compression pipe 中文意思是什麼
compression pipe
解釋
壓縮管- compression : n. 1. 壓縮；壓緊；濃縮，緊縮。2. 加壓；壓抑。3. （表現的）簡練。4. 應壓試驗。
- pipe : n 1 管，導管，筒。2 煙斗，煙袋；一袋煙。3 〈古語〉笛，管樂器；【航海】（水手長的）哨子（聲）；〈p...
-
Standard specification for compression joints for vitrified clay pipe and fittings
陶土管及其配件的承壓接頭標準規范 -
Specification for composite pipe compression fittings and compression joints for hot and cold drinking water systems
冷熱飲用水系統用復合管壓合配件和壓合接頭的規范 -
Specification for multilayer pipe type 2, compression fittings, and compression joints for hydronic heating systems
循環加熱系統用2型多層管壓合配件和壓合接頭的規范 -
Standard specification for multilayer pipe type 2, compression fittings, and compression joints for hydronic heating systems
水硬水泥混凝土和灰漿用乳狀和粉末聚合物改良劑的標準規范 -
Standard specification for multilayer pipe type 2, compression fittings, and compression joints for hot and cold drinking - water systems
冷熱飲用水系統用2型多層管壓合配件和壓合接頭的標準規范 -
For overterm service of unit equipment in thermal plant, taking high temperature compression part ( steam pipe ) for example, the paper introduced a three grade appraisal method and calculated the residual life of high temperature compression part using fixed asset linear method, establised a economic life mathematical mode, finally gave out a general economy appraisal for high temperature compression part with a calculation example
針對火力發電廠機組設備的超期服役，以高溫承壓部件蒸汽管道為例，以其運行工況為基礎，結合材質狀況，逐步實行三級評定，計算高溫承壓部件的剩餘壽命，利用固定資產線性折舊法對設備進行折舊計算，同時建立經濟壽命的數字模型，綜合評定高溫承壓部件的經濟性，並列舉了算例。 -
The 2 stroke book says because of testing, an 8 degree angle of divergence for the diffuser cone connected to the lead in pipe is the minimum angle to start with and 20 degrees for the compression cone at the other end of the pipe is a good starting point
二行程手冊測試，一個八度的漸縮圓錐反射角，連接導入氣管通道，是一個極小的開始角度，以及20度的壓縮圓錐在氣管的另一結束端，是一個好的開始 -
Pex specification for cold - expansion fittings with metal compression - sleeves for cross - linked polyethylene pex pipe
交聯聚乙烯管用帶金屬壓縮管套的冷擴張配件的規范 -
Tube and pipe fittings for engineering purposes - specification for olive type copper alloy compression tube fittings
工程用管與管接頭規范.第2部分:橄欖型銅合金耐壓管接頭 -
Tube and pipe fittings for engineering purposes - copper and copper alloys capillary and compression tube fittings for engineering purposes
工程用管與管接頭規范.第1部分:工程用銅與銅合金毛細管與耐壓管接頭
分享友人