cooling disk 中文意思是什麼
cooling disk
解釋
冷卻溜盤-
4 ) in a pre - swirl rotator - stator cavities with discrete pre - swirl nozzles and blade - cooling entry holes, the influences of pre - swirl angle and flow parameter on the flow and heat transfer characteristics were numerically investigated. the correlation for average nusselt number vs rotating reynold number or non - dimensional mass flowrate were established. the results show that : advantage of per - swirl inflow is the effect of cooling the blade - cooling entry holes ; pre - swirl inflow increases heat transfer in rotating disk of pre - swirl chamber ; as pre - swirl angle increases, local nusselt number decreases in pre - swirl chamber ; the temperature of stator of inner rotator - stator chamber and per - swirl chamber decreases as rotating reynold number increases ; when the axial mass flowrate maintains constant, heat transfer in the rotating disk of inner rotator - stator cavities does n ' t change as per - swirl mass flowrate increases, while heat transfer in the rotating disk of per - swirl chamber increases ; when the pre - swirl mass flowrate maintains constant, change of the axial mass flowrate has effect on the whole cavity
結果表明，預旋進氣的優點在於增強了葉片冷卻孔附近的對流換熱效果，局部努謝爾數隨預旋角的增大而有所減小；隨旋轉雷諾數的增加，不論是內轉靜腔室還是預旋腔室的靜盤上的溫度都不同程度的降低：當軸向中心進氣質量流量不變時，隨預旋進氣的質量流量增加，內轉靜腔室的轉盤盤面上的換熱基本沒有變化，而預旋腔室的轉盤盤面上的換熱效果增強；當預旋進氣質量流量不變時，軸向中心進氣的質量流量的改變對整個盤腔都有影響。 -
The degrees of crystallinity of pure ptfe under the different conditions of water cooling, air cooling and furnace - varying cooling were made comparison by xrd. the thermal stability of pure ptfe and solid lubricant was analyzed by dsc - tg ; the composition and valence state of elements in the surface of carbon fiber, solid lubricant before and after friction test and lubricant transfer film were characterized by xps ; the frictional property of solid lubricant was tested by pin and disk test rig. the frictional wear property of solid lubricant between embedded bearing sleeve and steel axle friction pair ring was tested by special simulate test machine, the hardness of solid lubricant was tested by pm ; the compression strength of solid lubricant was tested by material test machine
用sem表徵原料微觀結構、摩擦表面及潤滑轉移膜表面形貌：用xrd進行原料物相分析，及比較水冷卻、空氣冷卻、隨爐冷卻三種工藝條件下的純聚四氟乙烯樹脂的結晶度；用dsc - tg分析純聚四氟乙烯樹脂及固體潤滑劑的熱穩定性；用xps表徵碳纖維表面、固體潤滑劑摩擦前後表面、潤滑轉移膜表面的元素組成、價態變化；用銷盤式摩擦磨損試驗機對固體潤滑劑進行摩擦性能測試；採用專用的臺架模擬試驗機對固體潤滑劑鑲嵌軸承套與鋼軸摩擦副間的摩擦磨損性能進行測定；用萊次偏光顯微鏡（ pm ）測試固體潤滑劑的硬度；用材料試驗機測試固體潤滑劑的抗壓強度等。 -
Engine and performance : two stroke air cooling engine, powerful ; key parts imported, reliable and durable ; excellent start - up performance of no less than three times ' drawing, easy and convenient to operate ; chain wheel drive, minimum power loss ; constantly variable speed and disk brake guarantee your safety
動力性能：風冷二沖程發動機，功率強大，多種進口件組裝，性能穩定可靠，壽命長；優異的啟動性能，保證您不超過三次拉動，即可啟動發動機；採用無級變速裝置及性能優良的碟剎系統，使整車運行安全可靠，操縱方便；鏈式傳動，令功率損失減至最小。 -
Discharge - sand gate offers double disk cooling system creditable condition for low temperature ; when sand temperature is very high, it can change the way of discharge - sand gate into intermittent type : put rating sand to double disk and spray water for falling temperature until temperature falls designed range ; open the discharge - sand gate and discharge sand ; and then takes anther cycle ; this type has good effect after real testing, which is the effective way for exerting cooling function of double disk
卸砂門這種控制方式給雙盤冷卻系統的可靠降溫提供了條件，當型砂溫度較高時可將卸砂門改成間歇式的，先將雙盤內加入給定的砂量，噴水后直到溫度降到給定的范圍后，卸砂門打開將砂子卸出，然後進行下一循環，這一方式經實際運行驗證效果良好，是充分發揮雙盤冷卻作用的有效途徑。 -
Brief introduction of double disk humidification cooling control system
一雙盤增濕冷卻控制系統簡介 -
The system controls water - spraying quantity through measuring old sand temperature and current of double disk engine, which makes old sand have low temperature and average moisture after cooling
系統是通過檢測舊砂的溫度以及雙盤電機電流來控制噴水量，使經過冷卻后的舊砂溫度低水分穩定均勻。 -
The flow characteristics of rotor - stator cavity system with blade - cooling flow and disk - cooling flow was experimentally studied
摘要採用實驗方法，對具有中心進氣、兩個出口的盤腔系統的流動特性進行了研究。 -
It is common that double disk cooling of foundry plants lacks creditable water feeding equipment in long period ; therefore, it has poor cooling effect that has influenced application of double disk cooler
長期以來，國內鑄造廠使用的雙盤冷卻大都缺少一套可靠適用的加水裝置，所以降溫效果不理想，影響了雙盤冷卻的推廣使用。 -
The following is discharge - sand gate picture of water spray cooling control system of double disk cooling machine in laidong offered by our company
以下是我們為萊動提供的雙盤冷卻機的噴水冷卻控制系統的卸砂門照片： -
The influences of disk rotational speed, mass flow rate of inlet and presence of the blade - cooling holes on the flow characteristics in the cavity were investigated
結果表明：在本實驗范圍內，靜盤表面靜壓沿半徑方向先減小，后增大。
分享友人