bolt point 中文意思是什麼

bolt point 解釋
螺栓尖
  • bolt : n 1 螺釘，螺栓。2 （門窗等的）插銷；閂，鎖簧。3 箭，矢；弩箭；【軍事】槍機，槍栓。4 電光，閃電。5...
  • point : n 1 尖頭，尖端；尖頭器具；〈美國〉筆尖；接種針，雕刻針，編織針；小岬，小地角；【拳擊】下巴。2 【...
  1. After the valve has been adjusted to its balance set point and without moving the handwheel, remove the retaining bolt from the end of the handwheel using a 1 / 4 " allen wrench

    在閥門調整到平衡點，並且沒有旋轉手輪后，採用一把1 / 4 "通用扳手從手輪末端拆卸固定螺栓。
  2. With the handwheel / turn indicator sleeve assembly still at its balance set point indication, reinstall them on the valve stem and hold in place with the 1 / 4 " retaining bolt

    這時手輪/旋轉指示器套筒總成仍然位於平衡設置指示點上，將它們重新安裝到閥桿上，並用1 / 4英寸固定螺栓固定在其位置上。
  3. The experiment procedure and analysis result about exteriorly extended end - plate connection with high strength bolt are introduced primarily ; each sample ' s dimension is given. the adding load equipment, measuring apparatus placed, measuring point established is detailed. adding load measure load and m - curve is produced ; the single span gabled frames horizontal displacement formula is deduced when the horizontal concentrated force is applied to it

    重點介紹了外伸端板高強螺栓連接的實驗過程及實驗分析結果，介紹了各組試件的形狀尺寸、加載裝置、測量儀器安放、測點的布置等；給出加載方式及測出的m -曲線；計算出試驗節點的初始剛度；推導水平集中力作用下單跨門式剛架考慮節點半剛性的側移計算公式。
  4. Jdy - 002 full frameless glass door electric bolt delayed time : 0s, 3s, 6s, 9s monitor output point no nc, automatically cut off the detection point after 14s when locked working voltage : 12vdc start current : 0. 85a, working current : 0. 25a features : voltage range : 9 15v with led, no noise bright silver cover left - opened type and right - opened type can be widen more than12mm dimension : 205 x 55 x 40mm weight : 1260g right - opened type left - opened type yiwu qimingxing computer company copy right

    Jdy - 002全無框玻璃門電插鎖此款為右開門此款為左開門可調試延時啟動時間： 0 3 6 9秒監視接點輸出no nc信號，門上鎖后14秒自動切斷感應點使用電壓12vdc ，啟動電流0 . 85a ，持續工作電流0 . 25a特點：具指示燈，無噪音適應電壓寬度9 - 15vdc可夾玻璃門寬度為12mm亮銀色面板，分為左右兩款外形尺寸： 205 x 55 x 40mm重量： 1260g
  5. Bolt, pan head, amagnetic with cone point nf l 22 - 072 cross recess

    有nf l22 - 072十字槽錐頂磁性皿形頭螺栓
  6. Connecting point for earthing and short - circuiting devices ; cylinder bolt and annuar slot for earth - side connection

    接地的接點和短路設備.連接接地一邊帶環型槽圓柱形螺
  7. After the valve has been set to the correct balance point, record the setting. without turning the handwheel, remove the retaining bolt from the end of the handwheel

    在正確設置閥門的平衡點后，記錄下設置值。不需要旋轉手輪，直接從手輪末端拆卸固定螺栓。
  8. At the last of this paper, we summarized the deficiencies of simulating pre - stressing anchor and proposed the new and accurate simulating method which is given up the traditional tow points applied forces and applied a point reverse forces, made beam element simulate the anchor bolt, made interface element simulate concrete. in addition, we proposed two simulating methods applied on flock anchors which improved on considering the contribution of anchors " tangent - orientation stiff. one is post - stressing offset method ; the other is anchor element method

    另外，本文還提出了兩種改進原有群錨模擬中沒有考慮錨索限制變形的側向剛度貢獻的方法，即后續張拉補償法和錨索單元法，通過平面直線型滑動破壞中這兩種方法與傳統群錨的兩點集中力法的比較、分析，表明這兩種方法的結果與實際情況較為相符。
  9. An approach is brought forward to consider arbitrary orientation rock bolt, in this model while forming the calculation mesh, the orientation of the anchor need n ' t consider, only the coordinate formation of starting point and destination of the rock bolt is needed, the formation of rock bolt in combination element can be formed automatically

    闡述了任意巖體錨桿的計算模型，該模型在形成計算網格時可不必考慮錨桿的方位，只需賦予錨桿的起點與終點的坐標信息，即可自動形成錨桿在組合單元中的信息。
分享友人
分享到 Line

分享到臉書