bottom die 中文意思是什麼
bottom die
解釋
底模-
I had often stood on the banks of the concord, watching the lapse of the current, an emblem of all progress, following the same law with the system, with time, and all that is made ; the weeds at the bottom gently bending down the stream, shaken by the watery wind, still planted where their seeds had sunk, but erelong to die and go down likewise ; the shining pebbles, not yet anxious to better their condition, the chips and weeds, and occasional logs and stems of trees that floated past, fulfilling their fate, were objects of singular interest to me, and at last i resolved to launch myself on its bosom and float whither it would bear me
我常站在康科德河的岸邊，望著逝去的流水- - -它是一切過程的象徵，和宇宙，和時間及一切造物受同一法則的支配；那河底的水草隨著水流輕柔地彎曲，彷彿受到水底清風的吹拂，此刻還在水底紮根，但不久后就會凋零並隨波濤逝去；那閃亮的鵝卵石- - -它們還不急著尋找更好的去處，那砂石碎屑、藤蔓野草，和那偶爾從水面漂過、奔向命運盡頭的圓木、樹干，都使我產生了極大的興趣，我最終決定泛舟于康科德河的胸膛之上，隨它將我載去任何地方。 -
Nana described her own great happiness. her baby, the little louis, she said, was now at the house of her aunt, who brought him round to her every morning at eleven o clock, when she would take him into her bed, where he played with her griffon dog lulu. it was enough to make one die of laughing to see them both burying themselves under the clothes at the bottom of the bed
娜娜說孩子是她的最大快樂：他的寶貝小路易現在放在她的姑媽家裡，每天上午快到十一點鐘時，姑媽就把他帶來，她把他抱到床上，讓他在上面與她的捲毛狗呂呂一起玩，看見他們兩個鉆在被窩里的樣子，簡直笑死人了。 -
In different in terne die travel, the metal flow characterize in warm extrusion forming processes and the affection for the flow of metal stage which made by the difference between the blank bottom altitude and the axial direction limiting size in warm extrusion forming technique have been analysed we have gotten the equivalent strain field and the velocity field and other field variable that the blank in different in terne die travel and the die travel - load curve. at the same time, we have analyzed the contributing factor for the oil pump stator forming process optimized and achieve thereasonable die parameter for the war m extrusion forming finally, the optimized technics parameters were used into pilot production, then the qualified oil pump stator forging were produced, the analog results were compared with those of pilot production
論文具體分析研究了不同成形工藝過程中金屬流動的特點，並對不同凸模行程下溫擠成形過程中的金屬流動特點、坯料連皮厚度（底部高度）與溫擠壓成形工藝中的軸向界限尺寸的差值對金屬變形階段的影響進行了分析，獲得了坯料在不同凸模行程下的等效應變場、速度場等場變量及凸模行程-載荷曲線，同時對油泵定子成形過程的影響因素等進行了分析，優化並獲得了合理的溫擠成形工藝及模具參數。最後，利用模擬優化獲得的各項工藝參數進行生產實驗，得到實際生產出的合格油泵定子件，並將模擬結果與生產實驗結果進行比較。 -
Automatic slow cutting when the cutting plate presses downward and touches the cutting die, ensuring no size error between the top and bottom layers of cutting materials
裁斷機板下壓接觸刀模時自動慢切，使裁斷機最上層與最下層沒有尺寸誤差。 -
As he carried out his assignment he was ridiculed by people. he was intimidated by them. he was physically beaten by them and then he was finally thrown in the bottom of a mud filled cistern and left there to die
耶利米是一位領袖，神給他很艱苦的任務他執行任務的時候，不斷遭人嘲笑，他被他們嚇怕了，他被他們毒打，最後被丟進滿是泥濘的水槽，在那裡等死 -
Die centering in press is obtained by milling a slot on the bottom subplate parallel to the direction of the feed
通過在與進料方向平行的底部底板上銑出一個狹槽來實現壓床上模具中心的調整。 -
" now i have no future, " he says. " bottom line is, i can ' t stay in iraq. if i stay, this means i am going to die.
現在我沒有將來，他說，底線是我不能留在伊拉克。如果繼續停留的話，這將意味著等死。 -
Abstract : the paper introduces a forming process and design of progressive die for moveable spring used on a relay, and it carries on a process of double - layer forming and a way to protect useless stuff from jumping onto bottom plate
文摘:介紹了某繼電器中的動簧片成形工藝確定和級進模設計、在級進模中疊片成形及防止小廢料上帶的一種方法。 -
Value creativity, not money. view creativity as your company ' s true bottom - line, or your company will stop growing and die
注重創造，而不是錢。將創造視為公司的基本方針，否則公司會停滯不前或者走向死亡。 -
When creatures die, their salt is locked up in bones and shells, which drop to the bottom of the sea
而水族們死後沉入海底，它們體內的鹽分就被固定在骨骼和貝殼里。 -
Technological analysis and the die design for the bottom - body
下體壓鑄件工藝分析及模具設計 -
Does a quote also include top and bottom mounting plates ? or just the die set
一般報價包括標準模架嗎？還是只有沖裁模？
分享友人