calibration unit 中文意思是什麼
calibration unit
解釋
校準單位- calibration : n. 1. 測定口徑。2. 刻度，標度，劃度數。3. 校準；標準化。
- unit : n 1 個體，一個，一人。2 （計值、組織、機構）單位；單元；小組，分部；【軍事】部隊；分隊。3 【機械...
-
This recent instrument includes a built-in fabry-perot interometer calibration unit with an automatic daily recording of a calibration signal.
這種最新儀器包括插入式的法布里-珀羅干涉儀定量部件，可以每天自動記錄一次定量訊號。 -
Contained within the ecm is a removable calibration unit, on programmable read-only memory.
包含在ECM內的是一個可動的校正裝置，或是可編程序的讀存儲器。 -
Additional time base calibration on the same unit
儀器本身的時基校正。 -
Ecu engine calibration unit
發動機校正裝置 -
Beckmann thermometers are designed to measure small temperature differences. hence the calibration of a beckmann thermometer refers to comparing the true temperature differences obtained from the laboratory s standard thermometers against the observed temperature differences indicated by scale readings of the unit under test
貝克曼溫度計是用於測量微細的溫差，因此本所將其標準溫度計所錄得的真正溫差與接受測試元件的標度讀數所顯示的觀察溫差進行對比，以校正貝克曼溫度計。 -
2. the necessity and difficulty are discussed for the in - place calibration of inertial measurement unit being subjected to the vibration, shock and acceleration induced by the host vehicles. a new in - place calibration method based on the fixed axe rotation constraint is presented
2 、討論了載體經受振動、沖擊和加速度的情況下，慣性測量組合參數現場標定的必要性和技術難點，提出了基於定軸轉動約束的現場標定演算法。 -
Contained within the ecm is a removable calibration unit, on programmable read - only memory
包含在ecm內的是一個可動的校正裝置，或是可編程序的讀存儲器。 -
The thesis finished a sample instrument used in measurement node. it is based on 8 - bit micro controller unit and has smart functions including auto calibration, auto scale change and auto balance of whetstone bridge. the data can be processed, stored, transferred and displayed in the sample device
本文完成了測試系統中基於16位微處理器的網關的硬體架構和軟體實時多任務內核的設計；研製了基於8位微處理器的具有自校正、自動量程轉換及測試電橋的自動調平功能的測試節點樣機；實現了測試節點的數據處理、存儲、顯示和傳送；繪制並編寫了測試節點的硬體電路圖和軟體源程序。 -
Calibration is generally performed by applying pressures of known values to the unit under test in sufficient number of steps ( normally about 7 ) distributed throughout its usable range, from lower test values to maximum calibration value, and then decreased backwards to initial test value
校正程序一般是對校正儀器引入已知的壓力。引入的壓力，在儀器的應用范圍內，逐級（通常為七級）提升至最大校正數值，然後逐級減少至最初之校正數值。 -
Several central modules in system design were introduced. the examination, parameter read - in and the unit calibration of the combined meter board were implemented, suiting for kinds of digital instrument
摘要論述了系統設計中的幾個主要模塊，實現了組合儀表總成校驗、參數寫入及電路板檢測，該系統適合各類數字儀表檢測。
分享友人