calibration component 中文意思是什麼

calibration component 解釋
校準組分
  • calibration : n. 1. 測定口徑。2. 刻度，標度，劃度數。3. 校準；標準化。
  • component : adj 構成的，組成的，合成的，成分的。 component motion 【物理學】分運動。 component part 組成部分...
  1. Study on multi - component calibration gases in ethene and propylene

    丙烯中多元標準混合氣體制備方法的研究
  2. On the part of the design of nine - component thrust vector stand, an automatic hydraulic pressure original position calibration system, a scheme of original position calibration, and the great rigidity universal flexible combinatorial underprop are designed. by using the scheme of “ universal flexible combinatorial underprop plus software digital filter ”, the inherent frequency of test stand is improved, and the problem of test stand libration is solved. then, the resolving method of the disturbance between underprops of the moveable frame is proposed, and the disturbance revise equation is deduced

    在推力矢量試車臺設計方面，設計了自動液壓原位校準系統、原位校準方案以及大剛度萬向柔性組合支撐;採用「萬向柔性組合支撐+軟體數字濾波」的方案，提高了試車臺動架的固有頻率，解決了試車臺動架的振動問題;提出了動架約束互擾問題的解決方法，推導了互擾修正方程;研究了九分力推力矢量測量誤差分析方法，並計算了推力矢量測量精度。
  3. When establishing the method, according to stipulations under each type, precisely weigh ( measure ) appropriate amount of impurity reference and component reference under test to formulate solutions testing impurity calibration factor, blend samples and record chromatograph chart, calculate calibration factor of impurity according to above mentioned method ( 1 )

    在建立方法時，按各品種項下的規定，精密稱（量）取雜質對照品和待測成分對照品各適量，配製測定雜質校正因子的溶液，迸樣，記錄色譜圖，按上述（ 1 ）法計算雜質的校正因子。
  4. Such impurities requiring calibration calculation normally use main component as reference and use relative retention time for orientation, such value are to be recorded under each type

    這些需作校正計算的雜質，通常以主成分為參照採用相對保留時間定位，其數值一併載人各品種項下。
  5. Main component self - compare without calibration factor can also be used when there is no impurity reference substance

    當沒有雜質對照品時，也可採用不加校正因子的主成分自身對照法。
  6. According to the study work of this paper, an automatic six - component strain gauge balance calibration system development scheme was put forwards : the system calibrates the balances in the ecs, and translates the loads to the bcs of the balances with measuring the balance ’ s position changes during the calibration

    本文根據1m高超聲速風洞氣動力試驗的總體要求，提出了採用天平校準載荷地軸系全自動加載、並通過天平空間位移測量將校準載荷換算到天平體軸系（ bcs ）的六分量天平校準系統總體研製方案，並確定了詳細的技術指標。
  7. This program is developed for single - component calibration and multi - component calibration with computing of calibration coefficients, data acquisition and basic data analysis

    可以用於單元校準和多元校準，計算校準系數，進行數據採集及初步的數據處理。
  8. Main component self - compare with calibration factor can be used when testing impurity content

    測定雜質含量時，可採用加校正因子的主成分自身對照法。
  9. In this paper, a 9 - point loading method been used in the new balance calibration system to load six component loads on a balance. at same time, the automatic loads method and the design of loading device are also important

    同時，在具有全自動加載功能的校準系統研製中，自動加載方式選取和加載機構的設計也是其中的關鍵技術難點之一。
  10. The automatic six - component calibration - loads loading system is one of the most important system of a balance calibration system, and how to load the six component loads on a balance is a difficult problem to deal with

    如何實現天平校準載荷六分量自動加載，是六分量天平校準系統研製的關鍵技術問題之一。本文選用了9加載施力點的加載方案實現六分量天平校準載荷的加載，保證各加載分量的精度指標相互協調。
分享友人
分享到 Line

分享到臉書