displacement error 中文意思是什麼

displacement error 解釋
偏移誤差
  • displacement : n 1 轉位，移動；取代，置換；（人的）流離失所。2 撤換，免職。3 【機械工程】（活塞）排氣量；【航海...
  • error : n. 1. 錯誤；失錯。2. 謬見，誤想；誤信；誤解。3. 罪過。4. 【數學】誤差；【法律】誤審，違法；（棒球中的）錯打。adj. -less 無錯誤的，正確的。
  1. The analysis of precision about mould - cut main mechanism with clearances is advanced. on the basis of analysis of slider displacement error influenced by the crank length tolerance, the coupler length tolerance and clearances in revolute joints for mould - cut main mechanism, some reasonable suggestions about tolerance distribution of bars length and fitting precision of joints are put forward

    考慮運動副間隙對主切機構進行了精度分析，通過分析主切機構中各桿長誤差和運動副間隙對滑塊位移誤差的影響，對商標模切機設計初期桿長誤差分配和運動副間隙配合精度提出了合理的建議。
  2. This text divides into five chapters altogether : chapter one in the introduction, have introduced the common sensor of displacement, has pointed out the fine characteristic of hall ' s sensor, put forward the basic task ; chapter two have introduced the basic operation principle of hall ' s component ; chapter three introduce hall temperature performance, electromagnetic characteristic, zero error, frequency characteristic and these parameter commonly used compensation method and hall simple application of component ; chapter four having recommended the measurement principle of the feedback servo mechanism, systematic implementation method, the experimental result has appeared, structure the mathematics model, and has analysed the error ; chapter five have pointed out the developing direction in the future while looking forward to

    本文共分為五章：第一章緒論中，介紹了常見的位移傳感器，指出了霍爾傳感器的優良特性，提出了基本任務；第二章介紹了霍爾元件的基本工作原理；第三章介紹了霍爾元件的溫度性能、電磁特性、零位誤差、頻率特性以及這些參數常用的補償方法和霍爾元件的簡單應用；第四章介紹了反饋隨動機構的測量原理，系統的實現方法，給出了實驗結果，構建了數學模型，並對誤差進行了分析；第五章展望中指出了今後的發展方向。
  3. Based on the error theory of point measurement are the identifying of the error range set, sketch of the error ellipse, analysis on displacement of the monitoring sites and error detection, providing a fundamental theory infrastructure for dynamic assessment of surface displacement and gray prediction

    根據點位測量的誤差理論，確定定誤差值域范圍，繪出誤差橢圓；對各監測點進行位移與誤差判別分析，為地表位移動態分析和灰色預測提供理論基礎。
  4. Undershooting error propagation in two kinds of displacement - control modes

    兩種位移控制模式下的下沖誤差傳播
  5. Transformed the six - bar guide - bar mechanism realizing linear displacement in automatic instruments into a basic rotating guide - bar mechanism, established the mathematical model of velocity approaching constant by the classical approximate synthesis theory and the modern error theory, discussedthe influences of the existent region of main mechanismic parameters on kinematic and dynamic properties, analysed the theoretical transmission ratio error, advances systematic, complete steps and methods for dimensional synthesis of this mechanism with computer aided design

    將自動化儀表中實現線性輸出的六桿導桿機構轉化為基礎轉動導桿機構，應用經典的機構近似綜合理論與現代的誤差理論，建立了速度逼近常數的數學模型，討論了主要機構參數存在區域及對運動、動力性能的影響，分析了傳動比理論誤差，提出了系統完整的計算機輔助尺度綜合的步驟與方法。
  6. Data processing is performed by pc ， which includes detecting rough error by quartile method base on first order differential, adopting three points algorithm to eliminate deviations of rack displacement and installation, applying minimum containing area method to evaluate the sectional plane radius of roller and realizing it by genetic algorithm, adopting akima method to fit curve of roll profile

    主要的數據處理工作在上位機進行，採用基於差分法的分位數演算法剔除粗大誤差；採用三點式測量原理消除探頭的安裝及運動所產生的誤差；採用最小包容區域法評定軋輥半徑，並應用遺傳演算法實現最小包容區域法的尋優計算；採用阿克瑪插值方法進行輥型的曲線擬合。
  7. This aberration is referred to as a “ m ” by finite element method. rms of absolute error ( rmsa ) is obtained according to displacement, moreover, the relationship graph between rmsa and pressure offers gist for controlling surface precission

    由位移計算出絕對誤差的均方根誤差（ rmsa ） ，得到氣壓與rmsa為非線性的變化關系，其關系圖為通過控制氣壓來調節反射面的精度提供了依據。
  8. Verification regulation of angular displacement transmission chain error tester

    角位移傳動鏈誤差檢查儀檢定規程
  9. The micro displacement servo system includes step - electromotor, step - electromotor driver, grating displacement sensor and gearing etc. the closed loop position servo system eliminates machining error, fitting error and backhaul error etc. the control will completely run in the platform of windows

    微位移控制系統由步進電動機、步進電動機驅動器、光柵位移傳感器、傳動機構等組成，採用閉環位置伺服控制消除了傳動機構的加工誤差、裝夾誤差、回程誤差等。
  10. Computer simulation result shows that the error is mostly less than 0. 1, if using this method to calibrate against the angular displacement for airplane ’ s rudders

    最後，進行了誤差分析和計算機模擬，結果表明，採用本方案標定精度可達0 . 1 。
  11. The back analysis program is used to calculate rock parameters of an engineering example. the result is good and correct. the error of displacement based on the parameter gained by the back analysis program is little

    將編制的反分析程序應用於某工程計算實例的巖體參數反分析，經檢驗，得到的結果參數理想，準確度較高，用於位移計算誤差較小。
  12. Four groups ’ measurement data are given based on built system, and the results and the error analysis of measurement range of 1. 5, angle step of 0. 06 is discussed in detail. a list table of fitting curve and angular displacement is given as well

    利用建立的測量系統給出了四組測量數據，詳細討論了測角范圍為1 . 5 、角度遞增0 . 06的測量結果與誤差，並給出標定擬合直線與角位移的查找表。
  13. By using the method of error analysis of mbs, the identification equation of geometric error parameters is derived and according to the condition that the rank of coefficient matrix of error measurement equation group must be full, we can get 18 terms geometric error of 3 - axis nc machine tools and three displacement error and three position error

    應用誤差辨識軟體，解得各測量點的十八個誤差參數，即每個運動方向的三個位移誤差和三個位置誤差，再根據實際情況獲得三項垂直度誤差，得到了所有的21項誤差。
  14. Based on the difference between the corresponding limit of displacement from both side of contacted bodies, a local direct error estimator of bem solution for 3d elastic contact problem is presented, and then a scheme of adaptive bem is suggested

    在此基礎上提出將接觸體接觸單元間與域內解連續的邊界位移之差的某種度量作為三維彈性體接觸問題邊界元法的一種誤差直接估計，並且提出了三維彈性體接觸問題邊界元法的一種自適應計算方案。
  15. Displacement function means for calculating geostress in fem analysis of underground houses is used, based on crustal stress data of underground cavern of pump water station of tong guanshan yixing to store energy, applying the displacement function theory and 3d nonlinear fem, the thesis simulates a displacement field applied the boundary in engineering area and obtain the initial crust stress field through load function in ansys. the result shows that the error between regressed ones and actual ones is controlled in allowed limit and supply the important data for building and design

    根據宜興銅官山抽水蓄能電站地下廠房區的地應力實測資料，運用位移函數法理論，採用三維非線性有限元計算方法，反演出施加在廠房區邊界上的位移場，藉助州sys有限元分析軟體，獲取模型邊界節點的坐標信息，然後通過ansys軟體的載荷函數將邊界位移程序化施加到模型邊界上，最後得到整個區域的初始地應力場，結果表明回歸后的地應力值與實測值接近，為地下工程的施工設計提供了重要的資料。
  16. In this dissertation, some basic investigations on the bem of 3d elastic contact problem have been carried out, which can be listed as follows : at first, an early investigation of authors " group, on direct error estimation of bem solution for elasticity problem, is extended from 2d problem to 3d elastic contact problem. an accurate and efficient algorithm for the determination of boundary displacement, which is continuous with the displacement solution within the domain of an elastic body, is then presented

    本文對三維彈性體接觸問題的邊界元法做了若干應用基礎性研究，其中主要包括以下幾個部分：作者首先將本研究組提出的彈性力學問題邊界元解誤差的直接估計從二維推廣到三維問題，給出了確定與域內解連續的邊界位移的一種精確有效的方法。
  17. With different clearance value, displacement curves and velocity curves of generalized coordinates as well as slider displacement error curves in a motion period are obtained. these curves are discussed. results show that if manufacturing cost is kept invariableness, in order to improve precision of mould - cuting, fitting precision of joint connecting the crank and coupler has priority to be considered to increase

    採用四階rong - kuta法求解連續接觸模型的動力學方程，得到了一個運動周期內運動副間隙取不同值時，各廣義坐標的位移、速度曲線和滑塊位移誤差曲線，並通過曲線分析，得出了要提高模切機主切機構精度，在相同加工成本條件下，應優先考慮提高曲柄與連桿鉸接處的配合精度的結論。
  18. The first - order perturbation method correct for forcing decoupling method based on perturbation theory is put forward to decrease error ; iii. the complex modal method is introduced into analysis of non - classical damping systems to eliminate error of forcing decoupling method, and improve the complex modal response spectrum, which can apply to design of non - classical damping systems ; iv. for exerting the energy dissipation capability of each device, a two - step optimum method, whose controlling function is extremum expectation of interbedded displacement, is put forward to optimize the number and position of device ; v. the problem of iterative method applied to analyze energy dissipation systems is indicate, and give some primary advice based on pilot study

    為改善上述缺點，本文進行了以下的研究工作：在忽略耗能器附加質量的基礎上，推導出適用於耗能減震結構的攝動法，減少振型分解法在迭代計算過程中的工作量，加快計算速度；針對運動方程的強行解耦所產生的誤差，根據攝動法原理，對其進行一階攝動修正；為消除強行解耦振型分解法用於非比例阻尼結構分析時產生的誤差，引入狀態空間對系統進行復模態分析，並改進了基於復模態理論的、適用於非比例阻尼結構設計的雙反應譜方法；對于耗能器的數量和位置優化進行了一些探討和研究。
  19. The impulse mode can efficiently reduce the coil heat and measurement error. two measuring methods for the micro - displacement are explored in this paper, and the conclusion is drew that the lever measurement can remarkably improve the result precision. the maximal displacement output of the fabricated actuator is 30 - 40 ju m, the displacement resolution is better than 30nm and the repeatability is nm,

    所研製磁致伸縮型納米微位移致動器，其最大位移輸出范圍： 30 ? 40 m ；最小位移解析度： 30nm ；重復精度： 2nm ，而且整個致動器省棄了復雜的水冷裝置，簡化了結構，縮小了尺寸，顯示了良好的應用前景。
  20. The influence of the detecting array on the spectrum signal is studied. a solution is put forward to correct the displacement error caused by width of the light activated element, when the sampling theorem is satisfied

    提出了在滿足采樣定理的前提下，採用頻域反卷積的方法來消除由像元寬度對光譜峰值定位造成的亞像元誤差。
分享友人
分享到 Line

分享到臉書