composite layer 中文意思是什麼
composite layer
解釋
復合層-
Effect of heat treatment on induced apatite deposition and bonding strength of the alkali treated titanium oxide layer for carbon carbon composite
碳復合材料上堿液處理氧化鈦鍍層誘導沉積磷灰石和結合強度的影響 -
By the methods of epn ( electronic probing needle ) 、 sem and xed, the formation mechanisms of the wear - resistant composite layer are studied, the results indicated that, molten iron has infiltrated into the alloying layer under capillary action. this caused ht powder, whose fusion point is low relatively, to be surperheated and formed a surface composite layer
利用電子顯微鏡及x射線衍射等試驗方法，研究了復合層形成機理，研究表明，復合層是在毛細力作用下，鐵液被吸入合金層中，致使低熔點ht粉過熱熔化而形成的，並與母材是冶金結合。 -
Nano - tiopc60r, 40nm / ctm / pc = l / 80 / 100, s762. 5nm = 0. 533cm2 / u j ) ; thereby the single - layer nanoparticle tiopc / fluorinone - based azo composite photoreceptors were prepared and their photoconductive properties were briefly studied. in conclusion, two originalities can be outlined from this thesis : ( 1 ) by using 1, 4 - dioxane as disperse solvent, stable and uniform composites of tiopc, azo, hydrzone and polymer matrix were prepared, and the single - layer photoreceptors were successively fabricated with these composites, the photoreceptors showed high and wide range photosensitivity from visible to near infrared spectral regions
綜上所述，本論文主要有以下兩個創新之處： （ ）採用兩雜性的二氧六環做分散溶劑，成功地實現了酞警氧鈦、綠丹藍偶氮、茶苯晚以及聚合物介質組成的、多相多組分體系的穩定復合，從而制備出從可見光到近紅外光區都具有高光敏性的寬頻響單層復合光導體。 -
A review of the development of organic semiconductor composite photo - conductive materials and devices was followed by a proposal of the researching theme in this thesis. the effects of fabrication arts such as solvents, gradient, interfacial layer and configurations on the photoconductive properties of the single - layer chlorodiane blue azo / tiopc composite photoreceptors were systematically studied in chapter ii. the results showed that the solvent played a decisive role in the multiphase and multicomponent system composed of two photogeneration species ( chlorodiane blue azo and tiopc ), a transporting material ( hydrozone ) and polymer binder ; 1, 4 - dioxane, as an amphiphilic solvent can effectively disperse and stabilize such multiphase and multicomponent systems, the derived photoreceptors presented improved photoconductive properties superior to those of dual - layer counterparts and demonstrated the evident synergetic enhancement and complementary effects ( eg
結果表明：在由兩種光生材料氯丹藍偶氮和酞菁氧鈦、傳輸材料萘苯腙以及聚合物介質組成的多相多組分復合體系中，分散溶劑是至關重要的因素，二氧六環作為典型的雙親性溶劑，有效地分散和穩定了該多相多組分復合體系，得到的復合單層光導體的光敏性在整體上優于雙層光導體，復合材料在可見光和近紅外光區分別表現出的偶氮和酞菁氧鈦的光敏性（如azo / tiopc = 8 / 2 ， cgm / ctm / pc = 1 / 120 / 120時，具有明顯的互補效應；在近紅外光區明顯高於酞菁氧鈦與偶氮光敏性的線性加和，表現出協同增強正效應。 -
The result of those studies as follow : ( 1 ) an composite layer of definite thickness on the casting was gained by cast - sintering technique, and it has well wear - resistance. ( 2 ) the reinforcement of the composite layer is tic or vc, which was exiguous and is well distributed
同時利用干滑動摩擦磨損實驗，對表面復合層的耐干滑動摩擦磨損的性能進行了研究。研究表明： （ 1 ）利用鑄造燒結技術可以在鑄件表面獲得一定厚度耐磨性能良好的表面復合層。 -
One is to improve the photoconductivity by annealing the mpc film under magnetic field ; the other is to form composite multi - layer film of zno / pbpc and sno / pbpc, to change the spectral response range of mpc films
一是通過磁場熱處理提高酞菁薄膜的光電導性能；二是通過將p型酞菁與n型材料異質復合，改變光譜響應范圍。 -
The study conducted research on the following four fields : firstly, the characteristics of the interfacial polymerization system of piperazine aqueous solution / trimesoyl hexane solution were systematically investigated. the results show that at a certain molar ratio between the two monomers, piperazine and trimesoyl, at the two phase interface, a dense functional layer of ultra low pressure, high permeating flux and high salt rejection formed by controlling the time of interfacial polymerization, such as the composite membrane ( i ), the concentration in water phase is 0. 4 %, and 0. 1 % in organic phase, and the polymerization time is 1 minute
本文主要進行了四個方面的研究，首先系統分析和研究了哌嗪水溶液均苯三甲酰氯正己烷溶液界面聚合體系特徵、界面聚合反應中各影響因素對膜性能的影響等，結果發現，當界面處兩相單體（哌嗪和酰氯）分子摩爾比為某一比值時，通過控制界面聚合時間（有機相處理時間） ，可以形成超低壓高通量高脫鹽的緻密功能層，如復合膜（ ） ，水相濃度為0 . 4 ，有機相濃度為0 . 1 ，聚合時間1min 。 -
It set up the development of the world recognized high performance nanofiltration composite membrane of aromatic polyamide, on the basis of reviewing the development, the importance in the membrane separation technology, the classification, the fabrication technique and the current development of the research and the application of the nanofiltration membrane. polysulfone was chosen as the material for making the porous substrate because of its excellent compress - to - denseness resistance, its cheap price and its great availability. by fabricating an ultra thin polyamide functional layer on the polysulfone substrate through interfacial polymerization taking piperazine as the monomer in aqueous phase and trimesoyl chloride as the monomer in organic phase, high performance nanofiltration composite membranes of ultra low pressure and ultra high permeating flux were prepared
選擇耐壓密性能優良，價廉易得的聚碸材料為制備復合膜基膜材料，哌嗪為水相單體，均苯三甲酰氯為有機相單體，通過界面聚合反應在基膜表面形成超薄功能層，制備了超低壓高通量聚哌嗪均苯三甲酰胺聚碸納濾復合膜，以0 . 1 mgso _ 4溶液為測試液，所得高脫鹽平板復合膜（ ）在0 . 4mpa下，脫鹽率為96 . 1 ，通量達85 . 2l -
The particles distributed hi the matrix of grey cast iron, but some contact each other. the composite layer extend gradually into the substrate. when volume fraction of wc is 36 wt % and 27 wt %, the matrix of the composite is high chromium cast iron, consist of white carbide bars and the austenite. wc particles distributed uniformly, retaining approximately quondam granular form in the composite layer which has an evident interface area with the substrate, with good bonding strength
對不同碳化鎢體積分數的灰鐵和低鉻鑄鐵基復合材料的微觀組織結構分析表明：碳化鎢體積分數為52時，復合層內基體為灰口鑄鐵組織，顆粒直接分佈在灰鐵基體上，部分碳化鎢顆粒有相互接觸的現象，基材與復合層之間沒有明顯的過渡；碳化鎢體積分數為36 、 27時，復合層內基體為高鉻鑄鐵，由面塊狀的奧氏體和白條狀碳化物組成，碳化鎢顆粒表面固溶於基體組織中，粒形基本保持完整，分佈均勻，與基體構成冶金結合，基材與復合層之間存在一個明顯的平緩過渡區。 -
Keywords : sedimentation velocity and potential, electrophoretic mobility, electric conductivity, charged composite particle, charged porous particle, arbitrary double - layer thickne
關鍵詞：沉降速度與電位、電泳可動度、電導度、帶電復合粒子、帶電多孔性粒子、任意電雙層厚度。 -
Through the analysis we found that the effect will become more obviously with the increase of thickness or width of superstratum and the decrease of the coefficient of foundation bed ; ( 3 ) anisotropy and nonlinear elastic f. e. m. model has been established and the effect of stress dispersion in compound two - layer foundation was analyzed on the base of the model. from the analysis we can conclude that the coefficient of subsidiary stress dispersion will amplify with the increase of thickness or width or stiffness of back - up coat ; ( 4 ) the formula which can be used in conventional calculation has been deduced for calculating the coefficient of subsidiary stress dispersion and it also has been affirmed to be reasonable through the checking calculation ; the whole theory of compound two - layer foundation has been brought forward in this paper and it ' ll enrich the theory of composite foundation
針對以上問題本文做了以下一些工作並得到若干結論： （ 1 ）提出了「復合雙層地基」的概念，並通過工程實例證明此概念的提出有其合理性和必要性； （ 2 ）用彈性地基梁理論證實了復合雙層地基確有應力擴散效應，且擴散效應隨上覆硬層厚度、剛度的增加而增大，隨下臥層基床系數的增大而減小； （ 3 ）建立了非線彈性、各向異性有限元模型，並以此為基礎分析了復合雙層地基的應力擴散效應，得到附加應力系數隨加固層厚度、寬度、剛度的增加而增大的結論； （ 4 ）推導了可用於常規計算的復合雙層地基應力擴散系數公式，並代入工程實例進行了驗證。 -
Application of composite ant colony optimization to two - layer pcb routing
布線的混合螞蟻優化方法 -
Technique and condition of developing membrane such as thickness of support layer, concentration of coating solution, coating time, ph value of coating solution, concentration of small molecular additive in coating solution, concentration of cross - linking agent, cross - linking time and composite times were studied
對制膜工藝條件如基膜厚度、塗層液濃度、浸塗時間、塗層液ph值、塗層液中小分子添加劑的含量、交聯劑類型、交聯劑濃度、交聯時間及復合次數對納濾膜性能的影響進行了研究。 -
At first, based on the results of in - situ load tests, the load - settle curves are acquired, and the effects of different reinforcement parameters are presented. these parameters include the linear density ratio ( ldr ) ; the location of the top layer of the geobelt measured from the bottom of the load plate ( u ) ; the different materials of geobelt ; the number of reinforcement layers ( n ) and the distance between the two layers of geobelt ( a h ). these results show that the bearing capacities of the reinforced composite foundation can be improved and the settlement can be reduced
首先，通過現場載荷試驗，獲取了加筋墊層復合地基荷載-沉降曲線，從筋帶鋪設的密度、筋帶的首層間距、不同筋帶材料、加筋層數以及雙層筋帶的層間距等幾個方面分析了以上加筋參數對加筋復合地基承載力的影響，指出筋帶的存在提高了加筋復合地基的承載力，減小了沉降。 -
The composite material, which is used to make muller plow of sand mill, is prepared by the method of cast - infiltration and the technology parameters for making composite material is optimized. then the effects of the matrix component on composite layer also are disccused
通過試驗對利用鑄滲法在鑄件表面獲得一定厚度復合材料層的形成機理進行了理論分析，優選了利用鑄滲法在鑄件表面制備復合材料的工藝參數（澆注溫度、合金膏塊的厚度、澆注位置等） 。 -
Microstructure of the composite layer was analyzed with help of optical microscope, scanning electronic microscope ( sem ), electronic probe microanalysis ( epma ) and x - ray diffraction ( xrd ). the compacting of the billet and the forming mechanism of the carbide reinforcement were studied based on thermodynamics and kinetics of reaction, sintering theory and the result of dta. at the same time, the wear - resistance of the composite layer was studied under condition of dry sliding friction
利用光學顯微鏡、掃描電子顯微鏡、電子探針以及x -射線衍射儀，分析了表面復合層的基體組織結構；運用反應熱力學、動力學、粉末燒結理論和燃燒合成理論，結合差熱分析結果，探討了表面復合層壓坯的燒結緻密化原理和碳化物增強相的形成機理；利用坯塊在真空燒結爐不同溫度下的燒結出來的顯微組織分析，模擬出坯塊的燒結過程中的化學反應過程。 -
With the correct compound designing, a composite layer with thickness of 1. 5to 6 millimeters was formed on the surface of casting by means of cast - sintering technique
通過合理的成分設計和工藝參數的優化選擇，利用鑄造燒結技術，在鑄鐵件表面獲得了一層厚為1 . 5 6mm的耐磨復合材料層。 -
Because of laser ' s transient heating and fast cooling on metal surface, laser cladding ceramic reinforced composite layer on titanium alloy surface can greatly improve wear resistance of titanium alloy
利用高能激光束對材料表面瞬間加熱和熔池快速冷卻的特性，在鈦合金表面用激光熔覆一層陶瓷增強復合材料，能夠顯著提高鈦合金的耐磨性能。 -
Preparating technique of nanocermet composite layer with method of ultrasonic - electrodepositing
超聲電沉積制備納米金屬陶瓷復合鍍層工藝 -
Martensite and austenitic form the matrix of the composite. ( cr, fe ) 7c3 is also a kind of reinforcement. ( 3 ) the combine of the composite layer and master - alloy is metallurgic combination and has a very high combining - intensity
（ 2 ）表面復合層內增強相tic或vc為原位生成，其顆粒細小，分佈均勻，無明顯梯度分佈或偏聚現象。
分享友人