crank pin 中文意思是什麼

crank pin 解釋
曲柄箱銷
  • crank : n 1 【機械工程】曲柄；（刑具）旋盤。2 （言語或思想的）奇特的轉折；狂想，幻想；〈美俚〉想法古怪的...
  • pin : PIN ＝personal identification number 個人標識號〈自動提款卡等的個人密碼〉。n 1 別針，扣針，飾針；...
  1. Cycles. cotter pin and assembly of the axle cotter pin crank

    自行車.扁銷和輪軸扁銷曲柄總成
  2. Adjust the amount of oil supplied to the thread take up and needle bar crank 3 by turning adjust pin 4

    調整挑線桿和針桿曲軸部3的油量時，轉動油量調整銷4進行調整。
  3. The minimum amount of oil is reached when marker dot a is brought close to needle bar crank 3 by turning the adjust pin in direction b

    調詳銷刻點a從圖的位置向b方向轉動，轉動到接近針桿曲軸3時，油量最小。
  4. The maximum amount of oil is reached when marker dot a is brought to the position just opposite from the needle bar crank 3 by turning the adjust pin in direction c

    從圖上所示的位置向c方向轉動，當轉到與針桿曲軸3的正對面的位置時，油量為最大。
  5. The reassigned smoothed pseudo wigner - ville distribution ( rspwvd ) is introduced, which has less interference and higher resolution than other time frequency distributions like wigner - ville, choi - williams etc. it is used to detect the multi - knocking of engine such as cylinder, piston pin, valve, crank bearing, connecting rod bearing and jib knocking. a new fault diagnosis technique based on the rspwvd for the engine multi - knocking problem is proposed. by comparing the bispectrum and bicoherence of the gear vibration signals, it is demonstrated that bispectrum has an advantage over bicoherence for feature extraction of such signals

    第四章首次引入一種重分配方法，得到干擾項少而解析度高的重分配平滑偽魏格納維爾分佈（ rspwvd ） ；對發動機曲軸主軸承響、連桿軸承響、活塞銷響、活塞敲缸響、氣門響和挺桿響等常見機械異響故障振動信號特徵進行了全面地比較分析；通過對各種異響故障特徵信號的分析研究，提出基於rspwvd的發動機多異響故障診斷策略，利用該策略可以準確識別不同的發動機異響故障。
  6. Bell crank pin

    水閥曲拐銷子
  7. Crank pin bushing

    曲柄銷襯套
  8. Double crank four ring - plate - type pin - cycloidal gear planetary drive driven by two motor is a new - type pin - cycloidal gear planetary that has practical value

    摘要雙電機驅動雙曲柄四環板針擺行星傳動是一種具有實用價值的新型擺線針輪行星傳動。
  9. Crank pin bearing

    曲柄銷承
  10. The results of analysis show that : 1 ) doi of the pin - axis errors, especially the crank - pin - axis errors, is bigger than other axis errors ; 2 ) from the calculating results of doi of the errors of the different kinematic pairs, doi of rotate - completely pairs is bigger than that of oscillate pairs ; 3 ) the forced coupler - deformations resulted from the constraints out of motion plane consist of twisting and bending deformation, and the deformations are variat

    （ 4 ）首次提出了運動副誤差對平面連桿機構約束不確定性影響度的評判指標和單因素定量分析方法，得到了機構中不同運動副的不同平面內的誤差對機構性能的影響程度。本文的分析計算結果表明，平面連桿機構中的非平面約束所造成的連桿強制變形中既有扭轉變形又有彎曲變形。
  11. The mechanisms and conditions for the mechanisms to adjust itself were analyzed in detail. an accurate method of analyzing for the properties of the mechanisms without overconstraints was given for the first time, we obtained the equations of self - adjusting displacement in the cylindrical pair, the allowable kinematic - pair - axis errors which enable the mechanisms realize function of self - adjustment, and the most rational arrangements of kinematic pairs for the three common four - bar mechanisms. the results of analysis show that the influences of the errors of crank - pin on the self - adjusting properties of the mechanisms are bigger than that of the other pairs

    （ 3 ）詳細分析了無過約束機構能夠實現自調的機理及機構能夠實現自調的條件，首次提出了無過約束機構自調性分析的一種精確方法，得到機構自調時圓柱副中的自調位移規律和機構能夠實現自調的運動副允許誤差角以及三種常用平面四桿機構的自調結構的最適宜的運動副配置方式。
  12. Crank pin turning machine

    曲柄銷旋削機
  13. Crank pin collar

    曲柄銷墊圈
  14. Crank pin washer

    曲柄銷墊圈
  15. Crank pin stud

    曲柄銷螺釘
分享友人
分享到 Line

分享到臉書