bias tube 中文意思是什麼
bias tube
解釋
偏壓管-
The g2 adjustment is a service or factory level adjustment, normally only done at the factory or at installation, which adjusts the bias current for each tube individually so that they all come on at the same time
每一隻投影管都需要一定量的偏置電流才能夠正常工作，然而，每隻管及其相應的電路參數都會有些差異，因此所需的偏置電流也不太一樣。 -
The thesis has done the widespread investigation and study to the domestic and foreign ’ s technologies of analogy low voltage and low power, and analyzes the principles of work, merts and shortcomings of these technologies, based on the absorption of these technologies, it designs a 1. 5v low power rail - to - rail cmos operational amplifier. when designing input stage, in order to enable the input common mode voltage range to achieve rail - to - rail, it does not use the traditional differential input pair, but use the nmos tube and the pmos tube parallel supplementary differential input pair to the structure, and uses the proportional current mirror technology to realize the constant transconductance of input stage. in the middle gain stage design, the current mirror load does not use the traditional standard cascode structure, but uses the low voltage, wide - swing casecode structure which is suitable to work in low voltage. when designing output stage, in order to enhance the efficiency, it uses the push - pull common source stage amplifier as the output stage, the output voltage swing basically reached rail - to - rail. the thesis changes the design of the traditional normal source based on the operational amplifier, uses the differential amplifier with current mirror load to design a normal current source. the normal current source provides the stable bias current and the bias voltage to the operational amplifier, so the stability of operational amplifier is guaranteed. the thesis uses the miller compensate technology with a adjusting zero resistance to compensate the operational amplifier
本論文對國內外的模擬低電壓低功耗技術做了廣泛的調查研究，分析了這些技術的工作原理和優缺點，在吸收這些技術成果基礎上設計了一個1 . 5v低功耗軌至軌cmos運算放大器。在設計輸入級時，為了使輸入共模電壓范圍達到軌至軌，不是採用傳統的差動輸入結構，而是採用了nmos管和pmos管並聯的互補差動輸入對結構，並採用成比例的電流鏡技術實現了輸入級跨導的恆定;在中間增益級設計中，電流鏡負載並不是採用傳統的標準共源共柵結構，而是採用了適合在低壓工作的低壓寬擺幅共源共柵結構;在輸出級設計時，為了提高效率，採用了推挽共源級放大器作為輸出級，輸出電壓擺幅基本上達到了軌至軌;本論文改變傳統基準源基於運放的設計，採用了帶電流鏡負載的差分放大器設計了一個基準電流源，給運放提供穩定的偏置電流和偏置電壓，保證了運放的穩定性;並採用了帶調零電阻的密勒補償技術對運放進行頻率補償。 -
This machine adopts japanese pro - face touch screen and mitsubishi plc control technology. in addition, it is set with automatic gear - shifting vacuum gauge, a three - flow controller, side - installed heating tube, computer pid automatic temperature control, and two sets of flat magnetic controlled target, contra - variant magnetic - controlled power source, and contra - variant bias power with easy operation and top grade film layer. they are widely used in decorative film layer, and compound film layer in plating
該設備採用日本pro - face觸摸屏和三菱plc集中控制裝有電腦自動換檔真空計，三路流量控制器，邊裝式加熱管，電腦pid自動控溫，配備兩套邊裝式平面磁控靶，逆變式磁控電源和逆變式偏壓電源，操作簡單，膜層細膩，廣泛適用於鍍制各種裝飾膜層和復合膜層。 -
This machine adopts japanese pro - face touch screen and mitsubishi plc control technology. in addition, it is set with automatic gear - shifting vacuum gauge, a two - flow controller, side - installed heating tube, computer pid automatic temperature control, and 32 sets contra - variant arc power supply and contra - variant bias power. they are widely used in plating different thick film layers of mono - metal and many compound film layers
該設備採用日本pro - face觸摸屏和三菱plc集中控制裝有電腦自動換檔真空計，兩路流量控制器，邊裝式加熱管，電腦pid自動控溫，配備32隻逆變式弧電源和逆變偏壓，適用於鍍制各種特種單金屬厚膜層或多鐘金屬復合膜層。
分享友人