can coating 中文意思是什麼

can coating 解釋
罐頭內塗料
  • can : n 1 〈美國〉罐頭，聽頭（＝〈英國〉tin）；（裝液體的）鐵罐，玻璃罐（等）；一罐（之量）；茶杯。2 〈...
  • coating : n. 1. 被覆，表皮，塗層；包覆物；（食品上的）面衣，糖衣；塗料。2. 上衣料；細呢，花呢。
  1. The excellent quality of coating film based on waterproof two - component polyurethane coating filled with fly ash can be gained when the fineness of fly ash is 300 meshes

    當粉煤灰的細度為300目時能得到性能優良的雙組分聚氨酯防水塗料。
  2. At the same time, the machine can be used in lmitate the leather, coating ch - oth, bolting cloth and plush

    該機也可適應仿皮革、塗層布、篩網布、長毛絨等品種收卷使用。
  3. Arc sprayed aluminium composite coating can increase the service life of reaction caldron up to the design life

    採用電弧噴塗鋁復合塗層來解決反應釜的腐蝕問題，可使其達到或超過設計壽命。
  4. This product is the newest filming technique, the latest achievement of usa electronic magic, it utilizes decomposition principle of electronic material to form a positive negative ions film on the surface of car coating, which has high water repellency and makes the surface of coat has more than 95 % brightness of mirror surface, lt has preeminent performance on weathering resistance, ageing resistance, oxidation resistance static resistance and wear resistance, with the force of charged ions, this product can easy removes the dirt, water drop acid rain and grease on the surface of the film and perennially and effectively protect coat surface, lt is the fourth generation car beauty and protective product which replaces glaze sealing products

    本品屬于當今最新的鍍膜技術，屬美國電子工學魔法的最新成果，它利用電子物質的分解原理，在車漆表面生成持有高撥水性的正負離子覆膜，使漆面光亮度可達鏡面光澤的95 %以上，並具有超強的耐候性、抗老化、防氧化、防靜電、耐磨性極好的功能，它利用電離子的力量，可輕松彈去覆膜表面的污垢、水滴、酸雨、油脂等，平時只需清水沖洗，便可立即使之恢復離子效應，達到長期保護漆面的目的，是取代封釉的第四代汽車美容保護產品。
  5. The effect can be reduced by providing a generous fillet of cement around the edges of the coating.

    用粘接劑圍繞著貼片的邊界做一個緩和的內圓角，可使此種效應減小。
  6. Third generation product : a crylic - acid coating, it is environmental protection product, nontoxic and innoxious and its durability can last for 5 years

    第三代產品丙烯酸塗料，環保產品，無毒、無害，耐久性達5年左右。
  7. Fourth generation product : elastic thick film coating ( organic silicon a crylic - acid copolymeric - graft polymer ), it is a green and environmental protection product, and has nontoxic, innoxious characteristics, and its incredible durability can last at least for 10 years

    第四代產品彈性厚膜塗料（有機硅丙烯酸共聚接枝）綠色環保產品，無毒、無害、超耐久性，達10年以上。
  8. Incondition of surface anti - corrision and insulation coat of metal and tiny hole of steel where resistance and crack is very small, when supplying a high voltage, gas crack will be punctured and electric spark discharging will occur, now send a pulse signal to the alarming circuit the alarmer can send out sound and light to alarm. we can do leak hunting on the coating according to this principle

    金屬表面絕緣防腐層過薄、漏鐵及漏電微孔處的電阻值和氣隙密度都很小，當有高壓經過時就形成氣隙擊穿而產生火花放電，給報警電路產生一個脈沖信號，報警器發出聲光報警，根據這一原理達到防腐層檢漏目的。
  9. Solvent can be added to plastisol coating to lower the viscosity, producing organosol coatings

    可加入溶劑到塑性溶膠塗料中以降低它的粘度，形成有機溶膠塗料。
  10. The results of performance testing showed that the additive of nano - powders can evidently enhance the latex coatings " weathering resistance, scratch resistance, water resistance and alkaline resistance, and do not reduce other performances ; polybasic nano - composite powders have more efficient than single nano - powder ; the dispersing method have biggish effect on performances. observing the stability of nano - additive of exterior latex coating showed there was no viscidity rising, no delaminatiom sedimentation in two months. tryout by plant showed that nano - weatherability additive can obviously enhance the weathering resistance of latex coating and water resistance, and no reducing other capabilities

    對其性能研究的結果表明，納米粉體材料的引入，可以明顯提高乳膠漆的耐候性、耐洗刷性和耐水耐堿性能，對其它性能無不良影響；納米多元復合粉體比單一粉體的改性效果明顯；納米粉體的添加工藝對改性乳膠漆性能有較大的影響，採用同普通填料一致的添加方式制備的試樣與採用超聲波預分散后在配漆階段加入制備的試樣相比，後者在穩定性、耐候性等方面的性能都有所提高。
  11. Among various fabrication techniques of thin film, the sol - gel process has gained much interest for the preparation of pzt thin film, due to ihe advantages of good homogeneity, easy control of composition, low in - ill i reaving temperature, easy formation of large area thin films pb ( zrxti : - k ) 0 :, ( pzt ) films were prepared on the ito coated glass plates and low resistor silicon wafer in sol - gel dip - coating process associated wi di heat treatment : at different temperatures and characterized by x - ray diffraction ( xrd ) and transmission electron microscopy ( tem ). lt is shown that the pzt ferroelectric thin films with ( 110 ) preferred orientation and well - crystallized perovskite structure can be obtained after annealing at 680 ? for 30 minutes on ito substrate and at 800 " c for lornin on silicon substrate

    Pzt的制備方法有很多，其中溶膠?凝膠（ sol - gel ）方法可以和集成電路（ ic ）光刻工藝相互兼容，處理溫度低，有大面積塗敷性能，能精確地控制組分，無需復雜的真空設備，成本低廉，所以對于集成鐵電薄膜電容的應用這種方法有很廣闊的前景。本文利用sol - gel技術在摻錫的in _ 2o _ 3透明導電薄膜（ ito ）襯底和低阻硅襯底上成功地制備了pzt鐵電薄膜。運用了x射線衍射， sawyer - tower電路和lcr電橋分別對薄膜的晶化溫度，結構和電學性能進行了測試。
  12. The latter can form a coating that is resilient.

    后一種可形成一種有回彈力的塗層。
  13. The suitable additives recombination can not only improve considerably the quality of chromium coating, increase the brightness, current efficiency, dispersion ability and sedimentation velocity, but also enlarge the application scope of chromium plating technology

    採用適當的添加劑復合不僅可以顯著提高鍍鉻層質量，增加光亮度、電流效率、分散能力和沉積速度，而且可以擴大鍍鉻工藝范圍。
  14. Coating medium spraying, drying and exhauting can be carried out simutaneously for film - coating, the whole processing can be completed only in 1 - 2 hours and for sugarcoating, in 4 - 5 hours

    薄膜包衣能連續並同時進行噴灑包衣介質、乾燥、排風，只需1 - 2小時就可完成全部包衣工序，糖衣包衣只需4 - 5小時即可完成。
  15. Pdmaema can be cross - linked by quaternization to develop a positively charged dense network structure. according this mechanism, pdmaema / psf positively charged nanofiltration membrane was developed by interfacial polymerization using psf plate macrofiltration membrane as support layer, pre - polymer of pdmaema water solution as coating solution, p - xylylene dichloride / heptane as cross - linking agent

    根據這一機理，以psf平板微孔膜為基膜， pdmaema預聚物水溶液為塗層液，以對二氯芐正庚烷溶液為交聯劑，採用界面聚合法制備了pdmaema psf荷正電復合納濾膜。
  16. The adhesive force between the coating and the magnesium substrate can be improved significantly by using proper technique of zincification

    用浸鋅工藝能較好地改善鍍層與基體間的結合力。
  17. The problems can be addressed, in part, through a strongly reactive alloying addition, such as mg, li and so on, and through reinforcement coating. in this paper sicp / al composites and sicp / al - si composites fabricated by the pressureless infiltration method. in order to found out the influence the different quantity of the reactive alloying addition mg si ce on the wetting between sicp and molten metal as well as the properties of mmcs, the behaviors of molten metal, the mechanical properties, micro - structure and the interfacial reactions was investigated respectively

    本文通過研究制備sicp al復合材料、 sicp al - si復合材料的過程中，熔融鋁液或鋁硅合金液的浸滲行為、 sic - al 、 sic - al - si之間的界面反應、復合材料的機械性能、微觀結構等，探討了不同量的活性元素mg 、 si 、 ce對sic顆粒與熔融基體之間的潤濕性及復合材料性能的影響。
  18. We produce all kinds of aluminium profiles : such as bicycle and motorcycle rims profiles, rims profiles, industry profiles, work table, ladder, windows and doors profiles, construction profiles, radiators, aluminium tubes, plates, aluminium foil and so on, we can produce the surface according to your requirements : mill finish, anodized, electrophoresis, powder coating

    我們生產各種鋁型材:如自行車，摩托車鋼圈概況，鋼圈概況，工業概況，工作表階梯，門窗型材，建築型材，散熱器，鋁管，板，鋁箔等，我們可以生產表面根據你的要求:磨完成後，陽極氧化，電泳，粉末塗料
  19. The product is adopting the numerator that the united states first enter synthesize the craft, the numerator that pass science designs, make epoxy and water polyurethane the combination, form polymers has each other thing of wearing the network construction, and join the functional monomer to it make the product can polymerize in normal temperature ; make coating have excellent hardness, luster, chubbiness and attrition resistance, water resistance ， ethanol resistance ; make the water - paint with the product has epoxy and polyurethane excellent capability

    該產品採用美國最先進的高分子合成工藝，通過科學的分子設計，使環氧樹脂與水性聚氨酯分散體有機地結合，形成具有互穿網路結構的高分子聚合物；並通過功能性單體的引入賦予該產品常溫自交聯功能，使漆膜具有極好的硬度、光澤、豐滿度、耐水性及耐磨性，使配置的水性漆兼具聚氨酯及環氧樹脂的優異性能。
  20. Can coating, anti - corrosive equipment

    罐頭塗料，耐腐蝕設備
分享友人
分享到 Line

分享到臉書