cycloid tooth 中文意思是什麼
cycloid tooth
解釋
擺線齒-
The main research work in the thesis is as follows : ( 1 ) base on the analysis of cutting principle and tooth geometry characteristics of klingelnberg cycloid bevel gear, the formula of tooth design calculation was verified and the equation of imaginary crown gear tooth flank was deduced by establishing appropriate coordinate system
主要研究工作和成果有: （ 1 ）通過分析克林貝格擺線錐齒輪銑齒原理，對其部分幾何設計演算法進行了推導驗證，並建立了適當的坐標系推導了假想冠輪的齒面方程。 -
As both the meshing point and ball ' s center are on the given cylinder, a general method for developing the cam ' s profile is studied. it is proved that the profile of positive and negative transmission is unique if the face gear, the difference between face tooth number and ball number and the diameter of ball are the same. the concrete expression of meshing cam on given spatial cycloid profile, and the characteristics of the profiles are discussed
論文的主要工作包括： 1 、根據嚙合點和鋼球中心軌跡均在同一圓柱面上的特點，研究了給定端齒齒廓條件下求解凸輪齒廓的一般方法；論證了在給定端齒、齒差數和鋼球直徑相同的條件下，正負齒差嚙合齒廓的唯一性；討論了端齒為球面擺線時，凸輪齒廓的具體表達式，並研究了該齒廓的性質。 -
Spiral bevel gear presents serials of good performance at transimision, carrying capability etc, of which klingelnber cycloid bevel gear is mostly widely used. it has its own characteristics : ( 1 ) the concave and convex flanks of the gear slot are cut at the same time continuously, this benefit to improve productivity. ( 2 ) universal double cutter heads are used which make it easier to control the tooth contact area
螺旋錐齒輪具有傳動性能優良，承載能力高的優點，克林貝格擺線錐齒輪是一種最具代表性的螺旋錐齒輪齒制，除具有一般螺旋錐齒輪的優點外還具有以下的特點: （ 1 ）採用連續分度雙面法銑齒，避免了跳齒分度，有利於提高加工精度。 -
2. the splitting method, enclosed planetary transmission sketch method and structure sketch method are used to deduce the transmission ratio formulas on several structures of the single - stage and double - stage spatial - cycloid - ball gearing respectively. further more, the simplified calculating formulas on one - tooth - difference and two - tooth - difference spatial - cycloid - ball gearing are given
2 、分別運用拆分法，封閉行星機構的傳動簡圖和結構簡圖推導出單級和雙級的多種結構的傳動比公式，並給出一齒差、二齒差球面擺線鋼球傳動機構減速比的簡化計算公式。 -
The module can finish the tooth geometry parameter calculation, stress analysis calculation, stress checking calculation, cutting parameters calculation. datas can be saved at the designated path. ( 3 ) the parametric drawing and modeling module for klingelnberg cycloid bevel gears was implemented on autocad 2004 platform based on activex automation technique
（ 2 ）採用面向對象的visualbasic6 . 0編程語言編制了計算機輔助設計計算模塊，程序中針對部分參數採用了相應的數值計算方法進行求解，實現了克林貝格擺線錐齒輪的計算機輔助幾何設計計算、受力分析、強度校核、切齒調整計算功能，並可以將數據保存於指定路徑下。
分享友人