cross beams method 中文意思是什麼

cross beams method 解釋
擬梁法
  • cross : n 1 十字架；〈the C 〉 耶穌受刑的十字架。2 〈the C 〉 基督教（教義，國家）。3 不幸，苦難；挫折，...
  • beams : 比姆斯
  • method : n 1 方法，方式；順序。2 （思想、言談上的）條理，規律，秩序。3 【生物學】分類法。4 〈M 〉【戲劇】...
  1. When analyzing skew support continuous curved box girder bridge, curved grid girder analyzing method considering warping effect is applied. matrix displacement method is applied in analyzing skew support continuous curved thin - walled box girder bridge with restrained bearing. in order to convert original rigidity equations to structural rigidi ty equations that can be solved, bearing nodal displacement matrix can be introduced, then unknown quantities at the edge of beams can be consistent with the restrained directions of skew bearings, unit rigidity matrix and unit nodal forces can be gained. structural rigidity matrix can be composed according to matrix displacement method, so nodal displacements and inner forces on the end of the rod that are unknown can be gained calculating equations of inner forces on any cross - section can be solved

    分析斜支承連續曲線箱梁橋時，採用考慮翹曲作用的曲線格子梁分析方法，應用矩陣位移法對具有約束支承形式的斜支承連續曲線薄壁箱梁橋進行分析，考慮到支座的約束條件並不與梁端彎曲角位移和扭轉角位移的方向一致，引入支座節點坐標矩陣，使得梁端的位移未知量與斜支座約束方向一致，來計算單元剛度矩陣和單元節點力，然後按照矩陣位移法組集總剛並建立結構剛度方程，根據結構剛度方程即可求解未知的節點位移及桿端力，推導出任意截面處的內力計算公式。
  2. Regarding the rc beams subjected to concentrated load or even load and braced by bonding steel, an analysis is made on the relevant factors influencing maximum anchorage shear stress of steel sheet. the analysis is based on elastic theory and makes use of the formula for calculating anchorage shear stress of steel sheet. as indicated by the results, the maximum anchorage shear stress not only realtes to such parameters as height of cross section of rc beam and span but also relates to the thickness of adhesive layer, elastic modulus, thickness of steel sheet, and length of steel sheet. the present method will check maximum an chorage shear stress on the end of shear sheet so as to prevent rc beam from local damage. the present results will offer important reference for our country to further perfect bracing design by bonding steel method

    在彈性理論的基礎上，利用鋼板錨固剪應力計算公式，對在集中荷載或均布荷載作用下採用粘鋼加固的混凝土梁，分析鋼板錨固最大剪應力的有關影響因數.結果表明，最大錨固剪應力不但和混凝土梁的截面高度、跨度等參數有關，還和粘膠層厚度、彈性模量、鋼板厚度及鋼板長度有關.採用文中方法可以對鋼板端部最大錨固剪應力進行驗算，防止混凝土梁出現局部受拉破壞.研究結果為進一步完善我國粘鋼法加固設計提供重要的參考資料
  3. The crack analysis and repair method of cross beams in steel constructed factory buildings

    鋼結構廠房橫梁開裂分析與修復
分享友人
分享到 Line

分享到臉書