beam calibration 中文意思是什麼

beam calibration 解釋
電子束清晰度
  • beam : n 1 梁，棟梁，桁條；（船的）橫梁。2 船幅；（動物、人的）體幅。3 （秤）桿，杠桿，（織機的）卷軸，...
  • calibration : n. 1. 測定口徑。2. 刻度，標度，劃度數。3. 校準；標準化。
  1. Beam can be seen very easy to make high - precision calibration

    可見光束使高精度校準十分簡單易行
  2. The dcb ( double cantilever beam ) met hod to test the interlaminar toughness of fabric - reinforced laminates and the modified compliance calibration method ( mcc ) were adopted in this research. the double cantilever beam ( dcb ) test was executed for stitched laminates to evaluate the interlaminar fracture toughness. the stitch parameters ( stitch line spacing and pitch spacing ) were changed and their effects on interlaminar fracture toughness were examined by means of dcb test by using improved insert type loading fixture

    試驗中採用改進的插入型夾具、雙懸臂梁dcb （ doublecantileverbeam ）試驗方法，測試了載荷?試樣開口位移曲線，依據改進的柔度梁方法（ modifiedcompliancecalibrationmethod （ mcc ） ）計算出了各個試樣的層間斷裂韌性（ r曲線）及層間斷裂韌性的平均值，闡明了縫合工藝參數與層間斷裂韌性（ g _ （ ic ） ）間的關系，以拉伸與彎曲強度為約束條件，以層間斷裂韌性值為目標優化了縫合工藝。
  3. Experimental results on butane and butane - plant oil flames indicated that, measurement precision by the multi - wavelength method is strengthened by taking radiation information on multiple wavelength units into consideration, and moreover, the radiation calibration procedure is simplified, in that a halogen light source is used instead of in situ flame radiation. in section 2, fluctuation and averaging analyses are carried out on optical transmission signals by particles passed through laser beams to derive particle size and concentration in measuring area, furthermore, correlation calculations are conducted on two adjacent laser beam signals to obtain flowing velocity of particle

    對丁烷氣體火焰及丁烷-植物油混合燃料火焰的測量結果表明，多波長分析方法優于傳統的雙色法，表現在兩個方面：一、由於綜合考慮多個波長單元上的火焰輻射信息，多波長方法的測量精度比雙色法有較大的提高；二、在多波長分析方法中，採用標準鹵素燈進行相對輻射強度標定，簡化了雙色法中的火焰絕對輻射強度的標定。
  4. Acceptance tests for co2 - laser beam machines for welding and cutting - part 3 : calibration of instruments for measurement of gas flow and pressure

    Co2激光束焊接機和切割機的驗收試驗.第3部分:氣體流量和壓力測量儀的校準
  5. Acceptance tests for co2 - laser beam machines for high quality welding and cutting - calibration of instruments for measurement of gas flow and pressure

    高質量焊接和切割用co2激光束機的驗收試驗.氣體流量和壓力測量儀的校正
  6. For a precision torque tester, the test device will be calibrated against the torque generated by weights hanging at the end of a beam. calibration is made by applying torque of known values to the test device in sufficient number of steps ( normally about 7 ) distributed throughout its usable range, from lower test values to full scale capacity

    由吊在杠桿尾端的砝碼而產生的扭力，將會用作校正精密扭力檢測儀。校正過程是對測試儀器加以已知的扭力。加以的扭力，在儀器的應用范圍內，逐級（通常為七級）由最低測試數值加至其最高扭量。
  7. Standard practice for use of calorimetric dosimetry systems for electron beam dose measurements and routine dosimeter calibration

    電子束劑量測定和常規劑量儀校準用量熱劑量測定系統使用的標準實施規程
分享友人
分享到 Line

分享到臉書