dividing circuit 中文意思是什麼
dividing circuit
解釋
除法電路-
Finally, using the low loss 3 - db three port network as power dividing and combing network and using hmmc 5040s fabricated by agilent co. as single - way amplifiers, with the help of e - plane waveguide to microstrip transition, we have designed a two - way power combing circuit with waveguide as interface ports. in 33ghz ~ 35ghz, the measured saturated output power is about 170mw, and the combing efficiency estimated is greater 70 %
最後，採用我們設計的3 - db三埠網路作為功率分配、合成網路，以常用的微帶e面探針作為微帶-波導過渡結構，採用agilent公司hmmc5040作為放大單元，製作出了波導介面的兩路合成電路，在頻率為33 35ghz實測飽和功率達170mw ，合成效率高於70 。 -
Thirdly, it simulated the pumping circuit & dividing circuit with the widely used software matlab / simulink. the displacement of the rod piston and the impact of hydraulic are analyzed in the different input flow ( frequency of pump ) and different reversing time. it found out the cause of hydraulic impact ( one - to - one incorrespondence between the response time of dividing circuit and the operation time of rod piston ), and gave some methods to weaken hydraulic impact. in the final part of the paper, the reliability of the theory analysis is further verified by the experiment of hydraulic system
首先在流變學原理的基礎上，深入分析混凝土在輸送管道內的流動狀態，得出混凝土泵的負載特性方程；然後根據功率鍵合圖的建模方法，建立泵送迴路和分配迴路的數學模型，並運用模擬軟體matlab simulink對泵送和分配迴路模型進行了模擬，分析了在不同的輸入流量（泵送頻率）和換向時間下，活塞桿的位移和系統的液壓沖擊情況，找到了引起液壓沖擊的根本原因（即分配迴路的響應時間（固定值）與活塞桿的運動時間（變化值）不相匹配） ，並提出了相應的改進方法。 -
After analyzed the defaults of the fault dictionary method, several techniques to enhance the capability of the d. c. fault dictionary are presented. these include 1 ) using monte carlo analysis to get the node voltage tolerance, 2 ) using bayesian decision theory to direct the fuzzy set dividing, 3 ) selecting nodes by the fuzzy sets, 4 ) using the fault tree to diagnose the circuit ' s fault with varied sum of nodes
文中分析了字典法存在的問題，提出了改進方法，其中包括：用蒙特卡羅法求各節點電壓的容差域；用貝葉斯決策理論來指導模糊集劃分；以模糊集為特徵進行節點優選；依故障診斷樹進行變節點診斷。 -
In the third chapter, the realizations of the functional circuits are discussed in details such as the realization of the " 200msa / s sampling by parallel adc ", the " high - speed storage of the converted data with different phases ", the " trigger controlling ", the " high - speed transfer by dma " and so on. additionally, the computer simulation of the " data dividing circuit with four different phases ( 0, 90, 180, 270 ) " is given in this chapter
第三章詳細論述「雙a / d并行采樣實現200msa / s采樣」 、 「高速數據流分相存儲」 、 「預觸發采樣控制」 、 「 vc5409與c196hpi通信」 、 「 dma實現高速數據傳輸」等功能電路的實現，詳細說明其工作流程，並給出了關鍵電路? ? 「數據流四相分離」電路的模擬結果。 -
Realization of multi - tooth dividing table control with monolithic integrated circuit
用單片機實現多齒分度臺自動控制 -
Realizes the multi - tooth dividing table control with the monolithic integrated circuit
用單片機實現多齒分度臺自動控制 -
Under the presently conditions, we have designed a low loss 3 - db three port network available in power combing or dividing. since without resistive material, it is different from conventional 3 - db wilkinson hybrid and can fabricated on soft substrate, so simplify technology of circuit fabrication
我們設計出了不同於一般常用的wilkinson電橋的、可用作功率合成與分配網路的低損耗3 - db三埠網路，在32ghz 37ghz頻率范圍內，插損約為0 . 2db 。
分享友人