conical angle 中文意思是什麼
conical angle
解釋
圓錐角-
Since complicated differential and integral operations were involved in the kernel of the integral equation, we simplified the equation and got the nakano equation. as instances, the planar archimedean spiral antenna, the planar equiangular spiral antenna, the monofilar helical antenna, the conical helical antenna with fixed ascending angle and the conical equiangular - spiral antenna were analyzed through the moment method. all of the results matched fairly well with the references and experiment results
這種方法的積分方程的積分核里含有復雜的微積分運算，為了簡化計算，本文在推廣的海倫積分方程的基礎上，對方程進行了簡化，推導了nakano方程，並以平面阿基米德螺旋天線，平面等角螺旋天線，軸向模圓柱螺旋天線，具有固定升角的圓錐螺旋天線和圓錐等角螺旋天線為例，用矩量法求解了天線上的電流分佈，研究了螺旋天線輻射的寬頻帶特性，所得的結果均與參考文獻吻合很好。 -
The glint suppression using high resolution range profile under conical angle measurement is studied, the angle information in signal components of scatters are extracted and averaged to suppress the glint. nonlinear kalman filtering methods under near spherical coordinate are analyzed and used to get more accurate tracking
研究了圓錐掃描測角體制下基於距離高分辨的角閃爍抑制方法，利用距離維高分辨像，提取強散射中心反射信號分量，在此基礎上估計出各個強散射中心的角度測量值，採用平均方法減少角閃爍對測角的影響。 -
The effects of r / h ratio, l / r ratio and cone angle on the dynamic response of the conical shells are discussed in this section
分析了圓錐殼結構的徑厚比、長徑比及錐角變化對結構應力響應的影響。 -
By means of analyzing the influence upon the stress distribution affected by parameters of half conical angle of anvil and ratio of height to diameter, the structural optimization method was advanced
通過分析頂錘半錐角、高徑比等參數對應力分佈的影響，提出了結構優化的方法。 -
Conical seating at an angle to flow is self aligning, tight and always closed in a no - flow situation. even in vertical ( flow - up ) pipe runs, this valve provides exceptionally tight shutoff
圓錐形閥座與流向具有一定的角度，能夠自行調整，在無流體狀態下能夠始終緊密關閉。甚至在垂直（流向朝上）管道上，這種閥門具有特別緊密地關閉特性。 -
The construction of conical nozzle is used by pump ' s delivery - valve, making use of the dynamic characteristics of conventional. short pipe to enhance injection pressure. there are three parameters of fuel injection system : response pressure, injection - advanced angle, injection valve bulge high degree, the best match was found by adjusting them
在油泵出油閥端，採取漸縮管結構措施，利用管路動態效應提高噴油壓力；對于噴油系統參數：噴油壓力、靜態供油提前角和油嘴凸出高度，三個參數進行調整試驗，找到它們的最佳匹配。 -
A mathematical model of flows in the substrate was established using the equivalent continuum approach, and multi - dimensional numerical simulation of the steady flows in the catalytic converters was performed. simulation results show that the separation and vortex, which cause the pressure loss and the velocity non - uniformity at the front of the first substrate, are generated near the wall of the conical pipe. in addition, the larger the inlet cones angle the more the pressure loss and maldistribution in converters, however, when the angle enlarges enough the pressure loss would be decrease
結果顯示氣流在擴張圓錐管壁附近出現分離產生較強的擾動，造成局部流動損失和載體前氣流速度沿徑向分佈不均勻；入口擴張管結構對催化器的流動特性有很大影響，但並非擴張角越大，催化器流速武漢理工大學碩士學位論文分佈的不均勻性和壓力損失也增大，而是存在著一個最佳角度，但當擴張角增大到一定程度以後，擴張角對流速分佈和壓力損失的影響變小。 -
In this paper, high resolution range steady imaging under the conical angle measurement, angle glint suppression under conical angle measurement, target recognition under momopulse angle measurement are studied
本文主要研究了圓錐掃描測角體制下距離維高分辨穩定成像，圓錐掃描測角體制下角閃爍的抑制，單脈沖測角體制下目標識別等課題。 -
Taking the meshing theory of conjugate curved surface as a foundation, utilizing array method of rotation transformation of vector, the meshing equation and contour surface equation of conical cam mechanism with swinging conical roller follower were analyzed and derived, and the calculation formula of pressure angle and synthetic curvature of the mechanism was presented, thus laid a solid theoretical foundation for enhancing the machining accuracy of conical cam, improving its processing method and achieved the integration of cam cad / cam
摘要以共軛曲面嚙合理論為基礎，運用矢量的旋轉變換矩陣法，分析並推導了圓錐滾子擺動從動件圓錐凸輪機構的嚙合方程和廓面方程，並給出了機構的壓力角和綜合曲率的計算公式，為圓錐凸輪加工精度的提高，改進其加工方法，實現凸輪cad / cam一體化奠定了堅實的理論基礎。
分享友人