drawn cylinder 中文意思是什麼

drawn cylinder 解釋
無縫氣瓶
  • drawn : adj. 1. (刀、劍等)拔出鞘的。2. 互無勝負的。3. (禽等)取出內臟的。4. (線等)畫好的。5. 被吸引的。6. (鋼絲等)被拔長的,延伸的,冷拉的。7. (臉等)扭歪的。
  • cylinder : n 1 圓筒;機筒;烘筒;量筒;(印刷機等的)滾筒。2 【數學】柱(面),柱體。3 【機械工程】汽缸;【...
  1. A fresh charge of air-fuel mixture will be drawn into the cylinder as the piston moves down toward.

    隨著活塞朝下止點的向下運動,一些空氣燃料混合氣的新鮮充量將被吸入氣缸。
  2. By way of comparing the results obtained from netting theory, compound theory, nonlinear fem and experimental test, the conclusion could be drawn that matrix crack damage surely existed in the cylinder part of structure. when the structure was subject to internal pressure up to 6. 8mpa, which was the maximum loading of hydrostatic test, the deformation of the global structure and stress and strain distributed in any parts of structure were obtained

    通過對網格理論、復合理論和非線性有限元方法計算結果與試驗值之間的相互比較,可以看出:非線性有限元計算結果介於網格理論和復合理論之間,且有限元計算結果與復合理論結果更加接近,表明在水檢壓力下殼體筒段確實存在著基體開裂等損傷。
  3. In order to verify the feasibility of the present method, chapter 3 takes the fluid flow of sphere, cylinder and the additive mass of two spheres as three examples, finishes the calculation by disposing the source or sink whose strength is expressed as the format of nurbs and emphatically the processing of the singular integral. it can be drawn from the comparison of the results of present method and the theoretical solution, i. e. a good precision can be gotten under a few collocation points with the method

    為了考查本文方法的可行性,第3章以圓球體繞流、圓柱繞流以及兩個等圓球體在流場中的附加質量作為例子,通過在物體表面布置強度以非均勻有理b樣條表達的源匯和著重對奇異積分的處理后完成了相應的計算,從與理論解的比較可以看出本方法的優越:在數目很少的配置點下數值解可取得十分良好的精度。
  4. The regulation of earth pressure ' s distribution in the plane is studied as an emphasis in this paper. regard the equilibrium of the small soil elements close together and the shape ' s characteristics of the cylinder, a formula that is ap plied to describe the distribution of the earth pressure in the plane is put forward, and a comparison with the experiential formula is be drawn

    其中著重研究了大圓筒結構墻後土壓力在平面上的分佈規律,以考慮相鄰兩個圓筒之間的微元土條的平衡為前提,結合大圓筒自身的形狀特點,建立了一組平面上土壓力分佈的計算公式。
  5. The conclusion can be drawn that the method can be applied to the determination of the temperature of a hot wire embedded at the center of a cylinder

    經數值計算驗證,本方法可對薄壁高溫的加熱圓柱體軸線上的熱導線的溫度給出高精度的定量檢測結果。
分享友人