sets up finite element models of 4 - point bending rc beam strengthened with frp sheet. not only material nonlinear of concrete and steel bar but bond style of longitudinal steel, stirrup and frp are taken into account

    本文首先建立了纖維布加固鋼筋混凝土梁四點彎曲的有限元模型，考慮了混凝土、鋼筋的材料非線性以及縱向鋼筋、箍筋和纖維布與混凝土之間的聯結關系。
分享友人
分享到 Line

分享到臉書