core bending 中文意思是什麼

core bending 解釋
型芯彎曲
  • core : CORE ＝Congress of Racial Equality 〈美國〉爭取種族平等大會。n 1 果心。2 （事物、問題等的）中心，...
  1. Conducting wire core composed by thin brass wires or tinning brass wires, it is very soft. surface of part leads wraped mylar isolation layer, in case affecting their bending performance

    導電線芯採用較細的銅絲或鍍錫銅絲束絞組成，導線極其柔軟，部分產品的導線表面包有聚脂薄膜隔離層，以免絕緣橡皮嵌入其邊縫中而影響彎曲性能。
  2. Study on fatigue behavior of sandwich beams consisted of aluminum foam core under bending condition

    含泡沫鋁芯的復合板彎曲疲勞行為的研究
  3. Based on the results of experimental research, we can find that the construction method of joints zone are feasible and safe, the joints between concrete - filled steel tubular core columns and prestressed concrete beams have good ductility and good energy dissipation, and the concrete - filled steel tubular core columns can raise the shear strength of core area of joints and the bending strength of the column ends

    試驗研究發現，針對該節點所設計的構造處理方式是可行的、安全的，鋼管混凝土核心柱與預應力混凝土梁框架節點有著很好的延性和能量耗散能力，由於柱為鋼管混凝土核心柱，大大提高了節點核心區的抗剪承載力，同時也使柱端抗彎承載力得到加強。
  4. The stress field, strain field and energy formula have been established as the base of 3d fem simulation of nc tube bending process. a 3d fem simulation program of nc tube bending is developed based on the ansys software platform, and some key techniques have been studied. used this program as a core, nctbs system which combines with cad / cae / capp / cam subsystems on the database is developed

    基於ansys軟體編制了數控彎管三維有限元數值模擬程序，對其中的關鍵技術問題作了處理；以此程序為核心，基於數據庫技術自主設計開發了數控彎管模擬系統（ nctbs ） ，集成了數控彎管cad / capp / cae / cam子系統，通過考核驗證了系統的可靠性，實現了廣義的計算機輔助數控彎管工藝設計和質量保證系統。
  5. The bending radius of a three - core cable should not less than 15 times of the cable diameter

    5 、電纜彎曲半徑：三芯電纜不小於電纜外徑15倍；單芯電纜不小於電纜外徑20倍。
  6. The allowed working temperatureof the core is 65 its smallest bending radius issixtimes the size of cable diameter. the yellow sheath calbe shoulo not be exposed in the sun for long

    線芯長期允許工作溫度65 ，電纜的最小彎曲半徑為電纜直徑的6倍。黃色護套電纜不得在日光下長期暴露。
  7. Details of dcfs with the rip is analyzed, including the relation of dispersion and wavelength, variation of dispersion in the c - band, cutoff wavelength of the basic mode, distribution of scalar field and power, macro - bending loss at 1550nm. based on the optimized rip, impaction of radius of core and width of depressed cladding is studied. at the s ame time, a wavelength devision multiplexing system is designed

    接著對這種結構的光纖作了分析，包括它的色散與波長之間的關系，色散在c - band的變動范圍，標量場的分佈，基模在光纖中的功率分佈，在1550處的宏彎損耗等。
  8. Test method for properties of investment casting ceramic core - part 3 : determination of bending strength

    熔模鑄造陶瓷型芯性能試驗方法第3部分:抗彎強度的測定
分享友人
分享到 Line

分享到臉書