contact of curve 中文意思是什麼
contact of curve
解釋
曲線相切-
In chapter four, according to the analysis on the boundary theory and velocity field of main fluid zone of two - phase fluid pumps, the parameter equations of vane ' s modular curve of centrifugal pump are given, which contact the boundary " layer and eular theory of two - phase fluid pump by the fixing angel of vane as variable and leading into the velocity coefficient a. the results show that, in designing process of vane ' s modular curve of centrifugal pump, the determination of the total shape and parameters relates the flow properties of two - phase fluid and output ability of pump, or the design of the modular curve of centrifugal pump is the kernel of hydraulic design
第四章依據固液兩相流泵的邊界層理論及對主流區速度場的分析，給出了離心泵葉片型線的參數方程；它是以葉片安裝角為參變數，以引入的速度系數k _ v作為中間因子，將兩相流泵的邊界層理論和歐拉理論聯系起來? ?它說明了這樣一個事實，在離心泵葉片型線的設計過程中，它的整個形態或參數的確定都關繫到兩相流體的流動特性和泵的輸出能力，或者說，離心泵型線的設計是其水力設計的核心。 -
Established the system of coordinates of roll testing, getting the parameters of equation of tooth face by solving the non - linear equations set ; according to the differential geometry and meshing principle, deduce the curvature parameters of tooth face and tooth profile, and get the parameters of instantaneous contact ellipse. emulate the contact trace and contact area of the working tooth face, and drawing the instantaneous drive ratio error curve
建立了克林貝格擺線齒錐齒輪嚙合分析的對滾模型，通過對非線性方程組的迭代求解，得到齒面方程的各個參數;由微分幾何和切齒嚙合原理推導了齒面上齒廓和齒線方向的曲率參數，得到了瞬時接觸橢圓的參數。根據設計參數和機床調整參數繪制了工作齒面的接觸軌跡和接觸區圖形，並求得了瞬時傳動比的誤差曲線。 -
The results indicated that the dimension, shape and purity of base material could meet the functional demand of solid lubricant ; the thermal decomposition temperature of ptfe resin exceeds 400 c, but organic and inorganic packing filler added in ptfe made the water absorption rate of composite material increased, melting temperature and decomposition temperature decreased, in the meanwhile oxidative decomposition reaction was accompanied ; polar groups such as c = o, c - o - c and so on in the carbon fiber surface is advantageous to increase compatibility with other components and interlayer shearing strength ; uniform design experimental method could help to find the relationship between formula and frictional property by relatively small tests. the developing trend of each formula ' s friction coefficient could be showed by fitting curve ; the friction coefficient with no copper powder or graphite in formula was relatively big. this fact showed that copper powder and graphite should be used cooperatively ; it was found that when the ratio of copper powder to graphite by weight is 15 : 60, 30 : 30 - 40 and 60 : 15 - 30 respectively, the friction coefficient was relatively small. the degree of crystallinity of pure ptfe reached maximum by air cooling and the abrasion loss also reached maximum among three ones ; at the same time, the abrasion loss of solid lubricant sample was also the biggest among three ones ; when solid lubricant matched with 45 # steel axle or gcrl5 steel axle, lubricant transfer film could be formed on metal surface, thus direct contact between the surface of metal friction pair rings was reduced. their working life was elongated extremely ; there was mainly much graphite, a little ptff, moo3, feso4, cus and so on in lubricant transfer film
試驗結果表明：所選原料的尺寸、形狀及純度可滿足固體潤滑劑的性能要求；聚四氟乙烯樹脂熱分解溫度超過400 ，但在ptfe中加入無機填料會使復合材料吸水率提高，熔融溫度及分解溫度降低，且伴有氧化分解反應；碳纖維表面含有c = o及c - o - c等極性基團，有利於提高其與其它組分的相容性，提高層間剪切強度；均勻設計試驗方法能夠用較少的試驗次數找出配方與摩擦性能間的關系，擬合曲線基本能表示各配方的摩擦系數發展趨勢；配方中不加銅粉或不加石墨，其摩擦系數均較高，說明銅粉和石墨應該配合使用；當銅粉15份、石墨60份時，銅粉30份、石墨30 - 40份時，銅粉60 、石墨15 - 30份時，摩擦系數均具有較低值；純聚四氟乙烯樹脂在空氣冷卻時結晶度最大，磨損量也是三者中最大的；同時，固體潤滑劑試樣在空氣冷卻時的磨損量也是三者中最大的：不論是固體潤滑劑與45 #鋼軸配副或是固體潤滑劑鑲嵌入銅套后與gcr15鋼軸配副，在金屬表面均可形成潤滑轉移膜，從而減少金屬摩擦副表面間的直接接觸，大大延長其使用壽命;轉移膜中主要含有較多的石墨、少量聚四氟乙烯、 moo 。 -
4 ) based on the theory analysis of the equal contact stress inner curve, the experiment research is discussed, and the project of experiment is also designed
（ 4 ）在理論分析等接觸應力軌道曲線的基礎上，對試驗研究進行了探討，並設計了相應的試驗方案。 -
2 ) applied hertz theory and the force between roller ( or ball ) and orbit, the equation groups for calculating equal contact stress curve are listed. the answer of the equation groups is calculated by utilizing the software matlab. the result of the simulation to this answer proved that the answer is reasonable and the design rule also be discussed from the analysis result
（ 2 ）應用赫茲接觸理論和所求得的軌道與滾動體之間的正壓力，分別列出以球和滾子作滾動體的等接觸應力軌道曲線方程組，利用matlab求解方程組，並對求解結果進行模擬分析，論證了所求的結果在理論上的合理性，歸納出設計這種液壓馬達的注意事項。 -
3 ) based on the analysis result of equal contact stress curve and the theory of elasto - hydrodynamic lubrication, the expression of the oil film thickness between roller ( or ball ) and orbit are calculated. the simulation result proved that the thickness of oil film is enough for bearing and lubricating
（ 3 ）基於等接觸應力曲線的求解結果和彈性流體動力潤滑理論，求得滾動體和軌道曲線間的油膜厚度表達式，並通過模擬分析論證了馬達正常工作時這種油膜能滿足承載能力和潤滑的需要。 -
To directly estimate the life of this kind of motor, and to design a orbit curve with the longest life at same condition, this paper gives theoretic research of the equal contact stress inner curve of radial piston motor. the research is divided into four parts : 1 ) taken all forces the piston endured into consideration when radial piston motor working, the force between roller ( or ball ) and orbit is deduced. the simple style of the press expression can be confirmed by ignoring minor influence factors after analysis all factors that will influence this press
靜壓傳動技術在各類工程機械中得到廣泛的應用，對作為其核心部件的徑向柱塞式低速大扭矩液壓馬達的研究顯得十分重要，為了能直接對這種馬達進行壽命估計，並能在相同工況下求得壽命最長的軌道曲線，本文從設計等接觸應力內曲線的角度對這類馬達作探討性的研究，主要從以下四個方面進行： （ 1 ）綜合考慮徑向柱塞式液壓馬達工作時的各種主要受力狀況，對柱塞組件進行受力分析，並通過模擬分析影響軌道和滾動體間正壓力的各個因素，得到正壓力的簡化表達式。 -
Works on the bending roll system of four - roll rolling mill, the workroll shape variation caused by the force of bending roll and the contact stress between rolls was researched with the fem software ansys, the maximum deformation of the work roll was calculated, and the curve of the gap adopting the least - squares method was fitted, which set the base of the further calculation of load - gap shape
摘要以四輥軋機的彎輥系統為研究對象，利用有限元分析軟體ansys研究彎輥力和輥間接觸應力引起工作輥形狀的變化，計算工作輥彎曲的最大變形量，並用最小二乘法對輥縫曲線進行擬合，為進一步計算有載輥縫形狀提供可靠的理論依據。 -
In this paper, wheel - rail rolling contact creepages and creeps of independently rotating wheel are analyzed, the effects of lateral and yaw motions of independently rotating wheel, and the curve radius to creepages of wheel - rail rolling contact are emphasisatically researched. 4
論文對獨立旋轉車輪的輪軌滾動接觸蠕滑率/力進行了分析，研究了輪對橫移和搖頭運動以及曲線半徑對獨立旋轉車輪輪軌蠕滑率的影響情況。 -
At first the paper begin to study the foundation of digital curved face and space meshing principle, introduce the basic knowledge of curve theory and curved face theory, explain the mathematical tools of vector turning and coordinate conversion in the paper ; analyse the motion and relative motion of rigid body, provide the condition of gear driving continuous contact and equation of conjugate meshing
論文首先從參數化曲面和空間嚙合原理基礎出發，介紹了曲線論和曲面論的基本知識，對課題研究重的數學工具矢量回轉和坐標變換進行了說明;分析了剛體的運動和相對運動，根據空間嚙合原理給出了輪齒傳動連續接觸的條件和共軛條件方程。 -
This paper has described the principle of the contact polarization curve method and the technique for measuring basic parameters, analyzed the influence of such factors as oxidation conditions of the ore deposits, arrangement of electrodes and structures of orebodies on the basis of studying some typical polarization curves, inferred several parameters such as independency of orebodies, reacted minerals, effective areas of reacted minerals, reserves of elements and grades of elements for some measured typical curves, and compared the inferences with the exploration results
摘要介紹了接觸極化曲線法的原理及基本參數的測取方法；通過一些典型極化曲線，對礦床氧化狀態、電極排布、礦體結構等因素的影響作了分析；對所測得的部分典型曲線進行了礦體獨立性、反應礦物、反應礦物有效面積、元素儲量、元素品位等參數的推斷，並將推斷與勘探結果進行了對比分析。 -
The character of the reservoir is typical of low permeability, high stress - sensitive, high capillary pressure value, steep capillary pressure curve, high critical water saturation, blur gas - water contact
物性特徵表現為滲透率低且對應力敏感，毛管壓力高，毛管壓力曲線陡峭，臨界水飽和度高，氣水界面模糊。 -
Proceeding with the support " s force condition is analysed in the static and revolve state, the stress distributions in the contact areas of support and roller are researched by way of hertz theory, the tow - dimensional elastic movement of the contact area is studied by contact mechanics, and the formula and curve of movement regulation are deduced
從回轉窯靜止與運轉時支承的受力情況分析著手，依據赫茲接觸理論對托輪與滾圈接觸區的壓力分佈進行了分析，並用接觸力學方法研究了接觸區的二維彈性滑動，推導出回轉窯軸向下滑計算公式，從而得出回轉窯軸向下滑特性曲線。 -
Firstly, a simple and practical representing method of the tooth edge tangential vector is applied to replace the traditional differential formula, the simple solving technique of edge contact problem makes the geometric edge contact analysis of the complex curve surface realize. secondly, using numerical searching and mathematical programming method solves the contact directions and loaded contact problem. finally, whole numerical simulation method is provided for loaded tooth contact analysis of high contact ratio spiral bevel gears
首先以一種簡單實用的輪齒邊緣切矢量的數學表示方法取代了經典的微分表達式，大大簡化了幾何邊緣接觸的求解，使復雜曲面的幾何邊緣接觸分析得以實現；其次又採用數值搜索與數學規劃法求解了邊緣接觸的主方向和承載接觸問題，為高重合度弧齒錐齒輪承載嚙合全過程的數值模擬提供了完整的方法。 -
Contact of curve
曲線相切 -
Abstract : this paper takes the manufacturing of non - circular gear as an example to analyze the non - circular gear ' s tip curve error influence upon it s contact ratio which is manufactured by involute cylindrical shape cutter, and it provides a theory basis to control strictly non - circular gear ' s contact ratio
文摘:以非圓齒輪插齒加工為例，分析了利用漸開線圓柱插齒刀加工非圓齒輪時齒頂曲線誤差對非圓齒輪重合度的影響，為嚴格控制非圓齒輪副的重合度提供了理論保證。 -
The load - deflection curve, the load - strain curve, earth pressure and distribution of sub - grade contact pressure under concentrated load, moving load and load at the side of the coal unloading chute respectively are obtained and discussed ; the whole process from cracking to failure are studied
分別對其在集中荷載、移動荷載及堆載等作用下的側向土壓力、基底反力的分佈情況以及結構構件的荷載?應變規律、荷載?撓度變化規律和結構從開裂到破壞的全過程進行了試驗研究和理論分析。
分享友人