cover mold 中文意思是什麼
cover mold
解釋
蓋模-
Design of multi - cavity mold for the rubber dust cover
軌道交通噪聲控制結構設計及吸聲材料研究 -
This paper referred to the massive domestic and foreign technical material, elaborated in the sheet forming value simulation theory essential technology in detail, points out when analysis sheet forming question should use the big distortion ball plasticity fem and introduce the application characteristic and the function summarizes of the sheet forming simulation software dynaform. secondly, analyzed the cover forming characteristic, simultaneously introduced the influence cover forming factor in detail : such as ramming direction, the craft addendum surface and the material pressing surface, the radius of convex - concave mold, draw bead, pressure strength, blank size and craft margin and so on. and simulates many typical automobiles cover panel with software : such lateral board, back taillight pedestal and storage cover
其次，分析了覆蓋件成形的特點和要求，同時詳細介紹了影響覆蓋件成形的因素如沖壓方向、工藝補充面和壓料面、凸凹模圓角、拉延筋、壓邊力、坯料尺寸和工藝切口等，並用數值模擬軟體對多個典型的汽車覆蓋件汽車后側圍板、后燈座以及轎車后備箱蓋的沖壓成形情況進行模擬，用模擬結果優化拉延工藝方案，比較了內覆蓋件和外覆蓋件在成形特點和要求的一些異同點，以及常見的起皺、拉裂和回彈、成形不足等缺陷的產生機理和相應對策，重點介紹工藝補充面和壓料面的設計及優化方法，因為拉延是沖壓工藝的關鍵工序，而工藝補充面和壓料面的設計是拉延工序的關鍵，對消除缺陷至關重要。 -
Design and manufacture of rubber injection mold for rubber lining cover
橡膠襯套壓注模的設計與製造 -
But in automobile body cover ramming process the technical difficulty is the ramming craft formulation and the mold designs. reasonable ramming craft and high grade mold, not only can improve the pressing part quality and productivity, also reduces the waste product rate
而在車身覆蓋件的沖壓過程中其技術難點是沖壓工藝的制定和模具設計，合理的沖壓工藝及高質量的模具，不但能提高沖壓件質量，還能提高生產率，降低廢品率。 -
In automobile body manufacture process the cover panel design, the mold design and the manufacture processing occupies 60 % of the entire processing of automobile body design and the process. reduces this time for a while means speeds up the development of new vehicle type, and the cycle time of product puts in market
在車身製造過程中覆蓋件的設計和模具設計及加工占整個車身設計和加工周期的60 %左右，縮短這一時間就意味著加快新車型的開發，縮短產品投放市場的周期。 -
Stir in the walnuts and cranberries. spoon it into the prepared mold or dish. cover tightly with foil. place it on a wire rack in a large steamer or kettle
放入胡桃和小紅莓並攪拌。用勺將其舀到已準備妥當的模子或砂鍋中。用箔紙蓋嚴。將其放到大蒸鍋或水壺中的網架上。
分享友人