cavitation range 中文意思是什麼

cavitation range 解釋
氣蝕區域
  • cavitation : n. 1. 【航空】氣穴現象；氣渦現象。2. 【物理學】成穴；空化，（超聲波的）空穴作用；【醫學】成洞，成腔。
  • range : vt 1 排列；整理（頭發等）。2 使歸類[班、行、隊]；把…分類。3 〈用被動形或反身形〉加入，站住…的一邊...
  1. The propeller cavitation range determined by calculation method presented in this paper agrees with the observation result of cavity image at cavitation tunnel very well, which proves the practicability of this method

    應用本文計算方法確定的螺旋槳空泡范圍經與空泡水洞中的空泡圖象觀察結果比較，證明了該方法的可行性。
  2. The characteristics of high pressure gyratory sprayed pumping discusses is presented, which is applicable in wide range of scope and ground layers, convenient for construction, long durability, wide source of materials. mechanism for subgrade strengthening : complex foundation of cement solid and earth between piles was formed by pulsant load of flowing pressure and spraying flow, water wallop, cavitation phenomenon, water wedge effect, extrusion force and air flow agitation etc so as to enhance foundation bearing force and reduce settlement and deformation

    高壓旋噴注漿技術具有適用范圍、適用地層較廣，施工方便，耐久性好，材料廣闊等特點；其加固地基機理主要是通過流動壓、噴射流的脈動負荷、水塊的沖擊力、空穴現象、水楔效應、擠壓力、氣流攪動等效應形成水泥固結體與樁間土的復合地基，從而提高地基承載力，減少沉降變形。
  3. Rotation - cavitation mechanism was outlined based on the experiment results and the essential conditions for the occurrence of auxetic properties in polyolefin blends were concluded as followed : firstly there must be at least two phases, the matrix can be soft materials which were able to be networks when being stretched, as well as suitable consistence must be provided between two phases. fracture stress work measurement was optioned to characterize the force between two phases. finally, the auxtic property repeatability of the blends was measured and the fact that the auxetic property could only occur in the elastic range was certificated by the result that only the specimens which were stretched for 5s, 10s had repeatability after being retained for 1 months

    實驗工作的最後一部分研究了體系負泊松比效應的可重復性，選取穩定的負泊松比共混體系在測試數據採集時間為55 、 105 、 155 、 205條件下進行測試，將樣條放置l天、 10天、 30天進行測試，測試結果表明，在5s 、 105條件下測試的試樣在放置一個月後泊松比測試結果具有可重復性，證實了體系的負泊松比現象發生在材料的彈性形變范圍內。
  4. Increasing ultrasound intensity in the range of cavitation threshold and cavitation peak value, decreasing monomer concentration and increasing the temperature make the induction period shorter. under optimized reaction conditions, the conversion of ba can reach 90 % in 11 min at high n2 flow rate the viscosity average molecular weight of the obtained pba reaches 5. 24 106. the molecular weight of pba varies with ultrasonic irradiation time, indicating that the ultrasonic induced emulsion polymerization is dynamic and quite complicated, polymerization of monomer as well as degradation of polymer occurs concomitantly

    一、實現了無常規化學引發劑存在下的超聲輻照引發丙烯酸正丁酯（ ba ）間歇乳液聚合，制備了pba納米粒子，在11min內轉化率達到90 ，分子量達5 . 24 10 ~ 6 ，隨反應時間的延長而降低，表明超聲輻照引發乳液聚合是一個動態的復雜過程，單體的聚合和聚合物的降解同時發生。
  5. To improve the efficiency of solution, the solution method to determine the cavitation range of blade is carried out for each chordwise string, the interaction between strings is included by spanwise iterative procedure

    為了提高求解效率，本文在確定螺旋槳槳葉上空泡范圍時採用的求解方法是針對每一個弦向「條帶」進行的， 「條帶」之間的相互影響通過沿槳葉展向的迭代考慮。
  6. To avoid or reduce these trouble induced by the unsteady cavitation, the theoretical design method for propeller and the blade section with the good cavitation performance are adopted to enlarge the cavitation bucket width and control the range and type of the cavitation on the blade. this enables propeller to operate in the non - uniform ship wake rather well

    為了避免或減緩空泡帶來的危害，採用螺旋槳理論設計方法和空泡性能優良的槳葉剖面來增加空泡斗寬度和控制槳葉空泡范圍及空泡類型，以適應非均勻流場中螺旋槳工作的需要。
  7. This paper has presented the calculation formula and numerical solution methods to determine the range and volume of partially cavity, supercavity by using surface panel method, and has predicted the range and volume of unsteady cavitation of propeller by using surface panel method for the first time inland

    本文敘述了應用面元法確定非定常螺旋槳局部空泡、超空泡的范圍和體積的計算公式和數值求解方法，在國內首次應用面元法預報了螺旋槳非定常空泡的范圍和體積。
分享友人
分享到 Line

分享到臉書