composite reaction 中文意思是什麼
composite reaction
解釋
復合反應-
Arc sprayed aluminium composite coating can increase the service life of reaction caldron up to the design life
採用電弧噴塗鋁復合塗層來解決反應釜的腐蝕問題，可使其達到或超過設計壽命。 -
The structure evolution and reaction mechanism of silicon - iron composite powders treated at the temperature ranging from 700 c to 1200 c respectively were carefully investigated through xrd, sem, epma, dsc. it was found that the chemical formula, fe + si - fe ( si ) + fe3si ( si ), controls the reaction process, and the reaction mechanism of powder homogenization was clarified
通過利用xrd ， sem ， epma ， dsc等多種測試手段，詳細研究了鐵硅復合粉末帶材在700 1200的熱處理溫度條件下的反應狀況及結構變化，明確了反應過程中的化學方程式： fe + si fe （ si ） + fe _ 3si （ si ） ，並解釋了各個熱處理溫度范圍內，鐵硅粉末均一化的反應機理。 -
Sicp / al matrix composites, with 5, 15 and 25 % volume fraction of sic particles, were prepared by vacuum hot - pressing sintering processing in this paper. based on mechanics properties, sem observation and energy dispersive x - ray analysis, the interface reaction phenomenon of sicp / al composites made by vacuum hot - pressing sintering, as well as the reinforcement and fracture mechanisms of this composite were analyzed. the dynamic responses of sipc / al composites were studied by a split hopkinson high - speed pressure bar impact system which strain rate was from quasistatic state strain rate ( 3. 3 10 - 3s - 1 ) to dynamic state strain rate ( 5. 2 103 s - 1 )
本研究以武裝直升飛機防護裝甲材料為研究對象，採用真空熱壓粉末冶金燒結工藝制備了含sic顆粒體積分數分別為5 、 15和25的sic顆粒增強鋁基復合材料，結合其力學性能、掃描電鏡和界面微區能譜分析結果，分析了sic _ p al復合材料的真空燒結過程中的界面現象，以及材料增強和斷裂機理，並利用hopkinson高速壓桿沖擊實驗系統對其從靜態到動態（應變率為3 . 3 10 ~ （ - 3 ） s ~ （ - 1 ） 5 . 2 10 ~ 3s ~ （ - 1 ） ）的壓縮破壞響應進行了研究，分析了不同體積分數sic _ p al復合材料高應變率壓縮載荷下，材料的變形和微觀損傷機理，以及利用高速沖擊空氣炮測定了改復合材料制備剃度復合板的穿透性能。 -
The silver colloid in the composite material never changed the ability of zp to tune the potential of redox mediators. but the ability of the zirconium phosphate to adsorb neutral red and the redox reaction ability of this phenothiazine dye were enhanced significantly in the composite film due to the nanosize silver colloid
磷酸鋯降低了納米銀膠粒在水溶液中的聚集，提高了其催化活性，而銀膠粒保持了磷酸鋯對介體的電位調制能力，並大大的提高了磷酸鋯對堿性染料的吸附能力和染料分子的活性。 -
Using the semi - batch synthesis techniques, a grafting reaction mechanism is adopted to prepare a core - shell composite latex of siloxane / acrylate based copolymer
利用接枝反應和種子溶脹半連續滴加技術合成了聚有機硅氧烷聚丙烯酸酯復合乳液。 -
The binding principle in pelletizing covers a comprehensive model of interfacial reaction among particles inside green pellets, the formation of binding film during hardening of green pellets by baking to obtain enough strength for a volumetric catalyzed reduction model for cold - bound pellets bearing composite binder and corresponding high temperature reduction system in rotary kiln
提出了含復合粘結劑的生球強度界面作用力綜合模型，冷固球團礦強度的粘結膜機理，含復合粘結劑的冷固球團礦催化還原體積反應機制及全窯高溫快速還原熱工制度。 -
Afterwards, the authour studies the mechanism of cement power - sprayed piles composite foundation from the chemical reaction between cement particle and soil grain
並從水泥顆粒與粘土顆粒之間的化學反應方面，對粉噴樁加固軟土機理作了分析。 -
The results indicated that the dimension, shape and purity of base material could meet the functional demand of solid lubricant ; the thermal decomposition temperature of ptfe resin exceeds 400 c, but organic and inorganic packing filler added in ptfe made the water absorption rate of composite material increased, melting temperature and decomposition temperature decreased, in the meanwhile oxidative decomposition reaction was accompanied ; polar groups such as c = o, c - o - c and so on in the carbon fiber surface is advantageous to increase compatibility with other components and interlayer shearing strength ; uniform design experimental method could help to find the relationship between formula and frictional property by relatively small tests. the developing trend of each formula ' s friction coefficient could be showed by fitting curve ; the friction coefficient with no copper powder or graphite in formula was relatively big. this fact showed that copper powder and graphite should be used cooperatively ; it was found that when the ratio of copper powder to graphite by weight is 15 : 60, 30 : 30 - 40 and 60 : 15 - 30 respectively, the friction coefficient was relatively small. the degree of crystallinity of pure ptfe reached maximum by air cooling and the abrasion loss also reached maximum among three ones ; at the same time, the abrasion loss of solid lubricant sample was also the biggest among three ones ; when solid lubricant matched with 45 # steel axle or gcrl5 steel axle, lubricant transfer film could be formed on metal surface, thus direct contact between the surface of metal friction pair rings was reduced. their working life was elongated extremely ; there was mainly much graphite, a little ptff, moo3, feso4, cus and so on in lubricant transfer film
試驗結果表明：所選原料的尺寸、形狀及純度可滿足固體潤滑劑的性能要求；聚四氟乙烯樹脂熱分解溫度超過400 ，但在ptfe中加入無機填料會使復合材料吸水率提高，熔融溫度及分解溫度降低，且伴有氧化分解反應；碳纖維表面含有c = o及c - o - c等極性基團，有利於提高其與其它組分的相容性，提高層間剪切強度；均勻設計試驗方法能夠用較少的試驗次數找出配方與摩擦性能間的關系，擬合曲線基本能表示各配方的摩擦系數發展趨勢；配方中不加銅粉或不加石墨，其摩擦系數均較高，說明銅粉和石墨應該配合使用；當銅粉15份、石墨60份時，銅粉30份、石墨30 - 40份時，銅粉60 、石墨15 - 30份時，摩擦系數均具有較低值；純聚四氟乙烯樹脂在空氣冷卻時結晶度最大，磨損量也是三者中最大的；同時，固體潤滑劑試樣在空氣冷卻時的磨損量也是三者中最大的：不論是固體潤滑劑與45 #鋼軸配副或是固體潤滑劑鑲嵌入銅套后與gcr15鋼軸配副，在金屬表面均可形成潤滑轉移膜，從而減少金屬摩擦副表面間的直接接觸，大大延長其使用壽命;轉移膜中主要含有較多的石墨、少量聚四氟乙烯、 moo 。 -
The questions the researcher concerned are which system will be chosen and how to obtain the good lithium ionic conductor materials, which is the basic departure of the paper. the addition of second phase in composite can change the interface structure and the conduction mechanism, improve the matrix conductivity and other function such as the sintering, crisping and so on, so the research of composites are an interesting field of the ionic conductors. the synthesis of lithium ionic conductor is often by solid state reaction, but this method needs high temperature and leads to the volatility of lithium which not only causes the drift of the compounds but gets the no well - distributed materials
研究者所關注的問題是選擇新的體系進行研究，以期得到性能更好的鋰離子導體材料，這也正是本論文的基本出發點；復合離子導體中第二相的加入改善了基質的界面結構和導電機制，不僅可以提高基質材料的電導率，還可以在一定程度上改善材料的其它性能，如燒結性能、脆性和機械強度等。因此復合材料的研究是離子導體一個有廣闊前景的發展方向；合成鋰離子導體，特別是成分復雜的體系以傳統的固相合成法為主，但這種方法需要較高的溫度，容易引起鋰的揮發，從而造成產物組成的偏移，而且不易得到顯微結構均勻的材料。 -
The technique of producing metal matrix composite include powder metallurgy, casting ( including stirring casting process, in situ contact reaction process, liquid - phase metal infiltration process, co - spray deposition forming process ), reaction mechanic alloying process
制備金屬基復合材料的工藝分為粉末冶金法、鑄造法（鑄造法細分為攪拌鑄造法、原位接觸反應法、液相浸滲法、共噴射沉積法） 、反應機械合金化技術。 -
The experiments showed that wc and vc can dissolve mutually in the carbonizing reaction. when wc ' s content exceeds vc ' s, vc will dissolve into wc and make wc ' s crystal lattice bring aberrance and become wc1 - x, contrarily when vc ' s content exceeds wc ' s, wc will dissolve into vc and also make vc ' s crystal lattice bring aberrance. the surface cermet composite has high rigidity and well wear - resistance
（ 7 ）採用鑄造燒結技術，通過加入毗顆粒和v班一vc的原位放熱反應成功制取了碳化物陶瓷質量百分數超過60 %的表面金屬陶瓷材料，實驗證實wc與高溫碳化反應生成的vc相互可以很好的固溶，當wc的含量超過vc時， vc可以固溶到wc中，使wc的晶格發生畸變，成為昵卜: ，反之當vc的含量超過wc的含量時， wc可以固溶到vc中，也會造成vc的晶格畸變。 -
The sol - gel method and solid - state thermal reaction technique were used to prepare the composite oxides with variable lithium content. the doping treatments of some compounds were conducted. dta and tg were used to analyse synthesis mechanism, xrd to analyse phase composition, sem to observe morphology, li - b / licl - kcl / oxide simulated thermal cells to analyse the lithium - intercalation mechanism and properties of cathode material
實驗中採用溶膠?凝膠工藝和固相熱反應技術制取相應的不同鋰含量的復合氧化物，並嘗試對某些化合物進行適當的摻雜處理，應用dta和tg分析合成機制、 xrd分析所得物的物相組成、 sem觀察其形貌，模擬li - b / licl - kcl /氧化物的單體熱電池來分析陰極材料的嵌鋰機制及其電極性質。 -
The powder reaction and the composite and condone reaction are thought to be the main reasons to get the high property. by mathematically analyses ratio - strength of concrete that ground high - ti bfs contribute to the strength of concrete are varied with amount of powder in hpc. the more amount of powder is above 20 percent, the compression strength reduce gradually
同時，在本實驗的范圍內，微粉對高鈦礦渣混凝土強度貢獻率隨摻量的增加而增加；但強度值與摻量之間存在最佳摻量20 ，超過20時混凝土強度隨礦渣微粉摻量增加而下降。 -
In cuo + sio2 + tio2 / al reaction system, the element ti which is replaced in the reaction makes the microstructure of composite thin and the matrix strong. the mechanical properties of the composites fabricated by this reaction system are much finer than the ones fabricated by cuo + sio2 / al and cuo + tio2 / al reaction system. in cuo + tio2 / al reaction system, the wild phase al3ti is very large and it is disadvantageous to the improvement of composites " properties
在四種原位反應體系中， cuo + sio _ 2 + tio _ 2 al原位反應過程中被置換出來的金屬元素ti細化了基體組織，並起到了固溶強化的作用，所制備的復合材料的微觀組織與機械性能明顯優于cuo + sio _ 2 al與cuo + tio _ 2 al原位反應體系所制備的復合材料。 -
A polyurethane radical composite material ( pu / p ( vc - vac ) ) was synthesized by reaction of hydroxyl vinyl chloride - acetate copolymer ( p ( vc - vac ) ) and pu
摘要試驗研究了以羥基化的氯乙烯醋酸乙烯酯樹脂為改性劑，與聚氨酯預聚體反應合成聚氨酯基氯醋樹脂聚氨酯復合材料。 -
However the microstructures of the reaction existed before the heat treatment remained untouched. the heat treated fe - cu - c alloy - based composite sintered at 1100c was found to be a kind of ideal wear resistant material
1100燒結的fe - cu - c基復合材料進行熱處理后可以得到既具有良好的強度性能，又具有優良耐磨性的相對理想耐磨材料。 -
Citric acid, taking the place of hno3, solutes the substance which does not solute in solution, and it acts as the ligand of metallic ionic and the hydrolysis catalyst of si ( oc2h5 ) 4, which reduces the pollution caused by no2 which forms at the decompose process of the hot treatment. by changing the means of calcine of the drier gel, choosing the suitable temperature to burn the gel, the high temperature calcine time is shorted, which solves the question of the long period calcine. so the preparation process of the matrix and composite was finished by using more lower temperature than the traditional solid state reaction and more shorter time than the traditional sol - gel process
結果使基質和復合物的制備在比傳統的固相反應法低得多的溫度下和比常規的溶膠凝膠法短得多的時間里完成；五、對基質及復合物的干凝膠、粉體和燒結體進行了ir 、 dta 、 xrd 、 seni及交流阻抗譜表徵，研究結果表明：在溶膠向凝膠的轉化過程中同時存在著正硅酸乙酯自身的聚合作用和檸檬酸鹽絡合物之間的聚合作用：干凝膠向產物粉體的轉化在400600c之間進行；基質li 。 -
The epoxy resin modified by polysiloxane have the advantage of both polysiloane and epoxy resin, it have good heat - resistance, moisture - resistance, dielectric properties. to improve the heat - resistance and the strengthening of the composite, nano - sio2 has been add into the reaction system to modify the epoxy resin with polysiloxane
這種復合基體能有效得利用有機硅樹脂優異的耐熱性、耐候性、電絕緣性、憎水性、阻然性及耐寒性能，同時又具有環氧樹脂良好的粘結性、耐溶劑性及配伍性等優點。 -
Our main products include pure titanium heat exchanger, titanium steel heat exchanger, all kinds of condensers made of composite material, reaction kettle, titanium single or double pipe coil, titanium centrifugal ventilator, titanium impeller, fan, titanium corrugated pipe, tank, pipe heaters in various specifications, pipe parts, metal fillings, etc
本廠主要產品有全鈦換熱器鈦鋼換熱器復合材料各種規格的冷凝器反應釜鈦單雙層盤管鈦轉鼓離心機鈦葉輪風機鈦波紋管貯槽各種規格的管式加熱器各種規格管配件金屬填料等。 -
Micellar catalysis of the composite reaction the alkaline fading of crystal violet in ctab micellar solution
膠束對結晶紫褪色反應的影響
分享友人