cylinder rod 中文意思是什麼

cylinder rod 解釋
活塞桿
  • cylinder : n 1 圓筒；機筒；烘筒；量筒；（印刷機等的）滾筒。2 【數學】柱（面），柱體。3 【機械工程】汽缸；【...
  • rod : ROD ＝rewritable optical disc 【計算機】可重寫光盤〈其內存信息可由激光讀出並加以編輯的光盤〉。n 1...
  1. Markmaking on the part in the motorcycle and automobile, e. g. body 、 frame 、 chassis 、 connecting rod 、 motor 、 cylinder with serial number 、 title 、 trademark and scutcheon, etc

    汽車、摩托車標牌及零部件打標、如車身、車架、底盤、連桿、發動機、氣缸等列印編號、名稱、商標等內容。
  2. The reassigned smoothed pseudo wigner - ville distribution ( rspwvd ) is introduced, which has less interference and higher resolution than other time frequency distributions like wigner - ville, choi - williams etc. it is used to detect the multi - knocking of engine such as cylinder, piston pin, valve, crank bearing, connecting rod bearing and jib knocking. a new fault diagnosis technique based on the rspwvd for the engine multi - knocking problem is proposed. by comparing the bispectrum and bicoherence of the gear vibration signals, it is demonstrated that bispectrum has an advantage over bicoherence for feature extraction of such signals

    第四章首次引入一種重分配方法，得到干擾項少而解析度高的重分配平滑偽魏格納維爾分佈（ rspwvd ） ；對發動機曲軸主軸承響、連桿軸承響、活塞銷響、活塞敲缸響、氣門響和挺桿響等常見機械異響故障振動信號特徵進行了全面地比較分析；通過對各種異響故障特徵信號的分析研究，提出基於rspwvd的發動機多異響故障診斷策略，利用該策略可以準確識別不同的發動機異響故障。
  3. Comparision of o - ring, un - cup, and che - cup seal used in single rod cylinder at ultra high pressure

    車氏三種密封圈在超高壓單作用缸中的應用對比研究
  4. Abstract : the flying shear located behind the roughing stands of wire - rod mill is designed with hard surface gears for driving system, engaging of zero tolerance, hydraulic cylinder for clamping and shiftting, convenient and practical gap adjusting structure for blade

    文摘:介紹了邯鋼三軋廠在線材軋機粗軋機組后的飛剪設計中，採用了硬齒面齒輪傳動，零側隙嚙合，液壓缸鎖緊與橫移及簡便實用的剪刃間隙調整機構。
  5. When the governing valve was series - connected on the return oil - line in the metering - out control system, under the same flow area and the same adjusted pressure of relief valve, with the incremental quantity of step load, the pressure highly - adjusted capacity of the hydraulic cylinder chamber with piston - rod increased, meanwhile, it ' s time of rise, time to peak and the governing time all increased. at the same time, the pressure highly - adjusted capacity of the hydraulic cylinder chamber without piston - rod increased

    當出口節流調速系統的回油路上串接調速閥時，隨階躍負載的增加，在相同流量閥開度、相同溢流閥調節壓力的情況下，液壓缸有桿腔壓力p _ 2 （ t ）的超調量是增加的，上升時間、峰值時間以及調整時間也是增加的；液壓缸無桿腔壓力p _ 1 （ t ）的超調量是增加的。
  6. According to the control rod hydraulic drive mechanism ( crhdm ) and the characteristics of its hydraulic cylinder seal structure, the leaking ways of the hydraulic cylinder piston ring seal were analysed, its theoretical calculation model was built and its flow resistance formula based on the calculation model of differential pressure at the hydraulic cylinder piston ring seal was deduced

    摘要根據控制棒水壓驅動機構水壓缸活塞環密封結構的特點，分析了水壓缸活塞環的泄漏途徑，建立了活塞環密封泄漏流阻的理論計算模型，並結合水壓缸活塞環密封處的壓差計算模型，推導出水壓缸密封結構的流阻計算公式。
  7. Cylinder bore and piston rod diameters - inch series

    汽缸孔和活塞桿直徑.英制系列
  8. It is suitable for an internal hole grind of the larger hole diameter, such as cylinder, cylinder sleeve and connecting rod, oil pipe and etc

    適用於較大孔徑之內孔研磨，如汽缸汽缸套及連桿油料管等。
  9. It is suited for the larger hole diameter internal hole grinding, for example, a cylinder, a cylinder sleeve and connecting rod, oil pipe and etc

    適用於較大孔徑之內孔研磨，如汽缸汽缸套及連桿油料管等。
  10. The change to the construction of piston and rod of a cylinder

    對氣缸活塞及活塞桿結構的改進
  11. Fluid power systems and components - cylinder - rod wiper - ring housings in reciprocating applications - dimensions and tolerances

    流體傳動系統和元件.缸筒.往復用活塞桿刮油漲圈.尺寸和公差
  12. The key position bolt of the engine include connecting rod, crankshaft, main bearing, cylinder head, flywheel and shock absorber bolt, all of which belong to bolt fastening

    發動機關鍵工位螺栓包括連桿螺栓、曲軸螺栓、主軸承蓋螺栓、氣缸蓋螺栓、飛輪螺栓和減振器螺栓等均屬螺紋聯接。
  13. Fluid power systems and components - cylinder bores andpiston rod diameters

    液壓氣勸系統及元件缸內徑及活塞桿外徑
  14. Fluid power systems and components - cylinder bores and piston rod diameters - metric series

    流體動力系統和部件.液壓缸內徑和活塞桿直徑.米制系列
  15. Hydraulic fluid power. cylinder. rod end spherical eye for 160 bar single - rod cylinder, compact serie a

    液壓傳動.千斤頂. 160bar小型a千斤頂活塞桿端頭的球頭銷定
  16. Hydraulic fluid power - cylinder rod and piston seals for reciprocating applications of bearing rings - dimensions and tolerances

    液壓缸活塞和活塞桿動密封裝置用支承環尺寸系列和公差
  17. Hydraulic fluid power - cylinder rod and piston seals for reciprocating applications of bearing rings - dimansions and tolerances of housings

    液壓缸活塞和活塞桿動密封裝置用支承環安裝溝槽尺寸系列和公差
  18. Hydraulic fluid power - cylinder rod and piston seals for reciprocating applications of co - axial seals - dimensions and tolerances

    液壓缸活塞和活塞桿動密封裝置用同軸密封件尺寸系列和公差
  19. Hydraulic fluid power - cylinder rod and piston seals for reciprocating applications of co - axial seals - dimensions and tolerances of housings

    液壓缸活塞和活塞桿動密封裝置用同軸密封件安裝溝槽尺寸系列和公差
  20. Hydraulic fluid power - cylinder rod and piston seals for reciprocating applications - dimensions and tolerances of housings

    動密封溝槽型式尺寸和公差
分享友人
分享到 Line

分享到臉書