end girder 中文意思是什麼
end girder
解釋
端部大樑-
In order to considering the affections of the adjacent zone out of the girdler section, the internal - forces of two end surface which were obtained by the horizontal shaft system analysis are exerted on each model respectively. moreover, the weight, cable force and prestressing forces including girder longitudinal, diaphragm transverse and inclined web vertical directions are considered
考慮到梁段以外附近區域的作用，在其兩端面上施加了由平面桿系結構分析所得的端面內力，另外，索力和預加力（梁縱向、橫隔梁橫向、斜腹板豎向）也施加在相應的位置，分析了箱形主梁在自重、索力和預應力作用下的空間應力效應。 -
The emphasis of this paper are at : the global design of design system ; the parametric construction of girder, end girder, bridge frame ; the design of user interface ; the further development of two - dimensional drawings ; the realization of interface between girder, end girder structure parts and ansys software
本文的工作重點是:設計系統的總體設計;主梁、端梁、橋架的三維參數化建模;用戶界面的設計;二維工程圖的開發;主端梁結構件與ansys分析軟體介面的實現。 -
When analyzing skew support continuous curved box girder bridge, curved grid girder analyzing method considering warping effect is applied. matrix displacement method is applied in analyzing skew support continuous curved thin - walled box girder bridge with restrained bearing. in order to convert original rigidity equations to structural rigidi ty equations that can be solved, bearing nodal displacement matrix can be introduced, then unknown quantities at the edge of beams can be consistent with the restrained directions of skew bearings, unit rigidity matrix and unit nodal forces can be gained. structural rigidity matrix can be composed according to matrix displacement method, so nodal displacements and inner forces on the end of the rod that are unknown can be gained calculating equations of inner forces on any cross - section can be solved
分析斜支承連續曲線箱梁橋時，採用考慮翹曲作用的曲線格子梁分析方法，應用矩陣位移法對具有約束支承形式的斜支承連續曲線薄壁箱梁橋進行分析，考慮到支座的約束條件並不與梁端彎曲角位移和扭轉角位移的方向一致，引入支座節點坐標矩陣，使得梁端的位移未知量與斜支座約束方向一致，來計算單元剛度矩陣和單元節點力，然後按照矩陣位移法組集總剛並建立結構剛度方程，根據結構剛度方程即可求解未知的節點位移及桿端力，推導出任意截面處的內力計算公式。 -
The main shuchural features of the new electric single - girder overhead travelling crane presented in this paper is as follows : using a special gisder section to provide simple production technology and light weight ; dopting hinged connection at one end between main glrders and end carrages instead of the rigid connection at both ends, eliminating the three - point supporting problem with the crane and thus improving the travelling perfomance ; extending crane wheels life contributed to the combination of no - flange crane wheels and horizontal rollers
提供種生產工藝簡單、自重輕的主梁截面，並將單梁起重機主、端梁的剛性連接改為端用鉸接連接，解決了在製造和軌道安裝時因誤差而造成的大車運行三條腿現象，提高了運行性能；用可調大車運行水平輪中心距的設計，代替帶輪緣的大車輪，提高大車輪的使用壽命。 -
Visual observations showed that a horizontal displacement in the longitudinal direction of the bridge developed between the tie girder and the top flange of the floor beam at the end connection.
肉眼觀察表明：在端節點處的系梁和橫樑上翼緣之間產生一種沿橋梁縱向的水平位移。 -
In the end the stochastic finite element method ( sfem ) is used to point out the key part for maintenance. 9. the girder aqueduct structure of li river of the snwtp as an example is analysised for its risk. every parts of the structure are studied ; the failure modes and failure functions are established
9 、進行了南水北調澧河渡槽的力學風險分析，研究了渡槽各部位的破壞模式，建立了相應的失效模式功能函數，計算了各部位的可靠指標，隨后運用非線性隨機有限元理論詳細分析了渡槽整體結構，得出了一些有益結論。 -
It consists of the girders, trolley and electric equipment etc. the bridge is welded structure of box - type girder, individual drives are adopted for traveling mechanism on each end of the crane. all movements of the crane are controlled from the cabin
本起重機由橋架、小車、電氣設備等到部分組成，橋架採用箱型雙梁焊接結構，大車運行機構採用分別驅動，全部機構均在操場室內操縱。
分享友人