buckling formula 中文意思是什麼
buckling formula
解釋
壓曲公式-
On the basis of this, the paper makes a great deal of calculation and analysis in this part, different parameters " effect and stress gradient are included. local buckling coefficient and the efficient width calculated formula are provided and look forward to take a reference to the redaction of the specification
本文對此內容進行了較為深入的研究，考慮了多個參數的影響，對各種應力比作用下的楔形腹板的屈曲及屈曲后強度進行了計算分析，得出了考慮翼緣相關作用的楔形腹板屈曲系數及有效寬度系數的計算公式，以期為規范的修訂提供參考。 -
In the formula, our experience in structural strength design and the experimental results are considered. and such factors are also considered as differences in materials of the skin and the reinforcer, effects of bending, torsion, stretching and offcenter of the reinforcer. furthermore, through post - buckling stress analysis of the skin, it is shown that even low stress level will result in buckling of the skin, but the skin still has loading capacity
在總結過去結構強度設計和試驗分析的基礎上，應用扁殼理論，在廣義力與廣義應變關系中考慮了蒙皮與加筋不同材料以及加筋的彎曲、扭轉、伸縮和偏心等的影響，推導出適合於工程應用的加筋殼結構軸壓屈曲臨界載荷的計算方法;並通過對薄壁結構蒙皮后屈曲應力分析，說明蒙皮在很低的應力水平時就出現失穩現象，但失穩后的蒙皮仍具有一定的承載能力。 -
Gabled frames are widely used in industry and civil engineering, it ' s web plates " local buckling calculated formula in the technical specification for steel - structure of one - storey light - weight buildings with gabled frames ( cecs102 : 98 ) are based on the rectangular plates " and did n ' t consider the interaction of the fringe plate. so, there are some different between the actual members and the prescript of the specification, and the post - buckling strength ' s calculated formula is based on the local buckling ' s, it must have some unreasonable
楔形門式剛架廣泛地應用於工業與民用建築中， 《門式剛架輕型房屋鋼結構技術規程》 （ cecs102 ： 98 ）中楔形腹板局部屈曲的計算公式來自矩形板，並且沒有考慮翼緣的相關作用，因此，規程中的規定與構件的實際工作狀況有一定的差異，且屈曲后強度的計算公式也是以局部屈曲系數為基礎的，勢必有其不合理性。 -
At first, the mechanical model of joint is discussed, and the constitutive relation of the rough joint, especially the bolt - supported joint, is given. then bedding slide of bedding stratified rock slope is studied adopting limit equilibrium method, and a formula of stability is brought forward. at last, the bedding stratified rock slope ' s buckling deformation and failure mechanism and its evaluating method of stability is investigated, a corresponding mechanics model is established, then detail research to this failure mode is made in theory combining the energy law and elastic stability theory of plate and beam, and an analytical solution of the yielding curve is educed from this model
文中首先對結構面的力學模型進行了一定的探討，提出了粗糙結構面尤其是加錨結構面的本構關系；然後採用極限平衡法，研究了順向層狀巖質邊坡的順層滑動失穩，提出了其穩定性計算公式；最後，結合能量定律和彈性板梁穩定理論，探討了工程中常見的順向層狀巖體邊坡潰屈失穩時的破壞機理、變形規律和穩定性定量評價方法，建立了相應的力學模型，求出了其相應的解析解，並提出了臨界坡長與最大彎曲位置的確定方法。 -
In the small deflection theory, by buckling analysis, the classical buckling critical load of integrative braid composite cylindrical shells under axial compression is get. according to the experience and the results of fem, a revised formula for calculating buckling critical load is presented
在小撓度理論中，通過前屈曲分析得到了完善的編織復合材料圓柱殼在軸壓情況下的經典屈曲臨界載荷，根據經驗及有限元計算結果，提出了計算屈曲臨界荷載的修正公式。 -
Local buckling capacity of steel composite beam subjected to combined bending, shear and patch loading is one of key problem in steel structures design. the computational formula for local stability of web was based on the assumption of infinite - elastic perfect plates in the steel structures design code ( gbj17 - 88 ). but in the revised code ( gb50017 - 2003 ), this formula was made big change with reference to british code ( bs5950, partl ) and australian code ( as4100 ), the related research result of our country was included as well. in the modified formula, influence of early geometric imperfection and elastic - plastic buckling stage were considered, which is compatible with both actual circumstance of engineering and the strength formula of beams under bending stresses ( considering partial plasticity of the section ). in this paper, the preceding problem is deeply analyzed and studied, considering the effects of various geometric parameters and stress combinations on buckling critical stress of web, the revised local buckling correlative formula for transverse and longituded stiffened web panels under combined stresses is analyzed and verified by finite element method
組合鋼梁腹板在彎、剪及局壓復合應力作用下的局部屈曲承載能力是鋼結構設計中需考慮的問題，新的《鋼結構設計規范》 （ gb50017 ? 2003 ）對此部分內容作了較大改動，原規范中關于腹板局部穩定的計算公式是基於無限彈性的完善板假定；新的規范則參考了英國規范（ bs5950 part1 ）及澳大利亞規范（ as4100 ）並結合我國相關研究成果，考慮了屈曲進入彈塑性階段以及初始幾何缺陷的影響。這不僅與工程實際情況相符，而且也與鋼梁在彎曲應力作用下允許截面部分進入塑性的計算公式相協調。 -
In these paper we use the following rule to determine the width - to - thickness ratio : if the local buckling has visible effect on the overall buckling capacity, then this width - to thickness ratio should not be exceeded based on the resul ts obtained, we proposed a new formula for the limitation of the ratio of h / tw of the t - section columns " webs
根據局部失穩對整體失穩不應該有顯著影響的原則，最後得到t形截面壓桿腹板的寬厚比限值計算公式。本文對規范修訂和工程應用有一定的參考作用。 -
( 2 ) the finite element program ansys is used to analyze the elastic buckling of rectangular tube, consequently the buckling load pcr and the simulating formula for the restraint coefficient &, is obtained. the results derived from the program are compared with the british standard and china standard
（ 2 ）採用有限元程序ansys對矩形鋼管板組進行了彈性屈曲分析，得出其臨界荷載p _ （ cr ） ，彈性屈曲模態與解析法所作假設相符，並擬合出均勻受壓下的矩形鋼管約束系數k _ 1的公式，並與英國規范和我國規范進行比較。 -
Based on theory of big flexibility defective close columnar shell, use adding partition board to resolve the partial buckling problem in partially cfst arch bridge ' s hollow steel tube segment. the formula of how to confirm the space between partition boards was deduced to content whole and partial buckling
在大撓度有缺陷閉合圓柱殼體局部穩定理論基礎上，提出採用增設橫隔的辦法以解決部分灌注鋼管混凝土拱橋中空心鋼管段的局部穩定問題，並導出了在同時滿足鋼管整體和局部穩定性的前提下，需增設橫隔的間距的公式。 -
The effects of lateral pressure and plate buckling mode are taken into account. when the tripping taking place, average stress - strain curves begin load shedding according to empirical formula
主要區別在於所用的單元性能曲線有所不同，以及對初始變形、殘余應力和側向載荷等影響因素的處理方法也各不相同。 -
The existence of perforation affects buckling characteristic and load capacity of members and makes the design formula different with that of non - perforated members
孔的存在導致薄膜應力的重新分佈，影響構件的屈曲特性和承載能力，使得無孔構件的分析與設計公式不再適用於開孔構件，因此有必要研究開孔構件。
分享友人