cutting parameters 中文意思是什麼

cutting parameters 解釋
切削參數
  • cutting : n 1 切斷，切下；切片；【園藝】扦插，插條；〈英國〉剪裁，（報紙等的）剪輯；（寶石等的）加工，琢磨...
  • parameters : 編輯特徵參數
  1. The frozen coal destruction is the tension stress destroys, and establish the frozen coal cutting model in this foundation, obtains the cutting force, feeding force, tooth spacing according to the smallest energy principle. bring forward a rotary drilling mothod to unload the frozen coal, the broken ability is strong, without frozen depth limits, then obtains this machine working parameters, has combined this method with a grab and determined the plane of vehicle - carried rotary drilling movable coal - unloader

    凍煤破壞是拉應力破壞，在此基礎上建立了凍煤的切削模型，根據最小能量原理得到截割力，進給力和截齒間距的計算公式，分析得到截割力與切削厚度成正比，隨著前角的增大而減小;截齒最優截距與截齒尺寸有關且與切屑厚度成正比;進給力隨著截齒前角增大而增大的規律。
  2. Analyse the tooth geometry of klingelnberg cyclo - palloid spiral bevel gear., according to the relative position and kinematic relation of the cutter heads, virtual crown gear and the processed wheel blank, established the system of coordinates of the gear cutting, dedcuced the tooth face equation of the virtual crown gear, according to relations of the gear cutting and space theory of engagement, deduced the tooth face equation of klingelnberg cyclo - palloid spiral bevel gear, and drawing the three - dimensional graphs of the virutal crown gear and klingelnberg cyclo - palloid spiral bevel gear according to the design and setting parameters

    對克林貝格擺線齒錐齒輪進行齒面幾何分析。根據銑齒加工中刀盤、搖臺和輪坯的相對位置和相對運動關系建立了切齒嚙合坐標系，由矢量的旋轉推導了產形輪齒面方程;根據空間嚙合原理和切齒嚙合關系推導了被加工齒輪的齒面方程;由設計參數和銑齒調整參數計算得到齒面離散數據，繪制了產形輪和擺線齒錐齒輪的三維齒形。
  3. Cutting parameters limited method of arced lath tool in cnc curved mightily turning

    圓弧車刀數控強力曲面車削用量的極值法
  4. In the light of the problems of the air balance system of model lcj1250 chain drive pumping unit, it is proposed to change the air balance with counterweight balance, and three criteria for the modification is put forward : ( 1 ) ensuring the reliability of the unit with smooth operation, low noise and long life ; ( 2 ) cutting down the production cost and using less component parts as possible ; ( 3 ) carrying out modification without such main technical parameters as stroke, pumping speed and maximum polished rod load

    針對lcj1250氣平衡式鏈條抽油機存在氣平衡故障率高和現場維修困難等問題，提出將氣平衡改造成工作可靠的重力平衡的方案，並確定了改造的三個原則：一是保證整機的可靠性，使抽油機運轉平穩，振動噪音小，壽命長；二是力求降低生產成本，減少零部件製造，盡可能選用原來的通用件，捨去平衡缸和空氣包等氣平衡附件，在原往返架主體上懸掛一個配重箱；三是力求不改變沖程、沖次及最大懸點載荷等主要技術參數。
  5. Abstract : in the light of the problems of the air balance system of model lcj1250 chain drive pumping unit, it is proposed to change the air balance with counterweight balance, and three criteria for the modification is put forward : ( 1 ) ensuring the reliability of the unit with smooth operation, low noise and long life ; ( 2 ) cutting down the production cost and using less component parts as possible ; ( 3 ) carrying out modification without such main technical parameters as stroke, pumping speed and maximum polished rod load

    文摘:針對lcj1250氣平衡式鏈條抽油機存在氣平衡故障率高和現場維修困難等問題，提出將氣平衡改造成工作可靠的重力平衡的方案，並確定了改造的三個原則：一是保證整機的可靠性，使抽油機運轉平穩，振動噪音小，壽命長；二是力求降低生產成本，減少零部件製造，盡可能選用原來的通用件，捨去平衡缸和空氣包等氣平衡附件，在原往返架主體上懸掛一個配重箱；三是力求不改變沖程、沖次及最大懸點載荷等主要技術參數。
  6. The connection between the torque and the polarized charges is established. on the base of mathematical model of torsional effect, using multivariate unrestrained nonlinear optimization method, we research cutting angles and parameters of crosssection to get best torsional sensitivity

    在建立石英晶體扭轉效應模型的基礎上，應用多變量、無約束非線性優化方法對于晶體切型、截面形狀等參數進行了優化，以獲得最佳扭轉靈敏度。
  7. Optimization of nc turning cutting parameters

    數控車削切削用量的優化
  8. Optimization of cutting parameters of endless diamond wire saw

    環形電鍍金剛石線鋸鋸切工藝參數的優化
  9. Experience with selecting cutters and setting up the cutting parameters

    合理選擇刀具和設置加工參數。
  10. Study of optimization of the multi - goal cutting parameters in nc turning

    數控車削的切削用量多目標優化
  11. Cutting force modeling in turning based on cutting parameters and tool condition

    基於切削參數和刀具狀態的車削力模型
  12. Sewing and garment machines - terms of sewing technology - part 5 : auxiliary equipment, cutting parameters

    縫紉和制衣機.縫紉技術術語.第5部分:輔助設備和剪裁
  13. Operating parameters storage : saving up to 30 files, cutting time needed for different shoe styles

    操作用參數記憶存檔- - -最多可記憶三十組計時器及動作參數，方便更換鞋型。
  14. A cutting force model in turning on cutting parameters ( the depth of cut, feed rate, workpiece material and tool material ) and tool condition ( focusing on tool flank wear ) was developed

    摘要建立刀具狀態監控特徵量與切削參數及刀具狀態之間的定量或定性關系是實現刀具狀態監控系統的基礎。
  15. On the basis of the theory of fractal geometry, the fractal dimension characters of ae signal at different tool wear states were analyzed, an algorithm was provided to decide the scale range which is necessary to calculate the dimension of non - fully - fractal form. the experiments showed that the fractal dimension of ae signal is slightly effected by the changes of cutting parameters ; the variance of the fractal dimensions, which reflects the geometric characters of ae signals, has the same tendency as that of the flank wear, the monitoring system, which takes the fractal dimension of the ae signal as the feature, can identify the different tool wear states more correctly under different cutting conditions

    以分形幾何理論為基礎，對刀具不同磨損階段聲發射信號的分形特徵進行分析.提出了計算非完全分形體信號波形的關聯維數時尺度范圍的確定方法，分析了聲發射信號在刀具磨損過程中分形維數的變化特性.刀具磨損切削實驗數據表明，聲發射信號的分形維數受切削參數變化影響較小；分形維數反映了聲發射信號的幾何特徵，其大小能較好地反映刀具的不同磨損狀態.實驗結果表明，該方法能正確地實時在線監測刀具的不同磨損狀態
  16. This paper mainly aims at the strategic demands for large - aperture lightweight mirror proposed by high - tech development. its main research contents are : select material blank for lightweight mirror according to physical and chemical properties of optical glass ; analyze and calculate the deformation quantity of the mirror with finite element method ; design and optimize mirror body structure of 400 lightweight plane mirror and 450 lightweight spherical mirror, analyze glass cutting principle, design specisl - use grinding wheel structure, select reasonable technological parameters to implement the processing of weight reduction holes on 400 plane mirror ; analyze etching mechanism of hydrofluoric acid, look for the technological parameters such as the optimal acid concentration and etching time etc. ; eliminate the stress of weight reduction holes and micro - cracks on 400 lightweight plane mirror ; discuss the processing principle and

    本論文的研究主要是瞄準國家高技術對大口徑輕型鏡的戰略需求而開展的。主要研究內容是：根據光學玻璃的物理與化學性能，選擇輕型鏡坯材料；用有限元法對鏡子的變形進行分析、計算，找出變形規律，優化設計400mm輕型平面鏡、 450mm輕型球面鏡鏡體結構；分析玻璃切削原理，設計專用磨輪結構，選擇合理工藝技術參數，完成400mm平面鏡輕量化減重孔的加工；分析氫氟酸腐蝕光學玻璃機理，尋找最佳酸濃度、腐蝕作用時間等工藝參數，實現400mm平面鏡減重孔應力與微裂紋的消除；討論分離器加工原理和工藝技術特點，完成400mm平面輕型鏡面形加工。
  17. The signals of sawing force with different cutting parameters were acquired by a piezoelectric force dynamometer in the process of sawing concrete, and the characteristics of the sawing force signals and the influence factors were analyzed

    採用壓電磨削測力儀和信號採集系統測量了不同鋸切參數條件下的鋸切力，分析研究了鋸切混凝土過程的鋸切力信號特徵和影響因素。
  18. Fang qing ? hua, liang pei ? zhi, li zhi ? gang. optimization of cutting parameters in mold cavity milling j. die and mold technology, 2002, 2 : 4749

    方清華，梁培志，李志剛.模具型腔加工參數的優化問題j .模具技術， 2002 ， 2 : 4749
  19. When they program they often set conventional cutting parameters for some things, such as machining remains, material ' s asymmetry and tools " wear cannot be premeditated, which will be blighted to the quality of the machining workpieces

    在編程中往往無法預先考慮實際加工過程中出現的一些情況如：加工余量的不一致、工件材質的不均勻、刀具的磨損等對加工質量的不良影響，將加工參數設置得較為保守。
  20. The module can finish the tooth geometry parameter calculation, stress analysis calculation, stress checking calculation, cutting parameters calculation. datas can be saved at the designated path. ( 3 ) the parametric drawing and modeling module for klingelnberg cycloid bevel gears was implemented on autocad 2004 platform based on activex automation technique

    （ 2 ）採用面向對象的visualbasic6 . 0編程語言編制了計算機輔助設計計算模塊，程序中針對部分參數採用了相應的數值計算方法進行求解，實現了克林貝格擺線錐齒輪的計算機輔助幾何設計計算、受力分析、強度校核、切齒調整計算功能，並可以將數據保存於指定路徑下。
分享友人
分享到 Line

分享到臉書