bonding strength 中文意思是什麼

bonding strength 解釋
鍵強度
  • bonding : 冰凍膠結
  • strength : n. 1. 力，力量，體力。2. 強度，濃度；長處；（要塞等的）抵抗力。3. 實力；兵力；全體人數，額定人數，編制。4. 筆力；文勢。5. （證券等的）市價堅挺。6. 〈美俚〉（可能有的）利潤。
  1. Differential thermal analysis ( dsc ) indicates that acid - anhydride reacts with amidogen in nylon 11 to form chemical bond and boost up bonding strength of interface

    Dsc分析表明，接枝物中的酸酐基團與尼龍11中的氨基發生反應，形成化學鍵，使得界面粘接力增強，從而使沖擊強度得到提高。
  2. Effect of heat treatment on induced apatite deposition and bonding strength of the alkali treated titanium oxide layer for carbon carbon composite

    碳復合材料上堿液處理氧化鈦鍍層誘導沉積磷灰石和結合強度的影響
  3. The particles distributed hi the matrix of grey cast iron, but some contact each other. the composite layer extend gradually into the substrate. when volume fraction of wc is 36 wt % and 27 wt %, the matrix of the composite is high chromium cast iron, consist of white carbide bars and the austenite. wc particles distributed uniformly, retaining approximately quondam granular form in the composite layer which has an evident interface area with the substrate, with good bonding strength

    對不同碳化鎢體積分數的灰鐵和低鉻鑄鐵基復合材料的微觀組織結構分析表明：碳化鎢體積分數為52時，復合層內基體為灰口鑄鐵組織，顆粒直接分佈在灰鐵基體上，部分碳化鎢顆粒有相互接觸的現象，基材與復合層之間沒有明顯的過渡；碳化鎢體積分數為36 、 27時，復合層內基體為高鉻鑄鐵，由面塊狀的奧氏體和白條狀碳化物組成，碳化鎢顆粒表面固溶於基體組織中，粒形基本保持完整，分佈均勻，與基體構成冶金結合，基材與復合層之間存在一個明顯的平緩過渡區。
  4. A study on bonding strength of hybrid integrated circuits

    功率混合集成電路鍵合強度控制研究
  5. Liquid and solid bonding strength of cu fe interface in copper clad steel

    鋼液固相復合界面的結合強度
  6. Standard test method for cold bonding strength of refractory mortar

    耐火灰漿的冷粘接強度的標準試驗方法
  7. In the thesis, we developed new alloy and cermet coating materials by adjusting the content of cr in ni and add some amount of si and cr _ ( 3 ) c _ ( 2 ). the test of high temperature oxidation and corrosion, erosion, bonding strength, hardness, thermal cycling and thermal shock of coatings tests were carried out in this study

    我們通過調整nicr合金中cr的含量，以及在nicr合金中加入適量固溶強化元素si形成新型nicr基合金塗層材料，以及加入cr _ 3c _ 2陶瓷形成nicr基金屬復合陶瓷塗層材料。
  8. Fgm has many superior properties such as eliminating interface crack between the two materials, reducing the thermal and residual stress, thermal barrier, thermal shock resistance, anti - corrosion, increasing the bonding strength and toughness, high - temperature strength ( to 2000 c ) etc., as compared with traditional composite materials

    它較目前廣泛使用的隔熱性耐熱復合材料有許多優點，如可以消除材料間的界面，緩和熱應力，具有較高的機械強度，抗熱沖擊性和耐高溫性（達2000 ）等。
  9. Inorganically post - installed bars although have the ideal durability and heat - resistance, its bonding strength is low. it is unable effectively to transmit the load, the anchor depth is too big. these restricted application of the inorganic anchoring material in the post - installed fastening project

    無機植筋雖有較理想的耐久性能和耐高溫性，但其粘結強度較低，無法有效傳遞荷載應力，錨固深度太大，這制約了無機粘結材料在植筋工程中的應用。
  10. Interfacial bonding strength of sprayed plastic coating based on co2 laser thermal effect

    2激光熱效應的噴塑塗層界面結合強度研究
  11. A review on measurement methods for interfacial bonding strength between coating and substrate

    基體材料界面結合強度測量方法的現狀與展望
  12. The results show that, the interfacial bonding strength of new and old concrete is evidence lower than the new or old concrete itself. besides the dimension and roughness of bond interface, the chemical reaction degree at the interface is also the main factor

    分析結果表明：新老混凝土的界面粘結強度除了受老混凝土界面的尺寸及表面結構、粗糙程度影響外，還與新老混凝土粘結界面間發生化學反應的強弱有關。
  13. In this paper, the rapid repairing method using cement concrete lamina is presented, two key designing parameters are analyzed : the interfacial bonding strength of new and used concrete and the shearing stress in interface

    本文闡述了水泥混凝土路面快速薄層修補的方法，研究了修補中兩個重要設計參數：新老混凝土界面抗剪粘結強度和新老混凝土粘結面剪應力，並進行了新老混凝土界面抗剪粘結強度試驗和混凝土收縮試驗。
  14. The melted tungsten carbide would react with the steel matrix on the interface and the reaction zone was observed as a result. the reacting production was examined as fe3w3c by means of x - ray diffraction and scanning electron microscopy analysis. the reaction between tungsten particle and steel matrix could improve the interfacial bonding strength remarkably

    Wc鋼復合材料的制備過程中， wc顆粒在高溫下發生了局部溶解並在wc顆粒和鋼基體界面處發生了界面反應； x射線衍射和電子衍射花樣分析表明，反應產物為高穩定性的fe _ 3w _ 3c ，界面反應有效地改善了wc顆粒與鋼基體的界面結合。
  15. Through the experiment of the interfacial bonding shear strength and the shrinkage strain of concrete, the influence of the interfacial roughness of used concrete surface and interfacial bonding agent to interfacial bonding strength is revealed ; new concrete component and the shape and size of concrete slab are main factor affecting the shearing stress in layers

    試驗結果表明：老混凝土粘結面的粗糙度和界面粘結劑類型對新老混凝土界面粘結強度影響很大；新鋪混凝土材料和混凝土路面板形狀尺寸是影響新老混凝土粘結面收縮剪應力的主要因素。
  16. Interface bonding strength of clad transition joints welded in two different welding procedures is compared and a proper welding procedure is determined

    對兩組不同焊接規范下復合過渡接頭的界面結合強度進行了對比，確定了合適的焊接工藝參數。
  17. In practical projects, because of high bonding strength of the organic anchoring material, organically post - installed bar was widely applied. however, the durability and the heat - resistance of the organic anchoring material are relatively bad, the structure lied in hidden danger

    在實際工程中，因為有機粘結材料的高粘結性能，有機植筋被廣泛應用，而有機粘結材料的耐久性能和耐高溫性能較差，給結構埋下了安全隱患。
  18. Analysis of bonding strength of two room - temperature - curing wood adhesives

    兩種常溫固化木材膠粘劑膠接強度分析
  19. Morphological structure analysis indicates that the addition of pe - mah induces surface tension, makes phases uniformity, enhances bonding strength of interface and improves compatible property

    Sem分析表明，接枝物的加入，降低了界面間的表面張力，使兩相分散均勻，分散度提高，增強了相間的粘接力，改善了尼龍11與聚乙烯的相容性。
  20. Diamond core drill can be laser welded with full penetration and the bonding strength is 1500 n / mm2. dendrite morphology and porosity formed in the welds of al - fe - v - si aluminum alloy

    用本激光器對金剛石薄壁鉆進行焊接，可以將其完全焊透，抗彎強度為1500n / mm ~ 2 。
分享友人
分享到 Line

分享到臉書