beam calculation 中文意思是什麼

beam calculation 解釋
梁計算
  • beam : n 1 梁，棟梁，桁條；（船的）橫梁。2 船幅；（動物、人的）體幅。3 （秤）桿，杠桿，（織機的）卷軸，...
  • calculation : n. 1. 計算，計演算法。2. 推定，預測。3. 深思熟慮，精打細算；慎重的計劃；算計。
  1. The thesis has summarized the development of the oblique - pull bridge, its construction technology and the importance of bridge construction control, then has introduced project general situation, and has narrated detailed regulation, organization construction, the major work and difficult part of this bridge construction control. the following is the key part of this thesis, firstly, it has introduced the experiment work of early stage, structural calculation and its theoretical result : the absolute altitude of each operating mode, the absolute altitude of building mould in each section and the absolute altitude after pouring concrete ; then, it has discussed the method and content of the line shape control of the main beam, actual absolute altitude of building mould is put forward, and it has described the method of structural stress monitoring, how to arrange measure point and collect data, and how to analyze data. it has also narrated the method of rope force detection and structural temperature inspection

    本論文在總結了斜拉橋的發展及其施工工藝，並指出了橋梁施工控制的重要性之後，簡要的介紹了工程概況，敘述了炳草崗金沙江大橋監控細則、組織機構及監控的主要工作和難點部分；論文的核心部分，在介紹了炳草崗金沙江大橋施工控制與監測工作的前期實驗工作和施工各工況標高、各節段支模標高、澆注混凝土后的標高的結構計算和其理論計算結果之後，詳細論述了主梁的標高線形控制方法和內容，實際支模標高的提出，結構應力監控的方法、布點、測讀及其對測讀數據的合理分析方法，索力檢測和結構溫度監測的方法。
  2. Application and calculation of wall beam in the brick room of ground floor frame

    墻梁在底層框架磚房中的應用及計算
  3. Being lacking of understanding of behaviors of circular working shaft, the paper proposed theory about ring - beam ' s load - distribution calculations and analyzed the structural behavior of circular working shaft ( cws ) by the numbers from the standpoint of properties of structural style and stress incorporated with thoughts of shared load introduced to research of cws. first, regarding cws as structure of series of hypothetic horizontal circular rings and vertical beams, and considering cws ' s formation and development, the paper proposed load - distribution thoughts to solve cws ' s calculations. ring - beam calculation theory was put up and software cbtlmp1. 0 was worked out based on the conditions of external applied load shared by rings and beams, and of deformation conformity

    首先，本文提出用分載思想解決圓形工作井結構的計算分析問題，將圓形工作井結構看成是由一系列的假想的水平圓環和豎直梁組成的結構，考慮工作井形成過程及形成階段與項進階段的連續性，根據某一時刻相對于上一時刻外載增量由環與梁分擔、環與梁在交叉處變位增量一致的條件將環計算理論與梁計算理論結合起來，據此建立了環?梁分載計算理論並研製了環?梁分載計算分析軟體cbtlmpv1 . 0 。
  4. Aberration of electronic lens made by electron gun and aberration of magnetic deflection system made by dy are comprehensively investigated, so is the shadow mask ' s effect on electron beam landing screen error. the conclusion can be get that, because the distribution of electron beam landing screen ( distribution of luminance ) is affected by many kinds of factors, it cannot get the correct function by calculation, and should be get by measurement instead

    全面分析了cpt電子槍發射系統形成的電子透鏡像差與磁偏轉系統形成的偏轉像差；分析了蔭罩的自身厚度與位移對電子束著屏的影響，並由此得出結論，著屏電子束分佈（即亮度分佈）受著許多因素的影響，理論分析是半定量的，著屏電子束分佈需要用精確的測量儀器來測量。
  5. Do some necessary calculations and decide on the general scheme of compton back - scattering imaging scanner to the real wall inspection. include the selection of radioactive source, the calculation of compton back - scattering beam, the calculation of the basic condition of finding out the different materials and the determination of some important parameters as well. 3

    其主要內容包括入射源的選擇，散射粒子的理論計算，發現異物的最低條件計算以及系統的一些重要參數的確定，主要包括：放射源的選擇，散射角的確定，后準直器的形狀與尺寸，前準直器的尺寸，前準直孔的大小，檢測器的種類與型號，檢測器的效率等。
  6. Consequently, on the basis of non - winkler foundation model, a finite - element method that utilizes foundation flexibility matrix into iterative calculation is proposed in this paper originated from the item " the optimal design theory and research of pile capping beam " sponsored by natural science fund of hunan province, which the continuity of soil mass can be accounted for under various boundary conditions, different loadings and irregular beam characters

    本文結合湖南省自然科學基金項目「樁基承臺梁優化設計理論與方法研究」 ，針對非文克爾地基（半空間、線性變形層或單向壓縮層地基模型等）上的樁基承臺梁，提出一種利用地基柔度矩陣來進行迭代的有限單元法，可充分考慮梁下土體的連續性，並對基礎與土體脫開、承臺梁截面變化、梁體邊界條件復雜、上部荷載類型變化以及梁下基樁承載力差異等情況進行分析計算。
  7. During calculation of the ultimate flexural capacity of composite beams, it assumes steel beam, concrete board and connecter are plastic, calculates them by ultimate equilibrium method

    在組合梁受彎極限承載力計算中，認為鋼梁、混凝土板和連接件完全塑性，採用極限平衡法計算。
  8. Besides the scalar diffraction theory, the simulation method of beam propagation method, which is extensively used in the simulation of integrated optical devices, is also discussed though no successful result of calculation with bpm is given

    本文給出了平場輸入和輸出edg的設計方法，並利用標量衍射理論對設計的結果進行模擬，驗證了平場輸出edg具有很好的分波效果。
  9. Elastoplastic analysis and practical calculation of steel beam columns under fire condition

    火災下鋼構件的彈塑性分析和實用計算
  10. Secondly, by making use of the features of lattice frame anchor structure which can protect slope and retain stability of landslide together with its small space between beams and light anchor, the calculation model and formulas of slope force are dealt with and the design process of lattice beam and pillar as well as anchor and plate are introduced carefully

    利用格構式錨桿框架結構所採用的小間距、小噸位錨桿及連續格構樑柱，從而使格構樑柱受力較均勻，適合鬆散堆積體滑坡治理的需要，即同時滿足深層抗滑和淺層護坡。
  11. The ansys, a kind of fea program, was used to build model of small carriage. the procedure of gantry beam bump with secondary beam of bridge was reappeared by running nonlinear calculation and loading program which was written by apdl program language. the closest deforming result was gotten, and the deforming of main beam, secondary beam and end beam and inner stress distribution status were calculated

    採用大型三維有限元軟體ansys對該起重機以及小車架等進行了建模、應用apdl語言編寫加載程序、進行非線性計算，再現龍門橫梁與起重機副梁碰撞過程，最後得到與實際變形結果最接近的一種狀態，得出起重機橋架主梁、副梁、端梁的變形以及其內部的應力分佈情況。
  12. In the hogging condition, double bottom and the side shell remain the ultimate bucking strength, deck and upperwing tank remain the yield stress, and the other parts keep elasticity. then the key to calculate the ultimate strength of ship hull girders is to ascertain the ultimate bucking strength of the stiffened panels. in this regard, the developed formulation is designed to be more sophisticated than previous simplified theoretical method for calculating the ultimate strength of stiffened panels under combined in - plane bending and lateral pressure. fabricatio n - related initial imperfections ( initial deflections and residual stresses ) are included in the panel ultimate strength calculation as parameters of influence. all possible collapse modes involed in collapse of stiffened panels, including overall buckling collapse, column or beam - column type collapse, tripping of stiffeners and local bukling of stiffened web are considered

    確定了船體梁整體破壞時的剖面應力分佈之後，關鍵在於確定板架的極限屈曲強度。本文充分考慮了在縱向彎曲、橫向壓力作用下加筋板可能發生的幾種破壞模式，即板架的整體屈曲破壞、樑柱形式的破壞、筋的側傾、腹板的屈曲並同時考慮了初始焊接殘余應力、初撓度的影響，使其更精確的計算加筋板的屈曲強度。對于加筋板中加強筋腹板的局部屈曲，採用解析法推導出筋的腹板的撓度方程及其邊界條件，求解相應的方程，從而計算出腹板的局部屈曲應力。
  13. Simulation calculation for the energy deposition profile and the transmission fraction of intense pulsed electron beam at various incident angles

    不同入射角度下強流脈沖電子束能量沉積剖面和束流傳輸系數模擬計算
  14. In common design, the calculation of suspender inner force uses the model of beam with simply supported ends, because of all kinds of restraint

    由於各種條件的限制，在通常的設計計算中，利用橋面簡支梁模型計算吊索（桿）內力。
  15. Calculation of protection dose at the labyrinthine outlet of electron beam irradiation apparatus

    電子束輻照裝置迷路出口處的防護劑量計算
  16. In chapter 5, by number value simulation calculation and experiment of one simple support beam, we will compare the magnitude of the coupling static and dynamic stress at each point on the girder under harmonic excitation, and so find conclusions such as : ( 1 ) there are so much correlations between structure damage and environmental effect and exterior excitation leads dominant effects in structure damage that we should consider static and dynamic stress together. ( 2 ) new intension design rules should be set up, according which the range of structure possible damage position should be estimated in advance

    得到以下結論： （ 1 ）結構的破壞和環境的影響密不可分，外部激勵在結構破壞中發揮了重要的作用，應該將結構所受的靜力和動力一起考慮； （ 2 ）應該建立新的強度設計準則，並以此作為依據，對已知結構的可能損傷位置有預先的范圍估計，從而為損傷識別的準確定位提供理論依據。
  17. The calculation result shows that the model can keep the balance of the link level budget margin among the different spot - beam cellars, the onboard power in satellite can be used more effectively and the model is possessed of better applied value

    計算結果表明，該點波束模型能使各點波束小區的鏈路電平預算余量達到平衡，並使星上功率得到更有效的利用，彌補了現有模型的不足，具有較高的應用價值。
  18. After measured the laser energy distribution of kunming slr station, the parameters of this non - gassian and non - spherical symmetric laser beam were deduced according to correlation definition. applying its laws and deduced laser beam parameters, the change of laser beam dirvergence angle was studied in detail when adjusts transmission system focus. moreover, calculation based on these measured data indicates that the laser shaded by the second mirror of telescope is amazingly up to 39. 8 %, an optical element was designed for the settlement and it worked satisfactorily when put it into practice

    之後測量了雲南天文臺激光的橫向能量分佈，根據相關定義確定了這束非高斯非球面激光的參數，應用它的傳輸變換規律和測量參數研究了調焦中激光發散角的變化，並根據測量數據計算出激光發射時副鏡擋光比例達到驚人的39 . 8 ，研製出光劈解決這一問題，取得了很好的效果。
  19. Generally, the skew bridge ' s calculation theories can be divided into three types : the category 1 is the plank theories method, such as the finite difference method, the finite element method and the finite strip method, etc ; the category 2 is the beam theories, such as the grid beam theories, the general grid theories, the rigid cross - beam method, the elastically - supported continuous beam method and the bar system analytical method, etc ; the category 3 is the practical method, such as the g - m revising method, the grid - beam simple method and ghali form coefficient method, etc

    目前關于斜梁橋的計算理論和方法概括起來，大致可以分為三類：第一類為板理論方法，如有限差分法、變分法、有限單元法、有限條法等；第二類為梁理論法，如格構梁理論、一般格構理論、剛性橫梁法、彈性支承連續法、桿件結構的分析方法；第三類為實用計演算法，荷載橫向分佈的計算方法如g ? m修正法、格構梁的簡易法、 ghali表格系數法等。
  20. The design realm in the province of jilin, use more software is the bridge doctor system, bridge master, system of asbest, procedure of qjx and province highway of jilins survey to design the hospital to by oneself develop of the t beam plank beam painting procedure, the cover beam calculation painting procedure, a pillar calculation procedure, the upper part procedure compute a procedure mostly, even some procedures can paint, but the province painting of basic and dissatisfied foot jilin of born diagram paper style, the diagram paper the modification quantity compare greatly, the procedure that the lower part procedure adopts to by oneself

    在吉林省內設計領域，使用較多的軟體是橋梁博士系統、橋梁大師、 asbest系統、 qjx程序及吉林省公路勘測設計院自行研發的t梁板梁繪圖程序，蓋梁計算繪圖程序，樁柱計算程序，上部程序多是計算型程序，即使有些程序能夠繪圖，但生成圖紙基本不滿足吉林省繪圖風格，圖紙修改量較大，下部程序多採用自行編制的程序，但大多數程序是dos系統的程序，使用不方便，同時與現行規范多有不符。
分享友人
分享到 Line

分享到臉書