deviation in range 中文意思是什麼
deviation in range
解釋
距離偏差-
The device turns round at the range of 360, and locomotive block moves in linear guide in every unit zone. so optical fiber can arrive everywhere in focal plane. experiment result elucidation : the standard deviation of repeat error and positioning error less than 40 microns, the positioning precision of this system can reach demand
用7根單元機構模擬4000根單元的相互關系，實驗結果表明：機構的重復性誤差和目標點定位誤差的均方根值均在定位精度要求范圍之內，能夠滿足望遠鏡快速、準確的定位要求。 -
In order to solve the problem of deviation of suitable angle andthe practice of shot put, the author analyzes the function relation between performance and the maximum projectile range, draws the best result theorem that is new optimum angle formula and sign - line parameter
為了解決鉛球適宜投出角度公式與實踐偏離的問題，分析了鉛球成績與拋體最大射程的函數關系，得出了最大成績定理、 「新」最佳投出角度公式和最佳出手角度標志線參數式。 -
Earlier, when we calculated the range, the interquartile deviation, and average absolute deviation, the answers were expressed in the same units as the data itself.
當我們計算極差，四分點離差和平均絕對偏差時，答案的計量單位與數據單位量相同的。 -
After clustering of the documents, in the process of retrieval, we make a comparison between the retrieval words the users point out and cluster center of the documents, and as a result, achieve a cluster that is most similar to retrieval words. through the calculation of both the selected documents and those retrieval words, thence the retrieval range will be reduced, the efficiency of retrieval be increased, and the retrieval deviation be overcome to a certain extent
對文檔進行了聚類，在檢索的期間，對用戶提出的檢索詞先進行和每一類的類心比較，得到與之最近的類別，僅將屬于該類別中的文檔與用戶提出的檢索詞進行運算，從而縮小了檢索的范圍，提高了檢索的效率，也在一定程度上克服了檢索結果的偏差。 -
In this paper, the transitional method of the spherical har monics is applied and a new model is gained. the parameters of the new model are geocentric radius, range cross - deviation and polar is decided by different trajectories
本文對球諧函數的改進主要是採用了換極法，根據不同的彈道重新選擇極點，將球諧函數變換為以地心距、射程角、側向偏差為參數的新的形式。 -
For the operation performance of thsc series of sheet cutters, basically the machine speed of 300 m min and the cutting speed of 500 cut min can be reached in the range of 1400 - 1900 series, but it is hardly to reach it under operation of the remain series, such as : 2100 - 3500, however, still depend on the quality of base paper. the deviation of cutting length is approximately about 0. 3 mm
在運轉性能方面： thsc系列切紙機其裁切紙張線速度最高可達300m min ，切刀數500cut min ，其裁切的長度偏差值為0 . mm ，當裁切多層紙張時，切刀的負載可達600gsm ，可以說是真正高科技高效率的切紙機。 -
And it is commonly regarded as fault - free when the comparative deviation of component parameters are within 5 % of the nominal value, while in practical operations the allowance range could be set flexibly according to different requirements for the circuit performance
通常認為元件參數的相對偏差絕對值在標稱值的5 %范圍內為無故障，但實際上元件的容差是可以根據對電路性能的不同要求而靈活設定的。 -
While the chips are attached to near center or near a edge of subatrate, the mean, deviation and maximum are at the almost same level ; when the chip is attached near a corner, the deviation and the maximum is far larger than those of the above two positions ; during thermal treatment followed, the residual stress demonstrates a regular cycle trend when the chips are attached near center or edge of the substrate and fluctuates in a wide range when the chip is attached near a corner
當晶元粘貼在基板中心和靠近基板邊緣的位置時粘合劑固化后殘余應力的平均值、最大值和數值的分散性皆處于相接近的水平，而當粘貼在基板靠近一角的位置時應力分佈狀況則有很大不同：應力的分散性增大，應力最大值也遠大於粘貼于另外兩個位置時的值。
分享友人