cone type 中文意思是什麼

cone type 解釋
錐形（揚聲器）
  • cone : n 1 圓錐，錐形物；錐面；錐體。2 火山錐，圓錐形火山；錐狀地區。3 【植物；植物學】球果，球花。4 風...
  • type : n 1 型，類型，（工業產品的）品種；風格，型式。2 典型，榜樣，樣本，樣板，模範，範本；典型人物；具...
  1. According to the experimental data of droplet size 、 particle spectrum range 、 droplet cone shape 、 flow rate 、 cover area and cover area rate which obtained through changing the pressure of power sprayer and the nozzle diameter in greenhouse ， this paper made comparative analysis on atomizing performance in same pressure and different nozzle type between same nozzle type and different pressure. the conclusion is that : the ejection rate and the droplet cone shape change with the variation of pressure and nozzle diameter ， average particle diameter decreases obviously and particle quantity increases obviously with the increase of pressure and decrease of nozzle diameter. these results will lay experimental foundation for precise spraying 、 low pollution and highly effective operation

    本文根據溫室內動力噴霧機壓力與噴嘴孔徑的變化影響霧滴大小、粒譜范圍、霧錐形狀、流量、覆蓋面積及覆蓋面積率的試驗數據，對相同壓力下不同噴嘴型號和相同噴嘴型號時壓力不同時的微粒化性能進行對比分析和研究，得到如下結論噴出量與霧錐形狀隨著壓力和噴嘴孔徑大小變化而變化；平均粒徑隨著壓力的增加和噴嘴孔徑的減小而明顯減小；粒數隨著壓力的增加和噴嘴孔徑的減小而明顯增多，為精噴量、低污染、高防效的防除作業奠定了實驗基礎。
  2. A new type of joint technique between short _ net copper pipe and soft _ cable connection board, castfusion welding, is introduced. the practice of more than ten years shows that this fusion welding connection has the superiority of higher reliability, simpler processing method, better economy benefit compared to the taper cone face - contacted connection

    介紹了電石爐短網銅管與軟纜接線板之間的一種新型連接技術? ?澆鑄熔焊技術.經過10多年的運行，實踐證明短網銅管與鑄銅軟纜接線板的澆鑄熔焊連接，與傳統工藝採用的圓錐面接觸連接相比較，具有加工工藝簡單、運行可靠性高、經濟效益好等優點
  3. Lubricating nipples ; cone type

    錐形潤滑劑注油嘴
  4. On the base of deducing meshing theory, by simplifying the parameters and using software, the 3d model of the rolling cone - type toroidal drive is given. and the parametric models are realized. the assemble chart of drive is given

    在嚙合理論推導的基礎上，通過對滾錐齒超環面行星蝸桿傳動的各參數進行簡化處理，利用計算機軟體對滾錐齒超環面行星蝸桿傳動進行了三維實體參數化建模，實現了模型的參數化，給出了該傳動的裝配圖，並進行了動態模擬。
  5. Yd100 dynamic composite - cone loudspeakers of direct radiat type with two - magnet systems

    Yd100雙磁路復合盆直接輻射式電動錐形揚聲器
  6. Rules for the inspection of electrodynamic cone loudspeakerof direct radiate type for export

    出口直接輻射式電動錐形揚聲器檢驗規程
  7. For small aperture ejection nozzle, especially to the p serial type that the center hole diameter is 4mm, its center hole and inner cone is always adopting imported numerical control machine to grind

    對于小孔徑的噴油嘴，特別是直徑為4mm的p系列噴油嘴的中孔座面的磨削，一直採用進口的數控磨床加工。
  8. So in china research with investigate to adapt to the state of the nation, using above and all kinds of abandon biomass with the large quantity ' s resources of low quality and low price food economily, fleetnessly and high - efficiently to convert for that can act for on a certain degree the petroleum conversion of bio - fuel - oil theories with method, have important of economic meaning is with the social meaning, this text author is on check the foundation of the related data of domestic and international large quantity, proceeds living creature quality pyrolysis experiment that solve, established the pyrolysis solution to respond the dyn amics model, combine right turn the main design theories that equip of solution of pyrolysis of quality of rotating cone type living creature that parameter to proceeds the research, provided the theories the basis with experiment the data in the follow - up research

    因此，在我國，研究和探索適應國情，將上述各種廢棄生物質和大量的低質低價糧食資源，經濟、快速、高效能地轉化成可在一定程度上替代石油的生物燃油的轉化理論和方法，具有重大的經濟意義和社會意義。本文作者在查閱國內外大量相關資料的基礎上，進行了生物質熱解的實驗，建立了熱解反應動力學模型，並對轉錐式生物質熱解裝置的主要參數的設計理論進行了研究，為后續研究提供了理論依據和實驗數據。
  9. A new type hydraulic control system has been put forward in this thesis based upon analysis of working cases on the cone crushers. lt follows from research in this thesis that the new type hydraulic control system has some outstanding performances such as high automatic control level, reliability etc. and the new system has been successfully used in the auto - circling ultra - fine crusher developed by us in recently, too. and the time - lag problem on hydraulic control of the new system was studied in details

    對提高破碎設備的自控水平和增加整機的可靠性有顯著效果，同時又把該新型液壓系統有效地運用到我們所開發的一個項目? ?自循環超細粉碎機上，並對「時滯」問題做了研究。人工智慧技術近二十年來得到了很大發展，特別是專家系統，知識工程的發展更為迅速。
  10. The motion of the drive is also demonstrated. the paper mainly concludes the following works : the paper introduces the meshing theory of rolling cone - type toroidal drive and the motional relations of all parts, gives the formula of transmission radio. the relation between tooth numbers and helix angle of every parts is found out, and the assemble relation among all the parts is also given

    本論文主要包括以下內容：介紹了超環面行星蝸桿傳動的傳動原理及各構件間的運動關系，分蝸桿固定和定子固定兩種情況，給出了這種新型傳動的傳動比計算公式，得出了各輪齒數與計算圓處螺旋升角間的關系和各構件間的裝配關系，從而為該傳動的優化打下理論基礎。
  11. Interaction of cone signals on l - type horizontal cell in carp retina : experiments and modeling

    鯽魚視網膜亮度型水平細胞上不同視錐信號的相互作用:實驗及模型英文
  12. Firstly, in the luminosity - type horizontal cell ( lhc ) of isolated carp retina, we found : 1 ) repetitive red flashes progressively strengthened the synaptic connection between red - cone and lhc, whereas weakened that between green - cone and lhc ; 2 ) repetitive green flashes remarkably depressed the lhc ' s red response, but caused little changes in the cell ' s green response

    R / g型水平細胞（ r / ghc ）為一種色度型水平細胞，至於r / ghc與不同視錐的突觸迴路連接，經典的級聯模型認為r / ghc只接收來自綠敏視錐的直接輸入，對紅光去極化反應來源於lhc對綠敏視錐的負反饋。
  13. Cone - type flyer pay - off

    錐形越端放線裝置
  14. Building hoist. pinion and cone progressive type safety device

    施工升降機齒輪錐鼓形.漸進式防墜安全器
  15. The paper researches a new type mechanical transmission mechanism - the rolling cone - type toroidal drive. the meshing efficiency has been studied completely and systematically and the parameters of drive are optimized on the base of analysis about meshing. by taking advantage of computer technology the main parts of the drive - stator, planet gear and worm are modeled and emulated

    在對其進行嚙合分析的基礎上，對該傳動的嚙合效率進行了深入研究，並對該傳動進行了參數優化，進而利用計算機技術，對該傳動的主要零件? ?行星輪、環面定子和環面蝸桿進行了三維建模模擬，演示了該傳動的運動情況。
  16. Under the classic automatically control theorist ' s leading, the thesis establishes idiographic practice methods that using closed loop open type numerical control system to reconstruct the old hydraulic injection nozzle center hole and inner cone grinder

    在經典自動控制理論的指導下，制定了使用數控系統的全閉環控制方式來改造液壓中孔座面磨床的具體實施方案。
  17. Cone type loudspeaker

    圓錐形揚聲器
  18. In the paper, it mainly discusses how through redevelopment technique on the homemade open type numerical control system to successfully reconstruct an old hydraulic injection nozzle center hole and inner cone grinder, and make this declining machine obtain excellent capability

    本文主要論述了在利用即將報廢的液壓中孔座面磨床本體基礎上，使用國產開放型數控系統，經二次開發技術，成功地將其改造成性能優良的數控磨床的具體方法。
  19. Research and development of new - type cone crusher

    新型圓錐破碎機的研製
  20. Tape - wrapped type condenser cone

    帶包式電容錐
分享友人
分享到 Line

分享到臉書